Question about Bushnell Trail Sentry 11-9200 Digital Camera

2 Answers

Bushnell Trail Sentry camrera will not accept any code

I have a Bushnell Trail Sentry digital camera as a Christmas present. I am not able to set the code, I had trouble getting it to even take the default code the 1st time, then finally it did. One time I tried to enter a 4373 code but switched it back, afraid I would forget it. I turned camera off after 154 pictures, removed SD card and then tried to restart camera per directions. It will not take 0000 code or 4373 code. It goes to "erro" after each round of entry and then goes to off. I am lost for what to do. I did have trouble the initial time with it. After multiple tries the 1st time it finally went thru which made me think there may have been an issue with the camera. What can I do? Any ideas?

Posted by on

  • not applicable
    not applicable Oct 30, 2013

    maybe take it back to shop or better to send to manufacture they will fix it i guess for a small cost ..DO NOT just dump it on ebay or trash item why not give the manufacturer a change to be good responsible company and fix or replace item for a small fee

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 12 Answers

Maybe take it back to shop or better to send to manufacture they will fix it i guess for a small cost ..DO NOT just dump it on ebay or trash item why not give the manufacturer a change to be good responsible company and fix or replace item for a small fee

Posted on Oct 30, 2013

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Contributor
  • 43 Answers

If the Bushnell Trail Sentry 11-9200 is turned on without an SD Card in place, it may need to be reset. Reset it by pulling one of the batteries out partway, insert a new or empty SD card, and put the battery back in place. Read this Set Up Guide for instruction how to set up your passcode.

The camera will not Make sure the power is off before installing or removing the SD Card. If you forget, you need to do the reset procedure above.

Buy Name Brand Trail Scouting Cameras here.

Posted on Aug 19, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Is there a factory reset


Normally you have to send it in to Bushnell and have them do it for a fee but in the past I used the following to reset a similar Bushnell trail cam and it may work for you:

1. Turn camera on and wait for the password screen.

2. Press and hold the enter button until the camera switches to the 5 digit password mode. "Trail Sentry cams will not indicate a 5 digit mode on the screen, but it will show "-----".

3.Press enter to confirm 5 digit mode.

4. Enter the 5 digit code "66214, then press enter. *Note it will accept a 5th digit.*

5.Camera should display "PASS" and go into the operating mode.
From here you can program a new password from the setup mode.

Nov 08, 2014 | Bushnell Trail Sentry 11-9200 Digital...

1 Answer

How to format a trail camera


I'm sure the Bushnell Trail Sentry User Manual can help you with this. See -Setup and Operation Guide - If the Sentry is turned on without a card in place, it may not turn off. Reset it by pulling one of the batteries out partway, insert a new or empty SD Card and put the battery back in place. Only remove or insert cards with power off.

Click on this link for more information or to buy additional Bushnell Trail Scouting Camreras

Aug 16, 2010 | Bushnell Trail Sentry 11-9200 Digital...

1 Answer

My pass word on my trail camera shows error I was trying to set the date with the default password... May have screwed up the password in the process How do I reset the camera??


To reset the password:

Turn unit on and wait for password prompt
Depress the and hold the enter button until camera switches into 5-digit password mode _ _ _ _ _.

Trail sentry systems will not indicate 5-digit mode on the screen, but will indicate _ _ _ _ instead of HHHH .

Press enter to confirm 5 digit mode

Enter 5-digit code 66214 and press enter button( trail sentry cameras will accept a 5th Digit after the 4th digit is entered in the _ _ _ _ screen.

Camera will now go into operating mode, and user can now program a new password from the setup mode.

Follow this link to see the user manual PDF:

http://www.bushnell.com/manuals/trail-scout/119000TrailSentry_manual.pdf

Jan 29, 2010 | Bushnell 11-9000 Digital Camera

2 Answers

Lost my password


To reset the password:


Turn unit on and wait for password prompt
Depress the and hold the enter button until camera


switches into 5-digit password mode _ _ _ _ _.
Trail sentry systems will not indicate 5-digit mode on the screen, but will indicate _ _ _ _ instead of HHHH .


Press enter to confirm 5 digit mode


Enter 5-digit code 66214 and press enter button( trail sentry cameras will accept a 5th Digit after the 4th digit is entered in the _ _ _ _ screen.


Camera will now go into operating mode, and user can now program a new password from the setup mode

Nov 09, 2009 | Bushnell Trail Sentry 11-9200 Digital...

1 Answer

My camera is locked and i cant get the password to reset


I'm sure the Bushnell Trail Sentry User Manual can help you with this. See -Setup and Operation Guide - If the Sentry is turned on without a card in place, it may not turn off-reset it by pulling one of the batteries out partway, insert a new or empty SD card, and put the battery back in place. Only remove or insert cards with power off.

Click on this link to buy additional Trail Scouting Camreras

Oct 30, 2009 | Bushnell Trail Sentry 11-9200 Digital...

1 Answer

Bought yesterday. Following instructions,0000 is not the default code on this unit!!


Try this:
Trail Scout and Trail Sentry camera re-programming procedure.
1) Turn unit on and wait for screen to prompt password
2) Press the enter button and hold until camera switches into 5-digit password mode _ _ _ _ _.
Trail sentry cameras will not indicate 5-digit mode on the screen, but will indicate _ _ _ _ instead of HHHH .
3) Press enter to confirm 5 digit mode (for trail scouts go to next procedure).
4) Enter 5-digit code 66214 and press enter button( trail sentry cameras will accept a 5th Digit after the 4th 0ne is entered in the _ _ _ _ screen.
5) Camera will now go into operating mode, and user can now program a new password from the setup mode

Oct 04, 2009 | Bushnell Trail Sentry 11-9200 Digital...

1 Answer

My trail sentry will not let me reset the code


Normal 0 false false false MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman"; mso-ansi-language:#0400; mso-fareast-language:#0400; mso-bidi-language:#0400;} Trail Scout and Trail Sentry camera re-programming procedure.
1) Turn unit on and wait for screen to prompt password
2) Press the enter button and hold until camera switches into 5-digit password mode _ _ _ _ _.
Trail sentry cameras will not indicate 5-digit mode on the screen, but will indicate _ _ _ _ instead of HHHH .
3) Press enter to confirm 5 digit mode (for trail scouts go to next procedure).
4) Enter 5-digit code 66214 and press enter button( trail sentry cameras will accept a 5th Digit after the 4th 0ne is entered in the _ _ _ _ screen.
5) Camera will now go into operating mode, and user can now program a new password from the setup mode

Oct 04, 2009 | Bushnell Trail Sentry 11-9200 Digital...

3 Answers

Bushnell Trail Sentry Camera- forgot password


Trail Scout and Trail Sentry camera re-programming procedure.
1) Turn unit on and wait for screen to prompt password
2) Press the enter button and hold until camera switches into 5-digit password mode _ _ _ _ _.
Trail sentry cameras will not indicate 5-digit mode on the screen, but will indicate _ _ _ _ instead of HHHH .
3) Press enter to confirm 5 digit mode (for trail scouts go to next procedure).
4) Enter 5-digit code 66214 and press enter button( trail sentry cameras will accept a 5th Digit after the 4th 0ne is entered in the _ _ _ _ screen.
5) Camera will now go into operating mode, and user can now program a new password from the setup mode

Oct 01, 2009 | Bushnell Trail Sentry 11-9200 Digital...

1 Answer

Decode to reprogram new pass word


Try this:
Trail Scout and Trail Sentry camera re-programming procedure.
1) Turn unit on and wait for screen to prompt password
2) Press the enter button and hold until camera switches into 5-digit password mode _ _ _ _ _.
Trail sentry cameras will not indicate 5-digit mode on the screen, but will indicate _ _ _ _ instead of HHHH .
3) Press enter to confirm 5 digit mode (for trail scouts go to next procedure).
4) Enter 5-digit code 66214 and press enter button( trail sentry cameras will accept a 5th Digit after the 4th 0ne is entered in the _ _ _ _ screen.
5) Camera will now go into operating mode, and user can now program a new password from the setup mode

Sep 30, 2009 | Bushnell Trail Sentry 11-9200 Digital...

2 Answers

Password reset


If 0000 doesn't work then you have to send it back to Bushnell to reset the password. It should not take long to get it back according to others with the same problem, just to let you know...


Benjamin

Apr 26, 2009 | Bushnell Trail Sentry 11-9200 Digital...

Not finding what you are looking for?
Bushnell Trail Sentry 11-9200 Digital Camera Logo

426 people viewed this question

Ask a Question

Usually answered in minutes!

Top Bushnell Cameras Experts

kakima

Level 3 Expert

102366 Answers

Johnny Massengill
Johnny Massengill

Level 2 Expert

345 Answers

Brad Brown

Level 3 Expert

15441 Answers

Are you a Bushnell Camera Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...