Question about Audio Players & Recorders

2 Answers

Several radio stations have been entered several times. also, I have moved and can no longer receive some of the stations in the memory. How do I get stations out of the memory?

Posted by on

  • masonp Feb 07, 2010

    P MASON - TRY - TECHNICS - TUNER/SOUND PROCESSOR - ST-CH505

  • masonp Feb 07, 2010

    NOT SURE IF THE LAST GO TO YOU. RECEIVER IS TECHNICS - TUNER/SOUND PROCESSOR - ST-CH505

    P MASON

×

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 11,896 Answers

You can unplug the stereo, leave unplugged for an hours or more, then to clear the memory, you will need to press and hold the power button for a full 5 long seconds, then wait half hour before plugging it back in.
Or just make a new preset where the old one is that you want to get rid of.

Posted on Feb 08, 2010

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 11,800 Answers

It would help if you would tell us the brand and model of your receiver.

Posted on Feb 07, 2010

  • Azrael SRL Feb 08, 2010

    The easiest way is to perform a new automatic scan - this way all older programmed stations will be wiped and only the ones you can receive now will be stored. To know how to do that look in the manual. If you don't have it you can get it from here

    https://support.panasonic.co.nz/docstore...

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i set stations on my car stereo?


The procedure is similar on most radios with digital tuning. Select a station you want to enter into the memory by either automatic or manual tune and then press and hold whichever memory button you wish to use for that station.

After a delay of several seconds the display will usually momentarily disappear and when it returns the station will be stored.

Sep 04, 2015 | Audio Players & Recorders

1 Answer

I have and older unit a pioneer VSX 3800, how do you program the radio channels, is there a manuel for these unit i can get sent to myself


Hi.

You have a digital display pioneer receiver and you would like to know how to store radio stations.
  • first tune your radio to your selected radio station
  • next see if the receiver has a button marked memory, and it should have buttons marked 1 2 3 4 5 6 etc
  • After you have tuned in to your selected radio station, if it has a button marked memory,
  • Press the memory button, then press and hold 1 for a few seconds and that should store your selected radio station to preset 1
  • Next, tune in to another radio station and store it by pressing memory then 2 and that should store it in location 2.

  • If your Receiver doesn't have a button labelled memory, and simply has the store 1-6 etc buttons then ,
  • Tune in to your radio station , then press and hold 1 for a few seconds, it will probably flash a few times until its stored in that location 1

  • Next, tune in to another radio station, then press and hold 2 and that should store it in location 2.
  • repeat.

I hope this helps you.
If so please leave a vote or comment.

Have a great day
MobileJB

Jul 18, 2011 | Pioneer Audio Players & Recorders

1 Answer

How do i program the radio


Click below for the manual.

manual

1 Select the radio band and tune in a desired radio

station you wish to store in the preset memory.

2 Press (PRESET).

The Preset screen is displayed.

3 Rotate the Double Action encoder to select the

preset number.

4 Press and hold /ENTER for at least 2 seconds.

The selected station is stored.

The display shows the band, preset number and station

frequency memorized.

A total of 18 stations can be stored in the preset memory (6 stations

for each band; FM1, FM2 and AM).

If you store a station in a preset memory which already has a station,

the current station will be cleared and replaced with the new station.

Press in the outer ring and rotate the Double Action encoder to the

left or right on the Preset screen, you can switch the Preset screen of

another band.

FM-1 FM-2 AM FM-1
You can also change the desired radio band by pressing BAND.


Hope this helps.

Zeppelinx12

Feb 25, 2011 | Alpine iDAX305 MP3USB Car Radio Car CD...

1 Answer

Brookstone SLCDv2.0 The device clearly has a Memory capability since there is a "Set" button and the display shows "Memory" when the button is pressed at a particular FM station. ...


