Question about Televison & Video

1 Answer

RUNCO VX-2c Error code 102 fan runs no light

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 11,896 Answers

Either the bulb and lamp hours are used up or the ballast that provides power to the bulb is bad.
You can try resetting the lamp hours:
This all probably comes a couple years too late, but when you install a new lamp, you’ll want to reset the hours on the counter your television has. Doing this will allow you to avoid getting any messages about the lamp needing to be replaced despite you having a new lamp inside your set.
If you need to get into the service menu, you can do so by following these directions:
With power on, hold down VOL minus button on projection display and hold down the PIP or SPLIT button (try both) on the remote simultaneously for more than 5 seconds.

Posted on Feb 07, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The lamp does not attempt to turn on anymore on my Runco VX-1C projector. Power to the projector is good but lamp does not turn on.


I was about to chime in that you should reset the lamp hours after inserting the new bulb ... until I read that you couldn't see the menu because the bulb still doesn't turn on. Hmmm...

Have you checked all of the filters to ensure they're free of dust build-up? I'm wondering if it overheated which caused the fault.

Due to the fact that this model is out-of-production your options have become limited. I recommend at this point you give them a call:

Tech Support at 800-23-RUNCO

Jan 02, 2015 | Runco Reflection VX-1c Multimedia...

1 Answer

RunCo VX1000c RS-232 communication codes


Hi Kevin,

The manual for the RuCo VX1000c is available at http://www.aboutprojectors.com/pdf/runco-vx-1000ci-manual.pdf
The RS232 codes and protocols are towards the back of the manual. According to the manual, the PFP connects to the projector using a CAT5 cable.

HTH.

Jan 02, 2013 | Office Equipment & Supplies

1 Answer

How do I replace the bulb hours in my Runco Media VX-4000d Projector? I already replaced the bulb. Thank you for your help!


Please contact Runco support at 1-800-23-RUNCO. We can assist you.

Sal Di Giacomo
Runco International
WW Service Manager
sal.digiacomo@runco.com

Aug 05, 2011 | Runco VX-5000ci Multimedia Projector

2 Answers

Xerox 3535 error code 102 372


have a xerox 3535 with one blinking light and error code 102 372 on start up any ideas ?

Oct 15, 2009 | Xerox DocuColor 3535 Copier

1 Answer

Reset lamp timer runco vx-5000


There is a service reset "button" located on the input panel on the bottom of the projector. This should be what you are looking for you can also download the manual at this link.
http://www.runco.com/legacy_prods/legacy_manuals/VX-5000ci-DHD_6-07-04_v2.pdf
If you need further assistance please let me know. Also please take a moment to accept and rate my solution accordingly.
Thank you,
Lee

May 07, 2009 | Runco VX-5000ci Multimedia Projector

1 Answer

Windows XP Error: category 102 event id 1003


look like a system crash.
try to go into save mode and do a scandisk
if not, remove any newly install hardware or software.
restart the laptop.

Nov 10, 2008 | Microsoft Windows XP Professional

1 Answer

Reset lamp timer runco vx-5000


Using the remote control for your projector, turn the unit on, then select 'menu' on the remote. On the menu that pops up in the screen, select 'SERVICE', then 'DISPLAY DEVICE', then 'INSTALLATION'... once you select that, scroll over to the "RESET" under the lamp hours... this should reset it.

Here is a link to the owners manual for your unit.

http://runco.com/legacy_prods/legacy_manuals/VX4000d_5000d_manual-v3-1.pdf

Nov 01, 2008 | Runco VX-5000ci Multimedia Projector

1 Answer

Service menu passcode for runco vx-1000d


Hello,

I understand you have a VX-1000d.

You only want to reset if the projector doesn't turn on because it is a safety feature so the lamp does not explode. They get really hot and need to be replaced when due. You can buy one from the supplier or online.
There is a reset button on the inside of the
RGB connection bay(look deep) for a reset button, hold it down until the lamp light turns blue.
If flipped over on it's back, you would see it straight down beyond the connectors. Of course this will reset to factory settings.

Do you have the processor?

Normal 0 MicrosoftInternetExplorer4

Aug 21, 2008 | Runco Reflection VX-1c Multimedia...

3 Answers

Runco Service Passcodes


I have the passcodes for most of Runco products let me know

Dec 23, 2007 | Runco Reflection VX-1c Multimedia...

Not finding what you are looking for?
Televison & Video Logo

Related Topics:

194 people viewed this question

Ask a Question

Usually answered in minutes!

Top Televison & Video Experts

The Knight
The Knight

Level 3 Expert

74459 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

Are you a Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...