Question about Asko W6021 Front Load Washer

1 Answer

Door gasket i need to replace door gasket on my washer,it is about 12yrs old. thanks parnell

Posted by on

  • 1 more comment 
  • fixiechic Feb 23, 2008

    A repairman replaced the door lock last October. Now I am getting a leak from the door itself, on the lower section. Does the gasket need replacing? If so, can I fix it? Otherwise, I get "hosed" by the official repair geeks.

  • parny Mar 06, 2008

    the gasket is on the machine,not the door. model #8005

  • fixiechic May 11, 2010

    My gasket sits on the door, model W620. I found the information helpful in  that I'll change the door out instead of playing with the gasket. However, I wan to know how to change the gasket as well as the door. Does anyone know where to get their hands on  a bonafide service manual without resorting to confiscatory practices of service people? Thanks



1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.


    An expert that has over 500 points.

  • Expert
  • 351 Answers

You will find it will be better to change the whole door,you can get the seal but its a fiddly job.

Posted on Mar 02, 2008

  • Ian Greenland Mar 07, 2008

    use a screw driver at the bottom of the door and remove the outer door skin then you will find screws that hold the glass in remove them and the door glass will come out .if use some soap on the new seal it will go in a bit easier,but will still be harder than replacing the door.the door seal on the new doors is a better design than your model.I have replaced several door gaskets on asko's and its not always very successfull.Goodluck



1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

My Kenmore 800 series washer is leaking water all over the floor and i can't find where its coming from. It only leaks when its on and running. I tried to take the back of it off to see where it was coming...

Some of theses models have a tendency of leaking out the side of the pump housing. In this case you will need to replace it. Here is a link to help disassemble and acess the pump.

Disassembling a whirlpool style washer

Oct 13, 2010 | Kenmore 22422 Top Load Washer

1 Answer

Broken door on simpson maxidry 362

when it comes to whitegoods old is good. your dryer will outlast most new ones. buy the new parts it will b lot cheaper than a new dryer. not much goes wrong with the old simpsons. please reply if u need more help

Apr 11, 2010 | Dryers

1 Answer

First: Loud Banging Noise. Now: No spin cycle.

Sounds like it may have been overloaded, or unblanced, I would say it would be better to can get pricey if the first fix doesn't work. Washers don't cost what they use to, get a scratch and dent sale item and save money too!

Aug 09, 2009 | Washing Machines

2 Answers

40 gal 12yrs old ,has evac sys.flame comes on for sec.,shuts down

most likely a flame sensor problem.remove fl sensor , clean with steel wool or fine emery cloth,replace and it should solve yor problem

Jul 20, 2009 | Rheem Tankless Water Heater Manifold...

1 Answer

Changing the door gasket on Hotpoint Ultima WD860

Managed to work it out myself how to take the old door gasket off and attach the new one. Thanks. Machine working okay with no leaks or mould anywhere now.

Apr 07, 2008 | Hotpoint Ultima WF860 Front Load Washer

4 Answers

Bosch front load needs new gasket

Bosch WFMC 3200 Front Load Washer needs to replace
door gasket.
This video will show you how to change a door seal or gasket on this Bosch front loader washing machine and also where to buy parts!
we have all bosch repairs in our channel.

Please remember to subscribe to our YouTube channel for all appliance tutorials

a 4 THUMBS rating is appreciated for answering your FREE question.

Feb 22, 2008 | Bosch WFMC 3200 Front Load Washer

Not finding what you are looking for?
Asko W6021 Front Load Washer Logo

Related Topics:

143 people viewed this question

Ask a Question

Usually answered in minutes!

Top Asko Washing Machines Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1474 Answers

Oloyede Monsuru

Level 3 Expert

1417 Answers

Are you an Asko Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides