Question about Lands Phones

7 Answers



Posted by on

  • 4 more comments 
  • markthedoc Feb 28, 2008

    have tried to pair my bt28vm with a new nokia phone-does not seem to recognize the headset,although it does recognize my old nokia phone

  • robert hitchcock Mar 19, 2008

    ok got a soloution

    turn bluetooth headset off

    press all 3 buttons at once

    the unit will turn on and after 2 seconds will enter pair mode

    search for headset on phone

    passcode 0000

    the unit is now paired

    good luck


    please email me @ if u have any other problems with devices.....

  • swaffybeag Apr 03, 2008

    Problem is I can't hear the other person but they can here me fine, tried adjusting the volume but still not working........weird, any suggestions?


  • mynameistom Jun 12, 2008

    bought the opticom bt28vm today and couldnt wait to use it, followed instructions and will not pair with my nokia xpress music phone. i have already tried Robs solution but just doesnt do anything. can anyone help??


  • Penelope P Jul 16, 2008

    I had the same problem connencting it to my Nokia N95 and after many frustrating attempts it finally works. The solution was to hold the three keys down for quite some time on the headset until the light flashed alternately between red and green (ie blinking), and hey presto, there you go, you just need a little more patience lol. Good Luck guys, hope it works for you too.

  • Anonymous Oct 24, 2008

    i cant Pair my BT28vm with my moto Razer V3i

    it is showing that "no new device is found"

    plz suggest what can i do????


7 Answers

  • Level 1:

    An expert who has achieved level 1.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 1 Answer

I have this one and it works in a different way so this may help everyone struggling.

1. Turn off the earpiece if it isn't already on
2. Press and hold the power key - when it comes on in about 5 seconds, keep pressing the button
3. About 3 seconds later, the light should change from a steady pulse to a solid light, you can then release your by-now-sore finger
4. Start searching for the device on your mobile (or other device)
5. Pair it when found (if this doesn't happen automatically) and enter the passcode 0000 when prompted.
6. All done

Hope this helps those struggling with Rob's solution,


Posted on Nov 21, 2008

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

How do i knock my bt28vm headset off mute

Posted on May 17, 2009

Mine showed blue and then it blow up

Posted on Aug 29, 2008

Mine showed blue and then it blow up

Posted on Aug 29, 2008

Turn it off, then press the volume and power buttons all at the same time, it will flash orange (to show that it has turned on) after a couple of seconds, keep the buttons held in and after a few more seconds it will flash red and orange, slowly, now search for your device on your phone.

Posted on Jun 15, 2008


Posted on Jun 01, 2008

If you turn it off then hold the power and volume buttons it will start flashing red and green then start looking on your mobile and you should find it

Posted on Apr 24, 2008

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Phone manual opticom

Call forwarding is a service offered by your telephone company, and the procedure varies from company to company. Please contact your telephone company for their instructions regarding call forwarding.

Sep 06, 2013 | Lands Phones

1 Answer

Phone manual opticom 300

Contact Opticom directly for information

Jun 11, 2013 | Lands Phones

2 Answers

My dad has lost his manual for his opticom B300 phone and want to know how to put numbers in for speed dial can you help

This is how to store a quickdial number on the Opticom B300

1. Lift up the handset.

2. Press the STO button (for 'Store')

3. Key in the full number you want to store, e.g. 01234 5678910

4. Press STO again

5. Press one of the numbers on the key pad that you want to be the Quickdial number, from 1 to 0

6. Press the MEM (Memory) button.

7. Replace the handset in its cradle.

8. The Quickdial number will now be stored and you can call it by lifting the handset (or pressing the speakerphone button) and then pressing the MEM button followed by the single number you chose.

May 29, 2011 | Lands Phones

2 Answers

How to retrieve answer phone messages

try pressing intercom 777 then I think

Apr 28, 2009 | Lands Phones

1 Answer

I do not have manual for jabra bt160 how do i connect to phone

Wear it how you like it 4
The Jabra BT160 is ready to wear on your right ear. If you prefer the left, gently flip and
rotate the earhook 180°. (See fig. 2 )
For optimal performance,wear the Jabra BT160 and your mobile phone on the same side
of your body or within line of sight.In general,you will get better performance when
there are no obstructions between your headset and your mobile phone.(See fig.5 )
Answer a call
Tap the answer/eend button on your headset to answer a call
End a call
Tap the answer/eend button to end an active call
Reject a call (DDependent on your phone supporting this feature)
Press the answer/eend button when the phone rings to reject an incoming call.
Depending on your phone settings, the person who called you will either be
forwarded to your voice mail or hear a busy signal
Make a call
• When you make a call from your mobile phone, the call will (ssubject to phone
settings) automatically transfer to your headset
Activate voice dialing (DDependent on your phone supporting this feature)
Tap the answer/eend button. For best results, record the voice-dialing tag through
your headset. Please consult your phone ’ s user manual for more information about
using this feature
Redial last number (DDependent on your phone supporting this feature)
Press the answer/eend button
Adjust sound and volume
Press the volume up or down (+or – ) to adjust the volume (See fig. 1 )
How to...5
Before you use your Jabra BT160, you need to pair it with your mobile phone.
1. Put the headset in pairing 2 mode
Make sure that the headset is on.
Press the answer/eend button and press the volume up (+) button at the same time,
until a solid blue light comes on.
2. Set your Bluetooth phone to ‘ discover ’ the Jabra BT160
Follow your phone ’ s instruction guide. This usually involves going to a ‘ setup,’
‘ connect ’ or ‘B luetooth ’ menu on your phone and selecting the option to ‘ discover ’
or ‘ add ’ a Bluetooth device.** (See example from a typical mobile phone in fig. 4 )
Pair it with your phone 3
Turn on your headset 2
Press the answer/eend button to turn on your headset
Press and hold the answer/eend button to turn off your headset
Charge your headset
Make sure that your Jabra BT160 headset is fully charged before you start using it. Use
the AC adaptor to charge from a power socket. Connect your headset as shown in fig. 3.
When the LED is solid blue, your headset is charging. When the solid blue LED turns off,
it is fully charged.
The Jabra BT160 is easy to operate. The answer/eend button on the headset performs
different functions depending on how long you press it.
Instruction:Duration of press:
Tap Press briefly
Press Approx: 1 second
Press and hold Approx: 5 seconds
Getting started
3. Your phone will find the Jabra BT160
Your phone then asks if you want to pair with it. Accept by pressing ‘ Yes ’ or ‘ OK ’ on
the phone and confirm with the passkey or PIN 3 = 0000 (44 zeros).
Your phone will confirm when pairing is complete. In case of unsuccessful pairing,
repeat steps 1 to 3.

It is all in there


Jul 18, 2008 | Lands Phones

1 Answer

I got a plantronics discovery 610 and i try to connect it to my phone but it just says found no devices

Place the headset in pairing mode so your phone will find it.

Once the headset is in "Pairing" mode you will then need to follow the instructions in your cell phone or Bluetooth device's user guide on how to go it to your phone and search for the headset & pair it to a Bluetooth headset.

To place the 320 Explorer in "pairing mode"

Begin with the headset turned off. Press and hold down the silver call control button in for 6-10 seconds. The light will flash blue first. Continue to hold the button down then release the button when the indicator light starts flashing red then blue.

Note - the passcode or pin is 0000 by default

Jul 04, 2008 | Lands Phones

4 Answers

How to pair a Motorola D200 to a phone??

You will never be able to pair the d200 to a phone or another device, for this is a a2dp bluetooth dongle, that´s why it works with your headphones.

Mar 07, 2008 | Motorola Lands Phones

Not finding what you are looking for?
Lands Phones Logo

Related Topics:

3,488 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lands Phones Experts


Level 3 Expert

98694 Answers

Cindy Wells

Level 3 Expert

4800 Answers


Level 3 Expert

63291 Answers

Are you a Lands Phone Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides