Question about Car Audio Receivers

2 Answers

Wiring a in-dash cd player in my89 honda accord

  1. the wiring of the cd player is not the same as the factory wiring

Posted by on

  • Anonymous Mar 28, 2008

    The wiring in my 94 Blazer are also not the same.How do I install?

  • Anonymous May 27, 2008

    WIRING harness for jensen model cd2620se

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Buy a factery car stero adapter

Posted on Apr 24, 2009

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 11 Answers

About all I can tell you is to start splicing and see what goes where, figure out all the power and the grounds by elimination. Then starton the speakers.

Posted on Feb 23, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need to know how to install a cd player in my 1997 jeep wrangler sport.


My suggestion would be to buy a wiring harness and a dash mounting kit. After that unscrew or pull out the console/dash part thats around your factory deck. Then unscrew the bolts/screws holding the factory one in place. Remove it. Plug the wiring harness into the factory wire plug. Pull harness wires through the mounting kit. Attach the corresponding colored wires from the harness to your new deck. Slide your deck into the mounting kit and secure it in place. Most decks have little prongs that you can pry up to **** up against the mounting kit so it wont slide out without pushing those down (makes it more secure and harder to steal). Place deck with mounting kit into area factory deck was. Put the screws/bolts back into place tightly. Place console/dash part back on. You will need the mounting kit (99% of new decks are smaller than the factory). Wiring harness is optional but recommended.

Jun 22, 2010 | Panasonic CQ-C7105U CD Player

1 Answer

94 Honda Prelude Factory Car Stereo/CD Player


The BUS wires are a serial data link, probably incompatible with other makes of CD player. I'd hesitate to connect it to +12v, this may cause damage. If anything try connecting it to BUS.C through a 1kohm resistor to start with.

Perhaps you need something like this to make it work. http://www.caraudiocentre.co.uk/product_m-alpine-kcm-122b_p-20941.htm

 

 

Oct 21, 2007 | Car Audio Receivers

1 Answer

No sound dual xhd6420 92 accord lx


my brother has a 1993 Honda accord and had the same issue, we put it different speakers and it worked fine, don't know what the problem was but it worked

Feb 12, 2010 | Dual Electronics XHD-6420 CD Player

1 Answer

My honda accord 2006 model has a 6 stacker in dash cd player. the button to select the cd player is marked cd/aux, does it have an auxilliary input?


No, but you can add different items such as a satellite radio, hd radio, or auxiliary hook up, through the same port.

Oct 15, 2009 | JVC KD-LH7R CD Player

1 Answer

Installing a cd player in a 1992 honda accord


The harness looks like what is depicted on this link: http://cgi.ebay.com/JVC--16-PIN-WIRE-HARNESS-FOR-CD-PLAYER-BLACK-BRAND-NEW_W0QQitemZ370214069143QQcmdZViewItemQQimsxZ20090612?IMSfp=TL090612198008r8862
This connector fits the following JVC Car Radio/CD/MP3 Players with 16 pin connection.
All wires are labeled.

Hope this helps....................sodeep

Jul 26, 2009 | JVC KD-G220 CD Player

1 Answer

How to connect a pioneer super tuner to a 91 honda accord


With a DC voltage tester, check the two power leads for 12+ volts and proper operation, and be sure the unit is properly grounded.

The two power leads are,

1.Constant feed: which should be connected to an un-switched power source that delivers continuous
power to the units memory.

2.Switched feed: which should be connected to a switched power source controlled by the vehicles ignition switch.

Before installing in dash check unit for proper operation.

Good luck
Aduz

Mar 27, 2009 | Pioneer DEH-P2900MP CD Receiver...

2 Answers

Trying to install after factory radio in 94 Honda accord ex and can't get any sound


I have a 93 accord ex with the bose amp system. Had a Sony deck put in it. It had the popping and the noises. It was installed at a store and they had to hook the red power wire to the antenna wire to get the sound to come out of the system when playing a CD. I thought that was bogus to have the antenna up all the time so I took it back out and put another quick hookup harness in it and it did the same thing. Will not put out any sound till the red power wire is hooked up to the antenna wire so that it goes up when the key is turned on. Installed the same stereo in a 94 taurus SHO with amp and it worked great. I believe that there is an expensive kit that converts the bose system to hook up a unit so that it doesn't pop click buzz, and have to have the antenna up to play.

Jun 19, 2008 | Car Audio Receivers

1 Answer

Replacing car radio


you need to get a wiring conecter kit. the directions will be in the box. i just got mine today and had to get one of those kits... walmart has them =P

Dec 24, 2007 | Car Audio Receivers

Not finding what you are looking for?
Car Audio Receivers Logo

Related Topics:

308 people viewed this question

Ask a Question

Usually answered in minutes!

Top Car Audio Receivers Experts

xxxxxx xxx

Level 3 Expert

4706 Answers

yadayada
yadayada

Level 3 Expert

61037 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Car Audio Receiver Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...