Question about Computers & Internet

Open Question

Drive will ping at IP address 64.136.144.201 and browsing to same address as LED is red results as below: http://64.136.144.201/status/index.asp?status_init=init Forbidden You don't have permission to access /status/index.asp on this server. Additionally, a 403 Forbidden error was encountered while trying to use an ErrorDocument to handle the request. Apache/2.0.54 (Unix) PHP/5.1.2 Server at 64.136.144.201 Port 80 Additional Non correct conditions from Saint Loren after 53 seconds the right Led goes steady red and the Message above is produced in the browser. Drive will allow login and start on web page setup path if accomplished before red light. Drive will not Reset although no clear reset instructions can be found, IP stays at 64.136.144.201 where I had been using it when it was working. Web server can be accessed ant the end of the Green led cycle before it turns red. By rushing this I have got past Lang. Time setups in the drive setup path but the red led stopps all. Drive may contain the Win32/Gael.d virus as denoted by Microsoft Live OneCare. Earl list folders that pertain to this drive are Jan 11 2009 Drive PN; 9GY5A8-500 SN: 2DD403KA Thank you for any help

Posted by on

  • Saint Loren
    Saint Loren Feb 07, 2010

    The device is a Maxtor Central Axis network storage drive.

×

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
IrishDruid
  • 2712 Answers

SOURCE: AXIS CD TOWERS E100

I am sorry, but this is not really my area of expertise. You could try Ekse or Benimur who are good at networking.

You do not have to rate this post, as I did not really provide a solution.

Good luck!

Posted on May 22, 2008

Ad
  • 13433 Answers

SOURCE: AXIS CD TOWER Problems

I'l get back to you, got some stuff to do right now but here are the manuals for your product maybe you can find a solution there untill I get back.

http://www.axis.com/techsup/cdsrv/cd_e100/index.htm

Posted on May 22, 2008

Benimur
  • 6966 Answers

SOURCE: AXIS CD TOWERS

Hi,

I am assuming that you are referring to the tower (desktop) as the server while the laptop is the client. While the client can access the server's CD drive, you can not ping the server. A couple of ideas:
1. verify that both server and client belong to the same Workgroup;
2. verify that both server and client have the same Subnet Mask and that their satic IP adds are near each other;
3. Server's firewall settings/configurations does not allow/prevents ping response; and/or
4. the server might be using Zonelab, McAfee Firewall, Microsoft ICF SP2 or some other form of port blocking.

Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information.

Good luck and kind regards.

Thank you for using FixYa.

Posted on May 23, 2008

  • 115 Answers

SOURCE: Forbidden You don't have permission to access

probleme on website

Posted on Sep 08, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Not recognize dns


Google has many different ip addresses. They have servers I guess you call them everywhere. I downloaded several apps that looked up IP addresses cause the ping had different ones I didn't use. They all led back to GooGle owning that address. Nothing to be alarmed about, theres just no escape from Google, they see everything, track everywhere, and won a lot of different IP

Apr 06, 2017 | TP-LINK Computers & Internet

Tip

How to ping an IP address in Windows Applies to Windows XP, Windows Vista and...


How to ping an IP address in Windows

Applies to Windows XP, Windows Vista and Windows 7

1. Click Start - Run

2. Next enter "CMD" and click OK

571b2d7.png
3. Next at the command prompt type "ping" then press the space bar and then enter the IP address that you would like to ping. After you have the command typed press the Enter key.

Example: ping 192.168.1.1

327db5e.png

4. If the IP address is valid and not blocked by a firewall then you should get a responce that looks like this.


28899e5.png
Note if you get a message like shown below this means that the ether you do not have a valid IP or ICMP Echo requests are being blocked.


86bf3df.png
In most cases it is being blocked by the device that you are trying to ping. However it can be block in the Windows firewall or other software firewalls. The links below will help you verify that you have ICMP Echo enabled on your computer.

