Question about GE JKP15 Electric Single Oven

1 Answer

Ge oven fuse

I need to replace the fuse for an F3 error on my electric oven and i cannot locate where the fuse panel is

Posted by on

  • rjwecker Apr 27, 2008

    bake doesn't turn on broil o'k as is everything else but bake button does nothing at all

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • GE Master
  • 2,651 Answers

Checkin model # jkp15, f3 shows up as a shorted oven sensor here, No fuse even shows up for this particular model

Posted on Feb 23, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I turn the oven to 350 and in five second's it beep's and we get a f3 and sometimes f7 this is very frustrating! I take the over off and play with the wires and put it back together and sometimes it will...


I will give you the meaning of the error codes and possible solutions.

F3 Open Sensor circuit, Open (blown) sensor fuse or bad sensor.
More than likely, you have a oven sensor that needs to be replaced.

F7 Problem with the keypanel, possibly, a function pad button is stuck.
Attempt to clean and unstick button. If this fails, you may have to replace the
keypanel.

I hope this helps you

Feb 02, 2011 | GE JKP15 Electric Single Oven

1 Answer

My ge oven model # J RSO4BOW3 is showing a error code F3 and F5


F3
or
F4 Open or shorted oven temperature sensor (RTD) Check sensor harness and harness connection between oven sensor and oven control. Replace oven temperature sensor (RTD) if wiring is ok. F5 Loss of relay drive circuit If this fault code cannot be cancelled, replace the oven control (also called clock or ERC).

Oct 30, 2010 | GE JRS04 Electric Single Oven

1 Answer

Error


F3
or
F4 Open or shorted oven temperature sensor (RTD) Check sensor harness and harness connection between oven sensor and oven control. Replace oven temperature sensor (RTD) if wiring is ok.

Dec 18, 2009 | GE Profile JTP56 Electric Double Oven

1 Answer

The oven isn't working and it says FO in red letters


GE / Hotpoint / RCA
Oven Fault Codes
Display Condition Remedy
F0 & F1 Failed Thermistor Control Replace ERC
F2 Oven Temp Exceeds 590 with unlocked door High resistance in Sensor, likely a bad sensor
F3 Open Sensor circuit Open (blown) sensor fuse or bad Sensor
F4 Shorted wire or Sensor locate short and correct it
F7-A Function pad button stuck Clean and unstick
F7-B Bad Clock Replace Clock
F8 Electrical component failure Replace ERC
F9 Program with door circuit Check wiring

Frigidaire / Westinghouse / Tappan / Gibson
Oven Fault Codes
Display Condition Remedy
F0 & F1 EOC failure Replace EOC
F2 Oven over heat Defective Sensor or EOC
F3 Oven Sensor Open Replace Sensor
F4 Shorted wire or Sensor locate short and correct it
F5 EOC failure Replace EOC
F6 EOC failure Replace EOC
F7 EOC failure Replace EOC


Maytag / MAYCOR / Magic Chef / Jennair / Admiral
Oven Fault Codes
Display Condition Remedy
F0 Function key shorted or stuck button Clean and unstick button or replace Touch Pad or Clock
F1 Defective Touch Pad or Membrane Replace Touch Pad or Membrane
F2 Oven over heat defective Relay Board or (if present) or defective Sensor
F3 Oven Sensor Open Replace Sensor
F4 Shorted wire or Sensor locate short and correct it or replace Sensor
F5 Hardware, safety circuits disagree Replace Clock
F6 Missing AC (power) signal Check for proper voltage (plug, breaker, etc.)
F7 Function key shorted or stuck button Clean and unstick button or replace Touch Pad or Clock
F8 A/D Warning Replace Clock
F9 Door Lock Warning Check door lock circuit or Replace Clock


