Question about SMC EZ Connect g SMCWEBT-G

1 Answer

Connection Problem Device: SMC-WEBT-G Quantity: 9 pcs FLOOR : 3 floor Connection: Installed One CABLE each floor which is connected to on SMCWEBT-G and the 2 access point is bridge or repeater to the main SMCWEBT-G NOW, my problem is... everytime im going to connect the 1st floor connector to switch... IT STOPS THE CONNECTION. IP configuration is GOOD... Mac address of MAIN is copied to 2 accesspoint and 2 accesspoint mac is entered to main smcwebt-g MODE: configured as Repeater each Device Why is it stop or hangs the connectivity if i am going to connect the 2nd floor the the switch same as the 3rd floor? Any advise or any solution for my configuration? thanks in advance....

Posted by on

  • DannyMagat Mar 17, 2008

    Update only the firmware.......

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 611 Answers

Update the firmware of the all device

Posted on Jun 11, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

While connecting thru router,it showing limited access frequently


Do you leave the router switched on all the time? If not then this can be your problem as some routers can take up to 3 days to get full signal strength and keep it. When switching the router off and powering back up it has to search for the signal again. It will happen whether you are wireless or cable.
If you are wireless and router is always on it may be where it is located, walls can interfere with the signals so try moving it to another area to see if that helps.

Jan 01, 2013 | SMC EZ Connect g WEBT-G 802.11b/g Wireless...

1 Answer

Hi i bought the smc wireless router and i tries to connect it but i couldnt figure out how to connect it because i have a laptop and my internet is connected from my modem to my laptop but i cant seem to...


I'm unsure of the exact part number here but using the model number I checked the manual. This looks like it's just an access point which extends a current network you have. If you only have your laptop, this device and your internet modem it may not give you the wireless connectivity you're looking for. On a normal setup you would plug your modem into a router, plug your laptop into the router and set it up with all your DSL/Cable connection information as well as wireless on/off. You can then unplug from the router and continue life. with this one it's only connecting to an existing setup (another router or another wireless network) and extending it.
If you are looking for a solution to give you a router that connects to your modem and gives you wireless or adding multiple devices on a single connection I would recommend returning this and getting an all-in-one router such as this: http://homestore.cisco.com/en-us/Routers/Linksys-E1000-Wirelessn-router_stcVVproductId97826160VVcatId551966VVviewprod.htm?icid=linksys-specs-e1000-learnmore-btn&src2=linksys-specs-e1000-learnmore-btn

Mar 07, 2011 | SMC EZ Connect g SMCWEBT-G

1 Answer

Cant get connected with my belkin router...all i can get is "connected with limited access


HI

Normal 0 false false false MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman"; mso-ansi-language:#0400; mso-fareast-language:#0400; mso-bidi-language:#0400;} How to quickly install and use your Belkin wireless G router

1. Step 1 Position your Belkin wireless G router.
Place your wireless G router in a wide open and central location. Don't connect the power plug into the router, yet. Make sure your computer is turned off.

2. Step 2 Connect all the devices.
Find the Ethernet cable that connects your PC to the modem. Unplug the Ethernet cable from your PC and insert it into the wireless G router's WAN port. You should have an additional Ethernet cable that came with your router. Take this cable and plug one end into one of the LAN ports on the router. Then connect the other end to your PC's Ethernet port.

3. Step 3 Turn on your modem, router, and PC.
Plug the power plug adapter into the modem. Turn on the modem. It'll take approximately 30 seconds for the modem to boot up. Connect the power plug adapter to the router and the other end into a power strip or outlet. Like the modem, it'll take about 30 seconds for the router to boot. Turn on your PC.

4. Step 4 Verify lights are on for your devices.
Make sure the following lights are on for your router: power, WAN, and LAN light. If you don't see any of them lit, confirm these devices are turned on. Make sure the Ethernet cable connections are installed correctly.
Step 5 Install and configure software.
Use the setup wizard application to configure your Belkin wireless G router. Set up features, such as creating your password and setting up your time zone. Continue to follow the setup wizard so you can configure ?other settings

Oct 18, 2010 | Belkin N1 Wireless-N Wireless Router

2 Answers

How to configure symbol 5131 through hypertrm


Hi

You can set up the AP 5131 through Hyperterminal by accessing it through COM1 to start,
19200 bits per second
8 data bits
Parity: None
Stop bits: 1
Flow Control: None.

Good Luck. :)

Apr 22, 2010 | Symbol AP-5131

1 Answer

My laptop could not acess the internet


It may because you have a mac filter on. If so you can correct this by connecting to the router then in a Internet explorer type 192.168.1.1 and you should have a configure screen available then either disable the mac filter or enter the other mac adresses. Good Luck

May 27, 2009 | SMC EZ Connect g SMCWEBT-G

1 Answer

I need help setting up the SMC2870W to my gaming system...


You need to run the software provided with the unit. Connect the unit using the provided "crossover" network cable to a PC, this is wired slightly different to a standard network cable so make sure you have the right one - there are many sites that will explain crossover cables and give wiring diagrams.
Go through the setup program and choose the option to use the device as a bridge.