How to allow ping (ICMP Echo) request through Windows 7 Firewall

How to allow ping request through Norton Internet Security 2010 Smart Firewall

on Sep 21, 2010 | Computers & Internet

2 Answers

My router will not connect the power light keeps blinking


Check this tip out from Linksys. It is for a G VPN Router but you could use the same steps to troubleshoot. Title: Resolving Blinking Power or Diag LED on a Linksys Wireless-G VPN Router Article ID: 4982 If the Power LED on your Linksys router is blinking, this means the device is not ready. It should go off once the router completes its diagnostic test. If the Power LED won?t go off, it indicates that there?s a possible hardware problem with the router. To resolve this, you will need to perform five steps: Resetting the Router Assigning Static IP to the Computer Pinging the Router Accessing the Router?s Web-based Setup Page Updating the Router?s Firmware For instructions on how to reset the router, follow the steps below. Resetting the Router Hold in the RESET button at the back of the router for 30 seconds. Unplug the power to the router then plug it back in. If after resetting the router and the Power LED is still blinking, try resetting the router again for another 30 seconds. Then proceed with assigning a static IP address on the PC. For instructions, follow the steps below. Assigning a Static IP Address on Your Computer Most of the time, if the power LED on the router is blinking it loses its ability to assign IP addresses to the PCs connected to it, which is why you need to assign the computer a static IP address. After assigning a static IP address on the computer, check if the computer is still communicating to the router by performing a ping test. To ping the router, follow the steps below. Pinging the Router Ping test helps trace the communication between the computer and the router. The computer sends packets to the router and in return the router sends out replies to validate the connection. In this example, our router IP address is 192.168.1.1. NOTE: If you?re using Windows 98 or ME, click here. Windows 2000/XP Step 1: Click Start, then Run. Step 2: When the Run window opens, type ?cmd? in the Open field, then click OK. Step 3: When the MS DOS Prompt appears, type ?ping 192.168.1.1? and press [Enter]. Step 4: Check the ping statistics. You should get Packets: Sent =4, Received =4, Lost = 0 (0% loss). NOTE: If you?re not getting good replies from the router, it means the router is not communicating properly with the computer anymore. You can already consider the device defective. Windows 98/ME Step 1: Click Start, then Run. A window similar to Step 2 will appear. Step 2: When the Run window appears, type ?command? in the Open field, then click OK. Step 3: When the MS DOS Prompt appears, type ?ping 192.168.1.1? and press [Enter]. Step 4: Check the ping statistics. You should get Packets: Sent =4, Received =4, Lost = 0 (0% loss). NOTE: If you?re not getting good replies from the router, it means the router is not communicating properly with the computer anymore. You can already consider the device defective. If you get good responses from the router, access the router?s web-based setup page to see if a firmware update is possible. For instructions, follow the steps below. Accessing the Router?s Web-based Setup Page In order to perform a firmware update, you should be able to access the router?s web-based setup page. Updating the firmware is one way of resolving the blinking power light on the Linksys router. To access the router?s web-based setup page, click here. NOTE: If you?re having difficulties accessing the router?s web-based setup page, the router is considered defective. If you?re able to access the router?s web-based setup page, proceed in updating the firmware upgrade.

Jul 21, 2010 | Linksys Wireless-G Broadband Router

1 Answer

Cannot browse webgui page


do you have an address in the same IP network as the router? can you PING to the router IP address?  If you're not sure, find your IP address and ping your default gateway, it should be the WAG200G.

Mar 26, 2010 | Linksys WAG200G Router

1 Answer

Can connect to 2wire, but can't browse


What is the ip address you got from the 2wire router. ??

Try release and renew for new ip. Clear the cache and temporary internet files, and then try pinging the router's gateway ip and check . If pinging. then ping any website's ip address. if successful then try going online. Else you need to power off and power on your router and then try again.

Sep 06, 2009 | 2wire (1000-400108-001) Router

1 Answer

Ping www.yahoo.com - FAILED


try to check the ip address before accessing the internet.
if you not getting a valid ip address then try to reset you d link router.

Apr 13, 2009 | D-Link AirPlus DWL-G630 802.11g/b Wireless...

1 Answer

Freecom external network drive 500gm I installed today via wireless router and connection main pc and laptop and copied files over. Now does not work and will not see the external drive. Operating...


If it is a network drive. I believe it must have an IP address.

The best way to start troubleshotting is to know the ip address

Then you can ping the Ip address to know if your computer can see the drive.

If the ping time out...then the drive is not on the network.

If the ping reply then it is on the network. so you'll need to look at the share.

Rgds,

Mar 21, 2008 | Computers & Internet

1 Answer

Cannot connect second computer to my networn


I have listed several things here that you can use to find the problem. Sorry this is so long...network problems can be very tedious to find.

First check your version of Windows:
Double click on "My Computer", then click on "View System Information" to make sure you have at least Service Pack 1...or better yet....Service Pack 2.

Next check your Windows XP network settings:
Click on Start....Control Panel....Network Connections...Local Area Connection...Properties(button). Scroll down the list to find Internet Protocol(TCP/IP) and click on it to highlight it. Now click the properties button below the list. You should now be able to click the small buttons to select both of the "Obtain....automatically" choices for IP address and DNS server. Click on "OK" to close each of the windows.

Now you can test your computer to see if it is "talking" to the router: Click on Start...Run...and type "cmd" in the small box and click "OK". This will open a black command window where you tell the computer what to do. Type the command "ipconfig" and press return (enter). This will list your ip address, subnet mask, and default gateway. Make a note of the default gateway address so you can use it for the next test. If the IP address begins with 192.168...then your computer is probably communicating with the router okay. If your IP address is blank or starts with 169...then your network connection to the router may NOT be working.

The final test!!! Use the default gateway address from the last step to do a "ping" test. In the black command window...type "ping" followed by the default gateway address. For example: IF the default gateway happens to be 192.168.1.1....then type the ping command this way: ping 192.168.1.1

If the result is a list of replies from the gateway address...great!! Your network connection is working. If the ping command results in a list of "request timed out", or something else, then your network connection needs more help.

The ultimate test is to try using the Internet with your browser.
If this works, next try typing your gateway address into the brower address bar. It should connect you to the router setup page.(?)

Let me know the results of each of these tests, and I'll be happy to assist you further, if needed.

Jan 12, 2008 | Computers & Internet

3 Answers

How to test Connections with Ping


Ping is one of the first tools to use to check computer, router and Internet connectivity. It's run at a command prompt, but getting the basic information is quite easy. You can do the whole thing in 30 seconds. 1. To run ping, type Start > Run. 2. Type cmd in the Run window, and click OK. A black and white command line window pops up. 3. Type ping followed by an IP address or a DNS address. 4. Press Enter to execute the command. Three useful examples: 1. ping 127.0.0.1 (This is a "loopback ping" ? your computer trying to talk to itself. This tests whether your computer is able to handle Ethernet traffic. If this has a negative result, the computer has an operating system problem.) 2. ping 192.168.1.1 (If the result is "Request timed out", type ping 192.168.0.1. If that also times out, then the computer is not making a connection to your router.) 3. ping www.netgear.com. (Tests whether your computer can contact Internet computers.) When there is no problem, the ping results look as shown in the following screenshot. Three items of interest in the results are highlighted with arrows. The first arrow shows the computer being contacted is replying. (The DNS address "www.netgear.com" is converted by ping into the equivalent IP address, 10.1.1.86.) This shows both that your network is connnected to the Internet, and that that computer on the Internet is running normally. www.netgear.com is always running, so this is a good test address to use. The second arrow shows that Ethernet packets have "0% loss". This is the best possible result. It means that the network connection is lightly loaded, and that it has not been necessary to transmit any of the same information twice. The third arrow shows the average time it took to answer. "Average = 0ms" is the best possible result. Probably you'll only get responses this quickly from computers on your own network. Interpreting Ping when There's a Problem As far as NETGEAR equipment, the problem you're most likely to run into is "Request Timed Out". This means there is no connection. Read these posts: http://www.fixya.com/ThreadView.aspx?prdid=252225&thid=102077 and http://www.fixya.com/ThreadView.aspx?prdid=252225&thid=102074 Another error is "Unknown host", which just means that the DNS or IP address you typed doesn't exist. Probably, you made a typo. Other problems are generally outside the scope of NETGEAR support. Often they are problems with your ISP ? contact them with concerns. A controversial situation is when packet loss is not 0%. Sometimes this indicates a severe problem, but in other situations it doesn't indicate any problem whatever. However anything higher than 5% is definitely a problem. If the average round trip time is > 500 ms, there' s possible latency problem. Again, contact your ISP. Limitations of the Ping Tool * Ping is not a good tool for diagnosing intermittent problems. * Good results are reliable, but ?bad results? could be caused by any number of things, and are not necessarily reliable! * Ping uses ICMP, which has low priority, showing speeds that are slower than regular network traffic. Some computers reject ICMP, and therefore pinging, entirely. * When an IP appears between the source and destination in a traceroute command it does *not* mean that that IP must be pingable.

Feb 19, 2006 | NetGear CG814M Wireless Cable Modem...

Not finding what you are looking for?
Computers & Internet Logo

Related Topics:

258 people viewed this question

Ask a Question

Usually answered in minutes!

Top Computers & Internet Experts

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

kakima

Level 3 Expert

102366 Answers

David Payne
David Payne

Level 3 Expert

14161 Answers

Are you a Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...