Amana / Caloric
Oven Fault Codes
Type with display - glass link ERC
Display Condition Remedy
F0 No Safety Signal Replace adapter board
F1 No Safety Signal Replace ERC
F2 Oven over heat Replace defective Sensor
F3 Oven Sensor Open Replace Sensor
F4 Shorted wire or Sensor locate short and correct it or replace Sensor
F7 Shorted Touch Panel Replace Glass Panel
F9 Door Latch Error Check latch
FF Lock Error Check switch and motor
ERC III - Relay board with separate board/push buttons
F0 Shorted Push Pad Replace Push Pad
F1 Defective ERC Replace ERC
F2 Oven over heat Replace defective Sensor
F3 Oven Sensor Open Check/Replace Sensor
F4 Shorted wire or Sensor locate short and correct it or replace Sensor
F5 Defective ERC Replace ERC
F6 Defective ERC Replace ERC
F7 Shorted or sticking button Clean button or replace touch pad
F8 Defective ERC Replace ERC
F9 Door Latch Error Check latch


The following diagnostic chart Does not apply to Whirlpool 'Y' line products. If the model number contains a Y near the end of the number, DO NOT use this chart.
Whirlpool / KitchenAid / Roper
Oven Fault Codes
Ovens with 4 digit displays
Display Condition Remedy
F0-E0 Analog to Digital failure Disconnect panel for 30 seconds. if error re-appears then replace control
F1-E1 Defective ERC Replace ERC
F2-E0 Shorted Keypad Replace Keypad
F3-E0 Sensor or Sensor Fuse Open Replace Sensor or Fuse
F3-E1 Shorted wire or Sensor locate short and correct it or replace Sensor
F3-E2 Oven over heat Replace Sensor
F3-E3 Cleaning Temp over heat Replace Sensor
F5-E0 Door Error Check Door
F5-E1 Door Latch Check Latch
F5-E2 Door Switch Check Switch
Ovens with 2 Digit Displays
F0 Defective ERC Replace ERC
F1 Defective ERC Replace ERC
F2 Oven over heat Replace defective Sensor
F3 Oven Sensor Open Check/Replace Sensor
F4 Shorted wire or Sensor locate short and correct it or replace Sensor
F5 Defective ERC Replace ERC
F6 Problem with time keeping circuit Reset Time or cooking operation and check for proper ground
F7 Shorted or sticking button Clean button or replace ERC
F8 Defective ERC Replace ERC
F9 Door Latch Error Check latch and latch circuit

Dec 18, 2009 | Ovens

1 Answer

F2 and F3 error codes in GE electric wall oven


Call GE answer center 1-800-626-2000 ask for tech help, Have you Model # off you data plate ready.

May 09, 2009 | GE JRP15 Electric Single Oven

2 Answers

GE Oven displaying both F2 and F3 error codes; bad ERC or temp sensor?


F3 is Open oven temperature sensor circuit.
F4 Shorted oven temperature sensor circuit .
F7 Component failure.

To fix this you need to read oven temperature sensor circuit at oven temperature sensor ( approx 1000 ohms at room temp); check for cut or pinched wire or loss of contact, if wirings are ok, then replace the probe.

Oct 28, 2008 | GE JRP15 Electric Single Oven

1 Answer

F3 Error Code - GE Electric Oven JTP18


all ge codes f3 are saying ot replace thermal sensor, you can check the harness connecting them for a pinched or burnt wire i guess, as far as getting a part number , you can enter complete modle number her e and look for the sensor, i checked just the partial number you gave and a few different ones showed up
http://www.searspartsdirect.com/partsdirect/index.action

Apr 22, 2008 | GE Profile JTP18 Electric Single Oven

3 Answers

F3 Error


This is due to a Defective control board..You have to get it replaced..

Oct 15, 2007 | GE Profile Advantium SCB2001KSS Stainless...

1 Answer

GE Model JTP15 oven shows F3 error code


I have the same problem. I noticed that the oven gets to the selected temp ok. Then when the pilot attempts to RELIGHT, it gets the error F3. Did you get a solution? After other posts, I will see if the temp sensor is around 1100 ohm as suggested by others. Ken

Jun 14, 2007 | GE JTP15 Electric Single Oven

Not finding what you are looking for?
GE JKP15 Electric Single Oven Logo

Related Topics:

482 people viewed this question

Ask a Question

Usually answered in minutes!

Top GE Ovens Experts

William Miller
William Miller

Level 3 Expert

8820 Answers

Michael Thomas
Michael Thomas

Level 3 Expert

3051 Answers

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Are you a GE Oven Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...