Question about TitanNet TITANTANKLESS. COM PRESENTS THE TITAN SCR2 WHOLE HOUSE TANKLESS WATER HEATE

1 Answer

When turn on the hot water only the top red and green lights are on and the water is not hot

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,030 Answers

Is it wired correctly..check all your wiring
if its a new install call the place of purchase or the manufacturer

Posted on Feb 06, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rheem rte13 standby (green) light not on


You might have crossover problem caused by bad faucet cartridge.
http://waterheatertimer.org/Crossover.html

The green standby light should come on when 240Volt power is applied. Page 6 manual.
Both red lights should come on when tankless is activated. Page 6 manual

RTE 13 requires 60 amp breaker and 6 gauge wire
http://waterheatertimer.org/How-to-wire-Tankless-electric-water-heater.html
http://waterheatertimer.org/pdf/Rheem-TanklessElectricUC_AP15447.pdf

Factory temperature setting is usually default 120 degrees.
Adjust temps page 11 manual
Thermostat calibration is always approximate.
120 degrees is not hot enough to burn the skin.
Exceptionally cold incoming water temperature can cause tankless not to heat enough hot water: install tempering tank to preheat water to room temperature.
Tankless cannot be exposed to more than 11 grains hardness in water. Delime tankless yearly, clean water filter monthly, do not install low-flow restrictions or conserve water since the flow rate must remain high for tankless to activate.
Rheem does not post service manuals for their tankless water heaters.
Call Rheem 800 432-8373

Aug 05, 2012 | Rheem Tankless Hot Water Heater...

1 Answer

Pilot light on hot water heater is out


you need to shut off the the red nob and turn the nob off in front take the cover off remove the heat shield turn the nob on top to pilot use a piece of paper to light put in next to pilot and hold button down for 20 to 50 secs pilot should stay lit turn nob on front then burner should kick on then you should be all good

Mar 21, 2012 | Water Heaters

1 Answer

I have two wires going to my hot water heater red and black but no ground but the inspector says i need to connet a ground line toi the green screw on the electrical pannel on the top of the hot water...


It is the same as all the other appliances in your house, they should be earthed (grounded). You can run a new earth wire from the meterbox to the hot water heater or pick up an earth anywhere in the house and run it to the heater. The earthing conductor connecting to the hot water heater should be the same size as the active and neutral conductors or no less than 2.5mm square.

Feb 14, 2011 | General Electric Water Heaters

2 Answers

No hot water, control board light stays green


It may be bad thermostat terminals of the water heater, or, alternatively, the very top heating element is in need of replacement. See this handy diagnostic article for more info:
http://yourhandymanzone.com/Your_Handyman_Zone_How_To_Pages_Home_Improvement_Zone_Heating_Systems_Water_Heaters_Cold_Water_Still_Released_Despite_Water_Heater.htm

Hope this helps.
Brad

May 11, 2009 | Water Heaters

1 Answer

Energy smart system light flashing one time


If you still have a warranty, call the manufacturer and they will send you a new brain for FREE, You just half to pay the shipping. I just replaced one on my Mother-in-laws. They stated that there were problems with the brains. It is very simple to replace.Just make sure you have the breaker turned off.

Dec 09, 2008 | Water Heaters

Not finding what you are looking for?
TitanNet TITANTANKLESS. COM PRESENTS THE TITAN SCR2 WHOLE HOUSE TANKLESS WATER HEATE Logo

296 people viewed this question

Ask a Question

Usually answered in minutes!

Top TitanNet Water Heaters Experts

Donni Steen

Level 3 Expert

659 Answers

Brad Brown

Level 3 Expert

15557 Answers

Gil Shultz

Level 3 Expert

3368 Answers

Are you a TitanNet Water Heater Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...