Question about Clock Radios

Open Question

Redgroove docking station modle no ds-376

I have a problem with my redgroove docking station modle no ds-376,i cant set volume for the alarm,the factory setting is too loud.

Posted by on

  • 3rigel Nov 02, 2008

    When you switch on to audio it automatically comes on at volume 24 which is too loud, can you configure it to come at a lower level?

×

6 Suggested Answers

  • 30 Answers

SOURCE: Alarm Volume

THE ALARM BEEP IS SET TO ONE VOLUME MODE ONLY THE RADIO VOLUME IS THE ONLY ONE YOU CAN CONTROL UNLESS YOU HAVE A HIGH AND LOW SWITCH THEN JUST SWITCH TO LOW.

Posted on Jun 30, 2007

SOURCE: How do I reset the radio alarm preset on Timex (T307S) Clock Radio

if the radio alarm is still showing the nonexistent 98.5, you would need to reset the radio alarm. Press and hold button 1 (top left hand side) until the display starts blinking. Then press the preset button for 98.1. It should then display 98.1 on your radio alarm. good luck this is the most difficult set of instructions I've seen yet

Posted on Oct 02, 2007

informatica
  • 1113 Answers

SOURCE: I cant set the music station for my t622h alarm clock

Hi - You can download the manual by clicking the link underlined in blue below:

t622h700d750.jpg

Please take a moment to rate this solution & let us know if the information given was useful to you - Good Luck!

Informatica

Posted on Sep 10, 2008

  • 70 Answers

SOURCE: Z213B Clock Radio

d3b32db.jpg 281dcb6.jpg Good luck.

Posted on Dec 20, 2008

  • 814 Answers

SOURCE: alarms

[http://www.emersonradio.com/owners/iPod%20Series/iC200_NCab050307.pdf] Copy this web link and paste it into the address bar of your browser. It will take you to the Emerson customer support web page of a pdf copy of the owners manual for your Clock/Radio. You can use the print function to make a pdf copy of the manual for your own use. To increase the sound of the buzzer in the alarm you will need to exchange the internal battery for a new battery. The buzzer works on this battery power alone. The model of the battery (CR2430) and how to replace it are in the owners manual on pages 41-44. If this fix doe not solve the problem you are having with the weak buzzer. You can call the Emerson customer support at this telephone number 1-800-898-9020. Between the hours of 9am-5pm CT. Give them the make and model number of your Clock/Radio and ask them for assistance with your problem. I hope this information helps you with the problem of the weak buzzer sound on the alarm of your Clock/Radio.

Posted on Jun 13, 2009

  • 1 Answer

SOURCE: how to switch auto alarm on and off

There is no alarm, but it states on the box that there is ! I took mine back and got a refund

Posted on Dec 27, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does my radio alarm only work with one station?


When you're setting the alarm you should be able to choose any of the stations programmed into your radio. Just press radio to choose radio for the wakeup, and press one of the presets. You can also set the volume at which it comes on.

Jul 13, 2014 | Bose Wave Radio

2 Answers

I don't know how to set the clock for a MA4203 model


I couldn't find the information for your particular model, but I did figure out the general procedure for Memorex alarm clocks currently in production:

  1. Make sure power is turned off (no radio or whatever playing). Press the Time Set button (on some models, this is the Skip Search Back button for an iPod docked in the unit).
  2. When the display blinks (on one model, the volume control knob lights up), press the Hour button (Vol. -) to set the hour, then press the Minutes button (Vol. +) to set the minutes. On the model with the light-up volume control, rotate the volume control knob to set the time.
  3. When you have the time set, either wait 15 seconds or press the Time Set button again to start the clock.
Setting the alarm works the same way on single alarm models, but the Alarm Set button may be the Skip Search Forward button. Dual alarm models have separate Alarm A and Alarm B buttons.

