Question about Jensen VM9510 Car DVD Player

1 Answer

Is there a way to keep the screen out?

I wanted to know if there is a way , if you wanted to , keep the sceen for going in and out>? to limit moving parts?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

The code is a permanent way of disabling the brake override on the jensen units.


There are two ways of doing this:

Insert the DVD

After the disc loads and plays you will see a blue screen telling you "it is unlawful to drive with a movie blah blah blah"

1)Activate the brake sequence and disable the blue screen using the hand brake, the switch method or anything else to give the unit its three pulses to disable that freakin blue screen.

(What I did was I installed my radio entirely, then took the pink wire and touched for two seconds, removed for two seconds and then touched and held the negative pole of a mower battery laying on my passenger seat until the screen was no longer blue.)


2) Next, on the main remote press stop twice, then 1, 2, 6, 4.

You will now see a hidden menu that says:

Region Code
Brake Override (I know you're drooling by now)
Macrovision (Watch all the burned and pirated movies you want if this option is off)
Loader Version
Model Version


3) Using the right joystick on the unit, navigate to the options of your choice, click on them to toggle on, off or which region code you want.

This is what you want:

Region Code: 1
Brake Override ON
Macrovision: OFF

When your done, click SYS SETUP on the main remote TWICE to save the settings and bingo, your done!!! Hooray!!! You can now kill your whole family in the car while watching that adult movie while your driving.....


The other way of doing this is by not engaging the parking brake sequence, thus you're inputting the code blindly.

1) Insert the DVD and you'll get the blue screen.

(If you have more than one tv, the unit itself will have the blue screen but the additional tv's you have plugged in will NOT, they will show the dvd menu. Thus you will be able to see the hidden menu on the additional screens after inputting the code, but not on the main unit because of its blue screen.)

2) On the main remote, push stop twice and then 1, 2, 6, 4

3) Push the joystick on the unit SOUTH twice and then click it once.

4) Press SYS SETUP on the main remote twice to save your settings.


It may take a few tries but you'll get it. This method can be done if you don't want to bother temporarily activating the brake sequence, but if you only have the unit and no additional tv's, its #$%^&* damn hardbecause you can't see the settings your changing.


I tried to make this as clear as possible. If you have questions, private message me or post here.

This code DOES work.

Best of Luck!


By the way, this is for informational purposes only and I will not be responsible for anything bad/stupid/ignorant you do with your Jensen unit.

Posted on Apr 23, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to remove speed limiter


If you don't live in California you can buy a tuner from SCT,Superchips or most other brands that will raise your speedlimiter

Aug 19, 2014 | 2007 E250

1 Answer

My ray pak water Hester is going on and of


Check your "unitherm governor", it's the thermostat that allows some water to bypass the heat exchanger. It looks a lot like a car t-stat and is located in the header where the plumbing attaches.It sounds like most of the water is bypassing your exchanger.That may also explain why the hi limit keeps kicking the heater off, because the water in the exchanger is not moving through fast enough and overheating.
Please reconnect the hi limit, as it is an integral part of the "safety loop". That's the series of switches and sensors that keep the thing from exploding. Your hi limit was doing its job.
Hope that helped, good luck.

Jan 26, 2013 | Raypak Rp2100 Pool & Spa Heater Lonox 407k...

1 Answer

The shifter will not move into the # 3 range on the front derailluer, problem is in the shift lever


Check the limit screws. It is likely that the limit screw is adjusted to keep the movement limited to the first two chainrings. If that is not the problem, alignment or damage may be the source.

Jan 07, 2011 | Mountain Shimano Alivio Front Bike...

1 Answer

Thermal fuse keeps blowing. Dryer heats up too


The problem will be either your vent is stopped up or the cycling thermostat and the high limit thermostat are bad. If the vent is clean, both the cycling thermostat and the high limit thermostat are welded closed. Both are supost to open to avoid over heating. Go to www.partselect.com and enter your complete model number. It will bring up diagrams of you machine. From there you can find the parts ans also order them if you want to. Good luck.

Nov 25, 2009 | Cars & Trucks

1 Answer

Chamberlain Liftmaster bounces back up sometimes...


On the side of the motor unit you will find the 'down limit control'. Using a small screwdriver turn this control in the opposite direction of the arrow printed on the cover. Some tweaking will most likely be necessary. You can remove the cover and watch the limit switch assembly and get a good idea how it works.

Sep 30, 2009 | Sears Craftsman LiftMaster Chamberlain...

2 Answers

Lcd touch sceen needs resetting it is misalinged


you get to the touch sceen by holdin down the frist tow buttons and turning the machine on the singer sceen will turn on just touch the sceen and you will see a small black box touch the box and it should move touch it four times and then touch the stright stiche white button at the bottum of the sceen it will save the settings and it will work .

Jan 14, 2009 | Singer Quantum XL-1000 Computerized Sewing...

1 Answer

Mouse, cursor and scrolling problems


HI TRY CHANGING DISPLAY SETTING IF YOU THING IT THE DISPLAY 

Dec 03, 2008 | HP Pavilion Media Center a1330n - AMD...

2 Answers

Volume Limit


Press settings.

Press Volume Limit.

Move the wheel around to desired position.

Press the center button.

If you don't want to set a combination, press done.

Jul 01, 2008 | Apple iPod nano

Not finding what you are looking for?
Jensen VM9510 Car DVD Player Logo

104 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jensen Car Audio & Video Experts

xxxxxx xxx

Level 3 Expert

4917 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

The Knight
The Knight

Level 3 Expert

75178 Answers

Are you a Jensen Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...