Hi, The receiver does have an in built memory to store upto 6 channels.Please follow the steps below to set up the radio memory:- Up to six favorite radio stations (3 AM and 3 FM) may be stored in memory. the following are steps to set radio memory: 1. Press tUnInG/bAnD to select the band. 2. turn tUnInG/bAnD to locate the desired station. 3. Press the M button. the "M" indicator flashes on the LCD Display. 4. Press 1, 2 or 3 to store the selected station. 5. Press the M button again to confirm. 6. repeat steps 1-5 to set other memory stations.
Incase you would require any information do refer the below web site where you could find picture representation of the same. http://www.brookstone.com/linkedassetservlet?assetId=71937&languageId=EN
Thank you for your time and best wishes for your effort.

Jan 11, 2011 | Audio Players & Recorders

1 Answer

Theres no memory to the clock and radio settings


Hi and thank you for using fixya:

IF your clock is not staying on time make and your stations are going out of memory check your car battery the terminals might be loose making your radio to reset itself every time the batteries moves.
Good luck
thanks

Jun 21, 2010 | Durabrand WD810

1 Answer

XM radio tunes to random station when turned on


There is an internal battery to hold the station and presets. It is probably no good. Either that or there is something very wrong with the unit.

Here is what I recommend. Call XM. Tell them your receiver is not longer functioning correctly and that you are thinking about canceling your service because you don't have a receiver. They will then offer you a receiver because they don't make much money on them, the make their money on the service.

that's how you get a new free satilite radio.

Dec 24, 2009 | XM Radio (XMP6000)

1 Answer

I'm trying to find a manual for it. Actually I'm just trying to figure out how to preset a station on the tuner.(Not sure why this page comes up when i search for a manual for it since there is no logical...


Manual presetting
1.
Tune in the desired station with auto or manual tuning.
2. Press the (MEMORY/) ENTER button.
3. Select the desired preset number (1~30) and press the
(MEMORY/)ENTER button.
• "MEM" is flickering for several seconds.
When using the NUMERIC buttons on the remote control.
Examples) For “3” :
For “15” :
For “30” :
• The station has now been stored in the memory.
• When using the NUMERIC buttons, the station is stored
automatically without pressing the (MEMORY/)ENTER
button.
• A stored frequency is erased from the memory by
storing another frequency in its place.
• If "MEM" goes off, start again from the above step 2.
4. Repeat the above steps 1 to 3 to memorize other stations.

Dec 05, 2009 | Sherwood RD-7500 Receiver

2 Answers

Stored radio stations and time erase when car is turned off


The radio was installed incorrectlly. Make sure the red wire from the radio is connected to a switched 12 volt source(has voltage when car is on, none when it's off) The yellow wire to a constant 12 volt(hot at all times) this wire mantains the radio memory and must always have power.

Nov 21, 2008 | JVC KD-G220 CD Player

2 Answers

Shortwave programmes


Before you call a doctor or an exorcist, verify that you're using your shortwave receiver under normal condition. There are several factors which affects reception of whortwave programs and signals.

1. Check for the time and frequencies. Depending on your country and location, all Shortwave time zones are based on World Time in UTC or GMT ("Universal Time Coordinates" or Greenwich Mean Time") In my country (Philippines, Asia) for example, we are 8 hours advanced from World Time. You can check your time zones and regions using a world map.

2. Check for propagation and band conditions/ openings. During daytime higher frequencies such as 9 -21 Mhz are active, while nightime frequencies are the lower bands such as 3 - 9 Mhz. Daytime and nigthime divider frequency is about 10 Mhz, that means you might receive signals under most conditions during daytime and night time. Check some technical books on amateur radio operations or magazines for radio reception. It might be worthwile to study books or materials on receiving international broadcasts stations before you can receive good or adequate shortwave signals. This might become your hobby too, "DXing" or receiving distant stations from across the world. Try it, but it might be an addicting hobby once you're drawn to it!