Feb 05, 2011 | Memorex Clock Radios

1 Answer

Wake up with the radio is always set to level 19... I would like to set my radio alarm with a lower volume... my centrios is a Speed to Sound CENTRIOS IPOD/IPHONE CLOCK RADIO I will return this


We also have this problem. Found this info in the product's Q&A on the website: http://answers.thesource.ca/answers/9026/product/1218694/centrios-centrios-ipod-iphone-clock-radio-white-questions-answers/questions.htm

"Ok. there is a way that you can LOWER the wakeup radio volume. turn on the radio (forget about the alarm right now) and go to the station that you want. when you get to the station, you should be able to press the 'skip/fast forward' button on the remote. when you do this, number 5 should show up beside the station #. When you do this, it lowers the overall volume of every volume level, so now level 19 is equal to volume level 9/10, which for me is loud enough to wake me, but not give me a heart attack! so, now when the alarm goes of, the volume is a lot lower. BUT if you want to wake up to your ipod, this method will NOT work, it will still be up at level 19. so when you turn on your ipod, it will be really LOUD. again, this only works with the radio."

Also if you are waking to ipod and not radio this was in the reviews:
"Fooled with it for a bit and discovered that you have to turn down the volume of the iPod first before putting it on the dock. We've tried it a few times just to make sure and it worked every time!!"

Still not a perfect solution, but a great improvement. Hope this helps someone.

Jan 08, 2011 | Centrios Classic Flip Clock

4 Answers

How to switch auto alarm on and off just how to set alarm and disable and enable product is a sainsburys red dab clock radio not the one with docking station


Dont know how to set the time for the alarm, but to switch it off press and hold the menu button until it asks if you want to reset the radio and then follow the instructions. It means you have to reset radio every time but at least it stops pesky alarm going off...

Nov 15, 2009 | Clock Radios

1 Answer

How do I change the radio station on the radio alarm


Here is the full manual
http://www.timexaudio.com/pdf/T311IB57574_35.pdf

Here are the instructions from the manual.

Setting the Radio Alarm
1. Press and hold the
Radio Alarm Button. The display will flash and the Radio Alarm Indicator will
appear. If you do not begin setting the time within ten seconds of pressing the button, the display will stop
flashing and you will need to press the
Radio Alarm Button again.
2. While the display flashes, press the Reverse and  Forward Buttons to set the wake time. Hold a button
for a few seconds to set the time rapidly. Be sure to set the correct AM/PM time, as shown by the PM Indicator.
3. After setting the radio alarm time, you will need to select the station. First, press the  Radio Band Button
to select a radio frequency. Next, select a station using the Memory Set 1-6 Buttons. For more
information on programming radio stations into memory, see the Programming Radio Station Settings section
of this manual. Rotate the  Volume Thumbwheel to set the wake sound volume.
4. After setting the radio alarm wake time and sound, you will need to select the 7-5-2 setting. The 7-5-2 setting
lets you set the alarm for a full week, weekdays only, or the weekend. Before setting the alarm, be sure that
the correct date is set, as shown in the “Auto-Set” and Manual Time and Date Settings section of the manual.
While the display is still flashing, press the  Date/7-5-2 Button until the desired setting is shown.
5. After you have set the radio alarm wake time, sound, and 7-5-2 setting, press the  Enter Button. The
Radio Alarm Indicator will appear on the display, showing that the radio alarm has been set.

