Question about SySTOR Systems (400S52) Burner

1 Answer

Oil boiler won't run

I ran out of fuel earlier today, bleed the boiler and it ran 4 5+ hours ... now it was running rough and then stopped. I tried to bleed it 2 more x's ... any tips...

Posted by on

  • 1 more comment 
  • Anonymous Nov 30, 2008

    boiler ran out of oil now wont run

  • glubthesub Dec 01, 2008

    HI,I have a Grant 50/90 Euroflame.I ran out of oil,and it stopped.I refilled,and blead the boiler,but it still will will not fire up.It trys to start,but after 10 sec it shuts down.

  • vbheer Feb 10, 2009

    i have the same problem, ran out of fuel, fill the tank blead the system, then tested the electrodes, there're working, i've tested the nozzle it's working ok, but it still won't fire. HELP!!!


1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

What make and model burner do you have?

Posted on Apr 17, 2008

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Hello I gota samsung dvd writer SE-S084 today. I try to run it on a Mac.I get the error message: "The Device is not accessible, probably because it was removed" Do you have a...

one bad lead will end with a computer error a computer needs its connections continue its cycle and have an end to function!!!!
hope this helps

May 09, 2011 | Samsung External Slim DVD-W USB Compatible...

1 Answer

I have a 2003 Chevy 1500HD 4x4 6.0L, with Airaid air filter kit, throttle body spacer. Stock MAS. I'll drive to work & it will sit 4hours until lunch & when I get in to start it, acts like it has...

I do not know a lot but did you clean the mass air sensor before you put it back in? It may be dirty, or even getting ready to go out. With the new airaid kit and spacer, the MAS may be sending the singnal to the computer that it is overwelmed. You are creating a lot more air flow with the new airaid kit. May even try a more performance MAS, or maybe just clean the stock one real goodwould help. Hope this gives you something to go with, God Bless and good luck.

Mar 24, 2010 | ASUS Z71 (90-N9Q1G1000) (90N9Q1G1000)...

1 Answer

02 vauxhall combo 1700cc ran out of diesel refilled but will not start

Bleed the fuel filter by un doing the small bolt at / near top of the fuel filter and hand pump (If fitted) till diesel squirts out.

Mar 12, 2010 | Enlight Combo (5601908) (Beige) (5601908)...

1 Answer

Vauxhall combo epic 1.7 Y(01) battery light

the yellow relay is a red herring,its the glow plug relay just clicking as the current is trying to find another path to earth,id say its a dodgy regulator on alternator, but possible the light goe through the time circuit of the relan start up but id suspect regulator,

Feb 04, 2010 | Enlight Combo (5601908) (Beige) (5601908)...

1 Answer

I need to purchase a new oil boiler. which is better with hard water,, cast iron or steel. or is there no problem with either

i am told that with time the cast iron boiler will have problems due to the ph of the hard water, therefore the steel boiler is recommended.

Nov 18, 2009 | SySTOR Systems (400S52) Burner

1 Answer

Oil went too low, now don't start

There is a bleed screw on the pump, turn a 1/4 turn to the left, and bleed until oil is free of oil. On older pumps, instead or a bleeder valve it is just a plug, you will have to remove the plug, bleed, then replace the plug

Apr 06, 2009 | SySTOR Systems (400S52) Burner

1 Answer

Burner will run for a couple of hours and then turn off.

They could have disturbed the sludge in the tank when refilling. If you do not have a filter in place it may have clogged the pump or jet and making it hard to start. These need yearly maintenance anyway. The pumps usually have a screen inside and the jet has a screen inside. First,open the bleed on the pump and purge some oil from the line and see if it is flowing freely. If so, the take the drawer assembly out and clean it. Make sure the jet is clear, by blowing through the attached oil line. You should see/feel a fine mist of oil come out. Electrodes should be about 5/32" apart for an F5.

Jan 14, 2009 | SySTOR Systems (400S52) Burner

2 Answers

Burner will not light

you need to tell me what the burner is doing when it starts up. Some basics to look for:
1- bleed pump of any air- is it a new install? 2- If you are getting fuel, are you getting spark on the electrodes? 3- if you are, you may need to adjust draw assembly air, and or air intake per Carlin specs.

Jan 02, 2009 | SySTOR Systems (400S52) Burner

3 Answers

Riello oil burner

i have a reillo oil burner that fires up from cold no problem reaches the set temp and cuts out, when it tries to kick back in it keeps clicking the lockout light is not coming on and the fan is still running any ideas?

Oct 08, 2008 | SySTOR Systems (400S52) Burner

Not finding what you are looking for?
Computers & Internet Logo

Related Topics:

1,430 people viewed this question

Ask a Question

Usually answered in minutes!

Top SySTOR Systems Computers & Internet Experts

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers


Level 3 Expert

98816 Answers

David Payne
David Payne

Level 3 Expert

14071 Answers

Are you a SySTOR Systems Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides