Question about Yamaha RX-V1900 Receiver

1 Answer

How do I link mt remote (rx-v1900)with my tv

I have a yamaha RX-V1900 receiver and im not sure how to control my Samsung Tv with the receivers remote

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 30 Answers

OK. So did it come with instructions? If not, it is a rip-off. I suggest you contact your retailer in that case.

-K.R.

"I know what I know because I know what to do!"

Posted on Feb 07, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I Have an Yamaha RX-V1300. Is there anything I can to allow it to pass thru 3D video signal?


No. You'll have to connect the video to your TV and then pass the audio to the receiver. 3-D pass-thru was only added to some audio receivers with HDMI outputs in about 2010. The Yamaha RX-V1300 was released at least 7 years earlier. Video monitors/TVs with 3D display were virtually unknown when this model was released. You can find the specifications for this receiver here: http://usa.yamaha.com/products/audio-visual/hifi-components/stereo-receivers/rx-v1300_black__u/ (click on the Specs tab).

I wish that I had better news for you.

Cindy Wells

Dec 01, 2014 | Yamaha RX-V1900 Receiver

1 Answer

Does the yamaha RX-V1900 have analog zone two output


Yes your amplifier has assignable multi zone capability .You have to go into the initial setup of the amplifier and select if you want to assign any one of the amplifiers ( eg: rear back amp ) as zone 2.

May 22, 2011 | Yamaha RX-V1900 Receiver

1 Answer

How much is a FM/AM tuner replacement part for a yamaha RX-V1900. My connection are broken on current unit.


If you mean the where the aerial goes in, it will be much cheaper to replace that, then buy any board, even if they are still made.
Have a look in Maplins (uk) or Radio Shack (USA) to see if you spot something like it. It will just need soldering on!

Jun 14, 2010 | Yamaha RX-V1900 Receiver

1 Answer

Rx-v1900 hdmi hdtv problem


On most modern receivers you must select which signal type you want it to process.

for example on my Denon, I have to go into the on screen menu and select the input I want ie: video 1.Then tell it which signal I want it to use ie: s-video, component or HDMI input for video and then which input corresponds to the audio signal for that component ie: analog, digital, optical or hdmi.

Its complicated and a pain in the ****

Hopefully that helps call Yamaha they will usually walk you through the process while on the phone.

Feb 14, 2010 | Yamaha RX-V1900 Receiver

1 Answer

HDMI out jack physically broken on my rx-v1900. Fixable?


An audio repair shop should be able to get a replacement connector and swap it for you. I doubt that the part is available from Yamaha (and it would be pricy if it was). The connector shouldbe available generically. Digikey or Mouser should be a good source.

Dan

Nov 18, 2009 | Yamaha RX-V1900 Receiver

1 Answer

Yamaha Rx-v365 trying to program remote for


Press and hold "DTV" then, while holding doen DTV, press power and hold for three seconds. Release both buttons and enter your code. The front panel of the receiver will say "remote setup ok" or "NG" (no good) That being said; while you are in the process of finger acrobatics! make sure your remote is pointing in the general direction of the receiver. Yes, it's a pain, however, once your done, the Yamaha remote is a champ! Hope this helps.

Oct 01, 2009 | Yamaha Rx-v365 A/V Home Theater Receiver

1 Answer

Hi where can i downlowd a manual for the rx-v1900


I would start at the www.yamaha.com web site's support page. Find a Support page, and then look for Downloads. Be prepared to enter specific info about your device, like model number, serial number, etc.
If that fails, enter something like: yamaha rx-v1900 user manual in Google and you should see many different references to it. Spend a few minutes browsing the most likely places by reading the headings.
Good luck!

Aug 21, 2009 | Yamaha RX-V1900 Receiver

3 Answers

Need yamaha codes to program into uverse tv ir remote


(I have the RX-V659). Because the Yamaha remote has TWO SEPARATE buttons - power ON and power OFF (standby). This problem can't be fixed. There's a code to choose power ON and another code for power OFF. But one button can't be two buttons. Bad engineering\ design by Yamaha in my opinion

Jan 09, 2009 | Yamaha RX-V800 Receiver

Not finding what you are looking for?
Yamaha RX-V1900 Receiver Logo

Related Topics:

88 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Audio Players & Recorders Experts

 Grubhead
Grubhead

Level 3 Expert

5158 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

The Knight
The Knight

Level 3 Expert

74383 Answers

Are you a Yamaha Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...