Aug 08, 2009 | Timex T311T Clock Radio

1 Answer

Lost manual for a timex t307s


Setting the Alarm 1 for AM/FM Radio
1. Press and hold the 2 Radio Alarm 1 Button. The display will flash and the Radio Alarm Indicator will appear. If
you do not begin setting the time within ten seconds of pressing the button, the display will stop flashing and you will
need to press the 2 Radio Alarm 1 Button again.
2. While the display flashes, press the 1 Reverse and 6 Forward Buttons to set the wake time. Hold a button for a few
seconds to set the time rapidly. Be sure to set the correct AM/PM time, as shown by the PM Indicator.
3. After setting the radio alarm time, while the display is still flashing you will need to select the station. First, press the
L Mode/DST Button to select a radio frequency. Next, select a station using the M Memory Set 1-6 Buttons. For
more information on programming radio stations into memory, see the Programming Radio Station Settings section of
this manual. Rotate the O Volume Thumbwheel to set the wake sound volume.
4. After setting the radio alarm wake time and sound, you will need to select the 7-5-2 setting. The 7-5-2 setting lets you
set the alarm for a full week, weekdays only, or the weekend. Before setting the alarm, be sure that the correct date
is set, as shown in the “Auto-Set” and Manual Time and Date Settings section of the manual. While the display is still
flashing, press the 9 Date/7-5-2 Button until the desired setting is shown.
5. After you have set the radio alarm wake time, sound, and 7-5-2 setting, press the 4 Enter Button. The Radio Alarm
Indicator
will appear on the display, showing that the radio alarm has been set.
Setting Alarm 2 for Nature Sounds/Buzzer
1. Press and hold the 7 Nature Sounds/Buzzer Alarm 2 Button until the Alarm 2 settings and Sounds Alarm
Indicator appear on the display.
2. Press the 1 Reverse or 6 Forward Button to set the Alarm 2 time.
3. Use the L Mode/DST Button to select a nature sound or the buzzer to wake to. There is a choice of five sounds:
Sound #1: Ocean Surf
Sound #2: Birds
Sound #3: Brook
Sound #4: Wind Chimes
buz: Buzzer
4. See Note #4 in the Setting Alarm 1 section for instructions on setting the 7-5-2 alarm setting for Alarm 2.
5. After you have programmed the Alarm 2 settings, press the 4 Enter Button or wait ten seconds to return to the clock
display. The Sounds Alarm Indicator will appear on the display, showing that the alarm is set.

Nov 18, 2008 | Timex (T307S) Clock Radio

1 Answer

I cant set the music station for my t622h alarm clock


Hi - You can download the manual by clicking the link underlined in blue below:

t622h700d750.jpg

Please take a moment to rate this solution & let us know if the information given was useful to you - Good Luck!

Informatica

Sep 10, 2008 | Timex Auto-set Clock Radio

2 Answers

IPod circuit board


SDI Technologies Inc. has part just got tto there page and ask them for ipod dock connector part (part # IH5-101)

Feb 24, 2008 | Clock Radios

1 Answer

How to set alarm and ring with radio?


Hi gidgid.
This is direct from manual mailed to me from Oregon Scientific re my own contrast problem.
1. Press [ALARM] to switch to display the alarm setting.
2. Select ALARM 1 or ALARM 2 using [ALARM].
3. Press and hold [ALARM] for two seconds.
4. Use VOLUME [ + ] / [ - ] to enter the hours.
5. Press [ALARM].
6. Use VOLUME [ + ] / [ - ] to enter the minutes.
7. Press [ALARM].
8. Use VOLUME [ + ] / [ - ] to select ALARM or RADIO. If
ALARM is selected, a two-minute crescendo alarm will be
emitted at the set time when the alarm is active. If RADIO is
chosen, the radio will be turned on for two hours at the set time
instead.
9. If RADIO is chosen, use [STATION] to choose the radio
station and press [AM / FM] to select AM or FM.
10. Press [ALARM].
11.Use VOLUME [ + ] / [ - ] to set the volume of the wake up radio.
12. Press [ALARM] to exit.
Note: If there is no battery for the radio, there is no operation for
step 9 ~ 11.
sleepy head

Jan 13, 2008 | Oregon Scientific RRM112 Clock Radio

1 Answer

How do I reset the radio alarm preset on Timex (T307S) Clock Radio


if the radio alarm is still showing the nonexistent 98.5, you would need to reset the radio alarm. Press and hold button 1 (top left hand side) until the display starts blinking. Then press the preset button for 98.1. It should then display 98.1 on your radio alarm. good luck this is the most difficult set of instructions I've seen yet

Sep 11, 2007 | Timex (T307S) Clock Radio

Not finding what you are looking for?
Clock Radios Logo

Related Topics:

415 people viewed this question

Ask a Question

Usually answered in minutes!

Top Clock Radios Experts

The Knight
The Knight

Level 3 Expert

68368 Answers

Gyula Lacz

Level 3 Expert

482 Answers

Cindy Wells

Level 3 Expert

4761 Answers

Are you a Clock Radio Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...