I've lost my adaptor to my router. I just need to find a place that sells parts.

any power adaptor would do it as long as the voltage is good (usually 12v) and amperes is the same or higher than what's written in your hard drive enclosure (usually 1Ampere = 1000mA) is good enough, some HDDs use up to 2000mA
Usb cable is very easy to find
you can find those at any electronic parts selling or ebay
Please rate

Try to check to this link . I don't actually own router but I hope I helped.

Hi,
The router setup page should be 192.168.1.1
You should be able to access it if you use that address. If you are unsure about your router's ip address, please check my tips and tricks about how to find it out. Click here.
Hope this helps.

Since you say, it is a 12v DC portable Jump starter, the battery inside it is also a 12V battery. You need a 12V charger (eliminator, wall adaptor or whatever you may call it) Regarding current, it could be anything above 500 mA. Better if it is a 1A or 2A or even 3 A depending on the amount you are willing to spend. Now is the most important part. The polarity. I do not know it since i do not have this equipment. Most chances are that you will find (on the RoadPro) a circle and a dot (along with a +VE and -VE marked near it) around where you plug in the adaptor. For most equipments the outer circle is the -ve and the inner dot is the +ve. (unfortunately this could be reversed in some equipments) If you can find this notation on your RoadPro you are lucky. Just go to any electronic shop and buy an adaptor (12V) that matches this circle and dot notation. The same symbol representing polarity will be marked on the adaptor also. Else, you will need the assistance of someone who can check the continuity using a multimeter. This way you can find the polarity. It is pretty easy. Hope this helps.

There are many things that can go wrong with a wireless connection, the main one is interference, many different objects and interfer with a wirless network, if you have a wireless g one then that takes away most of the possible interferences like the microwave, but bluetooth is a major interference, the only to ways of fixing this is to A. get rid of your bluetooth or B. replace your wireless g with a wireless g and n, g and n will ellimanate almost all interferences your current router can sell for a good amount(if you can prove its new and working i suggest you place it back in the box with manual and all) and by a g and n router how that works is it sends out 2 internet signals one g the other n and if one fails like your g then the n will kick in and run most of the internet but again you would have to get a new g and n router and get new wireless g and n software...or you could just not use your bluetooth.

Most stores sell multi voltage adaptors that are quite capable of running routers the only thing you reall need to check are the voltage and current requirements eg. 5 v 500 mA this is usually written on a label on the router either underneath or near where the power supply plugs in.

Any adaptor that meets or exceeds that specification will do then it is just a matter os electing the correct end (they come with a variety) to match your router.

Also check if you need centre positive or negative and set the adaptor to suit this also.

It is usually way cheaper than buying one from the manufacturer and also a lot quicker way to replace almost any pooched power supple that comes in the form of a "wall wart"

Sorry if it sound complicated but I assure you it isnt.

GO TO AN ELECTRONIC PARTS PLACE YOU CAN USALY FIND THEM THERE.
I FOUND ONE AT A PLACE WHERE I LIVE CALLED BAYNESVILLE ELECTRONICS WHERE THEY SELL ALL KINDS OF ELECTRONIC GOODS.
LOOK FOR A SIMLER STOR BY YOU.

No because the VOIP need to be loged in first. if you have the voip first then the wireless router and you turned off the router dchp section part of the wireless modem then perhaps it will work, plus you need a voip account.



I’m happy to help further over the phone at https://www.6ya.com/expert/david_92c86cbc79e9b552

Hi,

Try to put the Internet cable in the Network slot rather than Wireless one.. it will work fine..

most electrical stores sell multi adaptors that work anything take the unit with you so they can check the write way round the power cable needs to be ie the + and - input needs to be the write way round but they should be able to matck you one up for about 5 pound any good hardware store should sell these even some bigger general stores sell them but they wont give you much help getting the write one so i would take it to good hardware store this should solve your prob hope this is some help