Jan 16, 2009 | SMC2870W 802.11g/b Wireless Bridge

1 Answer

Self-assigned IP address and may not be able to connect to the Internet


if its a wireless network it assigns yyou an ip immediately solong as you are not connecting directly so dont bother about the ip just connect and see what happens.

Oct 27, 2008 | Lucent ORiNOCO AP-500 (8485878380)

1 Answer

Netgear MR314


Chapter 1: Connecting the Wireless-G Broadband Router
Hardware Installation
1. Locate an optimum location for the Broadband Router. The best place for the Broadband Router is usually at
the center of your wireless network, with line of sight to all of your mobile stations.
2. Fix the direction of the antenna. Try to place it in a position that will best cover your wireless network.
Normally, the higher you place the antenna, the better the performance will be. The antenna's position
enhances the receiving sensitivity.
3. Connect a standard Ethernet network cable to the Broadband Router’s Internet port. Then, connect the other
end of the Ethernet cable to your Cable or DSL Broadband modem.
4. Connect your network PCs or Ethernet devices to one of the Broadband Router’s numbered ports with a
standard Ethernet network cable.
5. Connect the AC Power Adapter to the Broadband Router's Power Socket and the other end into an electrical
outlet. Only use the power adapter supplied with the Broadband Router. Use of a different adapter may result
in product damage.

Chapter 2: Configuring the PCs
Overview
The instructions in this chapter will help you configure each of your computers to be able to communicate with
the Router.
To do this, you need to configure your PC’s network settings to obtain an IP (or TCP/IP) address automatically, so
your PC can function as a DHCP client. Computers use IP addresses to communicate with the Router and each
other across a network, such as the Internet.
First, find out which Windows operating system your computer is running. You can find out by clicking the Start
button. Read the side panel of the Start menu to find out which operating system your PC is running.
You may need to do this for each computer you are connecting to the Router.
The next few pages tell you, step by step, how to configure your network settings based on the type of Windows
operating system you are using. Make sure that an Ethernet or wireless adapter (also known as a network
adapter) has been successfully installed in each PC you will configure.
Configuring Windows 98 and Millennium PCs
1. Click the Start button. Select Settings and click the Control Panel icon. Double-click the Network icon.
2. On the Configuration tab, select the TCP/IP line for the applicable Ethernet adapter.
Do not choose a TCP/IP entry whose name mentions DUN, PPPoE, VPN, or AOL. If the word TCP/IP appears by
itself, select that line. Click the Properties button.
3. Click the IP Address tab. Select Obtain an IP address automatically.
4. Now click the Gateway tab, and verify that the Installed Gateway field is blank. Click the OK button.
5. Click the OK button again. Windows may ask you for the original Windows installation disk or additional files.
Check for the files at c:\windows\options\cabs, or insert your Windows CD-ROM into your CD-ROM drive and
check the correct file location, e.g., D:\win98, D:\win9x, etc. (if “D” is the letter of your CD-ROM drive).
6. Windows may ask you to restart your PC. Click the Yes button. If Windows does not ask you to restart, restart
your computer anyway.
Configuring Windows 2000 PCs
1. Click the Start button. Select Settings and click the Control Panel icon. Double-click the Network and Dialup
Connections icon.
2. Select the Local Area Connection icon for the applicable Ethernet adapter (usually it is the first Local Area
Connection listed). Double-click the Local Area Connection. Click the Properties button.
3. Make sure the box next to Internet Protocol (TCP/IP) is checked. Highlight Internet Protocol (TCP/IP), and click
the Properties button.
4. Select Obtain an IP address automatically. Once the new window appears, click the OK button. Click the
OK button again to complete the PC configuration.
5. Restart your computer.
Configuring Windows XP PCs
The following instructions assume you are running Windows XP with the default interface. If you are using the
Classic interface (where the icons and menus look like previous Windows versions), please follow the
instructions for Windows 2000.
1. Click the Start button and then the Control Panel icon. Click the Network and Internet Connections icon.
Then click the Network Connections icon.
2. Select the Local Area Connection icon for the applicable Ethernet adapter (usually it is the first Local Area
Connection listed). Double-click the Local Area Connection. Click the Properties button.
3. Make sure the box next to Internet Protocol (TCP/IP) is checked. Highlight Internet Protocol (TCP/IP), and
click the Properties button.
4. Select Obtain an IP address automatically.
Once the new window appears, click the OK
button. Click the OK button again to complete the PC configuration.

Jul 05, 2008 | NetGear MR314 802.11b

2 Answers

Repeater function


you make a device into ap mode you can get it

Jun 09, 2008 | SMC EZ Connect g SMCWEBT-G

1 Answer

SMC EZ Connect Access Point apparently not connecting to wired router


you doing something wrong there.

give the mac address of smc to the access point that's all you get it

Feb 18, 2008 | SMC EZ Connect (SMC2655W-KIT) 802.11b

Not finding what you are looking for?
SMC EZ Connect g SMCWEBT-G Logo

Related Topics:

704 people viewed this question

Ask a Question

Usually answered in minutes!

Top SMC Wireless Access Points Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18298 Answers

noti13

Level 1 Expert

15 Answers

Mike

Level 3 Expert

4331 Answers

Are you a SMC Wireless Access Point Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...