Question about NEC NP40 Projector

Open Question

Np40 PJ Wont Start Blinking Status Light

NEC Np40 DLP Projector Wont Start, Status light blinks x 8 orange... Please Help.

Posted by on

  • www_snake666 Feb 12, 2010

    Cooling Pump was damaged, thanks for no help :P

  • mitran Dec 29, 2011

    Where did you order a new cooling pump? I can't find a shop where the sell one.

×

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: NEC MT1050 pojector

you are right about the filters. It turned out that the projector was slightly damaged and there was a filter trigger that was not being pushed in and was not allowing my projector to turn on. Had to have that disconnected by a professional so that the projector would work.

Posted on Jan 15, 2008

SOURCE: Lamp will not come on

try pressing and holding the enter button on the projector for about 30 seconds - this resets it. It worked for me!!

Posted on Feb 20, 2008

Gigatech
  • 259 Answers

SOURCE: Status light blinking red

If it is a lamp error try this:
When the lamp exceeds 2100 hoursof service, the projector cannot turn on and the manu is not displayed. Do the following:
For VT670/VT470 Press the help button on the remote control for a minimum of ten seconds.

For VT570/VT47 Press and hold the power and the exit buttons on the remote control simultaneously for a minimum of ten seconds. When the lamp time clock is reset to zero, the lamp indicator goes out. Hope this helps! :]

Posted on Feb 27, 2008

SOURCE: No Picture on my nec VT676 model

Thanks. NEC did not have a solution for us, but the solution for us was to replace the bulb. You'd think they would make that a bit more obvious!

Thanks.

Posted on Mar 27, 2008

Gigatech
  • 259 Answers

SOURCE: Blinking status light

6 cycle (0.5 sec On,
0.5 sec Off) is a lamp error!
0.5 sec Off)
Lamp fails to light. Wait a full
minute and then turn on again.
Even though the lamp is not old there may be a defect in the lamp. I know the lamps are expensive but this may be the problem. If you have a lamp that was removed due to age but still worked you could use the lamp to test it.here is a link to the user manual:
http://www.iusb.edu/~libg/ims/VT570_MAN.pdf

Hope this helps. :}

Posted on Apr 02, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have an NEC LT380 projector just changed bulb but, now it powers on then back off and i get 6 flashes on the status light. Any help would be great since this model is no longer made.


http://www.nec-pj.com/dl_data/lt380_manual_e.pdf

Scroll to page 107 and read through the various light blinking codes. This will help you figure out exactly what the blinking light error is and what steps are needed to correct it. If you are still having trouble please respond with further information for more in depth troubleshooting.

Jan 27, 2016 | NEC Office Equipment & Supplies

1 Answer

When I hit the start button on my NP 115 it begins to sound like the fan labors and pulses until it shuts down and the red light blinks in a series of 6 blinks. It also has a very hit frequency squeak that...


after 5 minute image go out n power indicator steady light orange n status indicator red light blikns in a series of 6 blinks. in the manual book said lamp error.. what mind "lamp error". please help me.

Jul 28, 2011 | NEC NP115 DLP Projector

1 Answer

I have a NEC VT470 Projector. The power light is steady orange and the status light blinks red 6 times.


steady orange means projector in standby mode
red light 6 times is a lamp error.
either the lamp is old and wont start up or the ballast power pcb is not working.
can you hear the sparking of the high voltage trying to strike the lamp.
if you can then the lamp may be dodgy.
can you borrow one to test it out

Mar 02, 2011 | NEC VT470 Multimedia Projector

1 Answer

My nec vt595 wont start up the status light is flashing orange


The only time the "status" light will be orange is when you accidently press the cabinet button and the cabinet is locked.

However, if the "power" light is blinking orange it means that the projector is cooling down and you need to wait a few minutes.

Jan 03, 2010 | NEC Computers & Internet

1 Answer

Status lamp blinking orange 6 times


PROJECTOR. NEC VT491 THE STATUS LIGHT IS BLINKING 6 TIMES RED, AND THE POWER LIGHT IS ORANGE

Jun 26, 2009 | NEC Office Equipment & Supplies

2 Answers

NEC VT 595 wont turn on. Just red blinking light


I had this same problem with 2 NEC VT595 projectors. My problem was that there was a broken "tab" on the lamp cover (the plastic cover that slides in place over the lamp) that is supposed to depress a switch which insures the lamp cover is in place before operating the projector. The tab was broken in half and not making the connection there for causing the blinking status light (.5 sec on, 2.5 sec off) indicating a lamp housing or cover error.

May 28, 2009 | NEC VT595 LCD Projector

2 Answers

Nec projector


Please contact at
It gear. In
Shop no 14, Sakhai plaza,
Nr. Kothrud Tel. Exchange,
Kothrud, Pune, India. Land mark- Shree Shivaji Statue. Telephone -020-66021475, Hand Phone - 9850557001.
Contact person- Ketan
www.itgear.in

Apr 03, 2009 | NEC NP02LP Replacement Lamp for NP40/NP50...

2 Answers

Lamp not lighting


Reset the lamp and try it.

Mar 28, 2008 | NEC VT660 Multimedia Projector

2 Answers

Lamp will not come on


try pressing and holding the enter button on the projector for about 30 seconds - this resets it. It worked for me!!

Feb 10, 2008 | NEC VT460 Multimedia Projector

Not finding what you are looking for?
NEC NP40 Projector Logo

Related Topics:

520 people viewed this question

Ask a Question

Usually answered in minutes!

Top NEC Office Equipment & Supplies Experts

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

The Knight
The Knight

Level 3 Expert

74106 Answers

Piyal Perera
Piyal Perera

Level 3 Expert

528 Answers

Are you a NEC Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...