Question about Projection Televisions

1 Answer

Dura brand bh2004d will not come on custamer said lighting hit it but the fuse was not blown.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 319 Answers

If the TV was not on a surge protector during a lightning strike there could be more wrong than just a fuse. Any number of components could have gone I.E. capacitors, relays, or transistors. Unless you have extensive troubleshooting skills down to the component level...i would just call it a loss.

Posted on Feb 22, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

TV Wont turn on after lighting storm. I have tried to; unplug and plug back in. Unplug it for 24 hrs. Try different outlets. Look at the build, looks fine.


The TV circuitry is designed to protect from power surges. The fuse on the power supply may be blown, or the power supply itself could have taken a hit. I would try to check the fuse first and then if it turns back on... it did it's job!

Good luck! and let me know what happens!

Oct 12, 2010 | Panasonic PT-52LCX66 Projection Television

1 Answer

Duraing a power outage my tv went off and now will not come back on no power to it at all. everything is ok cable box is on , stero is on.Is ther a reset button for the tv?


Is your TV's indicator light ON? Did you try turning it on from the remote as well as from the TV's control panel?
If your TV's indicator light doesn't come ON, it could be that the fuse inside has blown due to the power fluctuations. If indicator is ON, your TV's internal power supply seems to be fine, you may have to take it to your technician.

Jan 09, 2010 | Toshiba 55H70 55" Rear Projection...

1 Answer

The green timer light flashes when i plug in the tv, after hitting power the timer light comes on for about 4 sec then goes out. Tv does not power up, the error code it blinks is 2 blinks a pause and 2...


MODEL NUMBER WT-46809:

2,2 is the error code for short protection.


The most common reason for this is one of the 2 pico fuses that protect the convergence circuit is blown. Changing the fuses will not help! They are green in color and soldered into the middle circuit board and are F9a04 and F9a05----look like resistors but are 5 amp fuses.

99% chance if one or both are blown---you have to have someone change the STK-392-570 convergence IC'S that this set uses----the IC'S can be purchased on Ebay for under 14 dollars and the same seller sells the pico fuses 5 @ 2.95.

The best thing to do here if you or someone you know is able is to unplug the set and look for the fuses---middle board towards the back---there are 5 of them and the two closest to the back of the row are for the convergence IC----If someone checks them (like testing any other fuse) you will know--if either or both is blown--the convergence IC got them.

I have start to finish, step by step instructions and photos of the fuses etc----If you or someone you know can solder and is handy--you may be able to do the repair yourself.

If not, shops usually charge 300-400 for this kind of repair in this set.

LET ME KNOW IF YOU NEED ANY ADVICE or help.

Regards, SD TECH

Oct 28, 2009 | Mitsubishi WT-46809 46" Rear Projection...

1 Answer

My 62 inch mitsubishi tv was hit by lighting


Try to find a local repair centre & ask if they can give you an estimate on the cost to repair. A lightning strike can cause either minor damage such as just an internal fuse blown or can cause severe damage which will wipe out entire circuit boards which can be a costly repair. In this case it's usually not worth repairing.

Oct 07, 2009 | Mitsubishi WD-62525 62" Rear Projection...

2 Answers

Tv dead power through on/off switch


yes there is a fuse.that is located on the main board.and that fuse is mostly blown and needs to be replaced. you can get new fuse at  www.radioshack.com at the rate of $2.

May 05, 2009 | Projection Televisions

1 Answer

Ws-65315 won't turn on


Need to know more, 1-2 is no error code, you say will not turn on, do it has led light on or do you hear sound in set like high voltage? Any lights blinking? Or just completely dead, like fuse blown?

Mar 24, 2008 | Mitsubishi WS-65315 65" Rear Projection...

Not finding what you are looking for?
Projection Televisions Logo

Related Topics:

65 people viewed this question

Ask a Question

Usually answered in minutes!

Top Projection Televisions Experts

Jaime Hernandez

Level 3 Expert

2267 Answers

matt martin
matt martin

Level 3 Expert

1191 Answers

yadayada
yadayada

Level 3 Expert

60769 Answers

Are you a Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...