3. Check if any shortwave station broadcast in any specific time of day at any frequency. Shortwave broadcasts are scheduled based on band openings mentioned above. If for example I'm a Shortwave broadcaster from Asia, and would like to broadcast my signal through the Americas, I would use band openings with respect with time zones. If it is night time in the Philippines, and daytime in the Canada, I would use the higher frequencies to propagate my signal. So I would specify the time for example "8:00 pm Philippine local time, 12 hours UTC, and 7 am in Canada"--- Asia: 8 hours advanced to UTC, Canada--- 5 hours behind to UTC). So shortwave broadcast schedules varies. Broadcast schedules are available on the net, just search for the Shortwave station you want to hear such as Radio, Japan, Radio Australia, BBC, DW (Deutche Welle) Radio in Germany, China Radio International... There's too many shortwave stations waiting to be discovered out there! Check some books and magazines too such as Popular Communications, Monitoring Times, Passport to World Band Radios, World Radio and TV Handbook, etc. You may want to check if any station would be broadcasting in your dialects as most of these mainstream and regular broadcasters are multilingual.

2. Check your location. If you are using your radio indoors, shortwave signals might not entering your homes or offices due concrete walls and metal railings or fence. There are many factors which blocks radio waves especially in the HF or lowetr bands. Try receiving AM (Mediumwave) first. If it cannot receive any AM station, then you would not receive any Shortwave signal at all, even if you extend fully the telescopic whip. If you cannot receive AM or Shortwave signal indoors, try using your receiver outdoors.

2. Check for local interference. Your receiver might be receiving interference from noise generating gadgets such as PC monitors, TV sets, faulty wall adapters or switching power supplies, motor operated appliances such as washing machines or vacuum cleaners, flourescent lamps, etc. Try turning off or unplugging each of these mentioned gadgets to see if they are the cause. Faulty house wiring or powerline noise might also cause some interference noise which could drown shortwave signals, verify this with your local electrical technicians.

3. Check your radio's settings. Depending on the radio that you use, there might be settings such as attenuator or RF gain, be sure that attenuator are set to zero or turned to off, and RF gain to high. Attenuator must be turned to minimum or OFF position, unless you are receiving too much signas from nearby radio stations. Setting attenuator to mid or high position will attenuate most weak signal, and only those strong local stations will pass through. Setting too much attenuation will prevent you from receiving any station at all. Same with RF Gain, always set it to highest gain setting unless you are receiving too much signals which might overloads your shortwave radio.

4. If these troubleshooting efforts above doesn't works and you still cannot receive any station, then your radio's front end parts might had burn out due to signal overloads. Burn parts might include one or several transistors or diodes. Let your local service technicians check your radio and solve the problem for you. If your radio is still under warranty, send it back to the store or dealer, and let a qualified technician do the repair.


MANNY DE GUZMAN JR.
SoundMagik Home Studio
Site Creator, Teen Models 2007

Visit my website at http://mannydeguzmanartist.wetpaint.com/

My YouTube Channel, http://www.youtube.com/user/mannydeguzmanjartist

My imeem social media channel, http://mannydeguzmanartist.imeem.com/

My Talents and Modeling site at http://teenmodels2007.wetpaint.com/

I've also signed up an account at Total Popstar, uploading some promotional videos. You can watch and rate my videos (you can find my videos on the right side of the screen), just click the link here: http://www.totalpopstar.com/?profile/index/&1740


Thank you very much. I hope I'll really be of help here at FIXYA.COM!!!

Jan 26, 2008 | Sony ICF-SW30 Radio

3 Answers

Tuning the radio


You have two "hot" wires going to the radio. One is the main B+ power and the other is for the "mem" function which keeps clock time and radio station presets in memory. Make sure that you have 12 volts to the memory wire (blown fuse?) If you do then you may have a problem that requires a trip to your local repair guy. Do you loose your preset stations when you turn off your car and leave the face in place (wait several minutes before turning car ignition back on)? If that is so, then you most likley don't have B+ to your memory wire. Good luck.

Aug 16, 2007 | Sony CDX-L480X CD Player

Not finding what you are looking for?
Audio Players & Recorders Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audio Players & Recorders Experts

kakima

Level 3 Expert

102366 Answers

 Grubhead
Grubhead

Level 3 Expert

5126 Answers

The Knight
The Knight

Level 3 Expert

74243 Answers

Are you an Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...