Question about Frigidaire Washing Machines

1 Answer

Machine will run through entire cycle and will not spin. It quits at the spin cycle. I checked the Black boot at the bottom. Removed and cleared out coins. Checked pump- it was turning freely. Reinstalled boot. Error message 43 which indicates control board problem. I ordered control board part# 13700500 Installed- same error message. Unit will not spin. Will operate through all cycle and stops at spin. Ran diagnostic test. Turned program knob 8 clicks from start to position 8- Delicate. The drain pump and door lock solenoid will activate and the washer will operate in high spin and drain. Error code 43 repeats.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I had a similar problem and found out the "latch" on the washer door broke off. The machine won't run in spin cycle if the door is"open", but it would run through the wash cycle.

Posted on Feb 05, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My top load Bravos washing machine wobbles during spin cycle.


Most likely suspension rods and bushings need replacing. Also check outer tub ring. Sometimes it will break from beating on sides of washer, behind where water comes out.

Sep 30, 2017 | Maytag Bravos MTW6600T Top Load Washer

3 Answers

Fwt449gfs2 washes, empties some water, does not spin, knob does not advance


i would check the timmer. run it through a cycle and when it stops slightly move the timmer ahead. if that works than you need to replace the timmer... i had a washer that did that and it turned out to be the timmer on mine.

Aug 06, 2008 | Frigidaire ATF6000ES Front Load Washer

2 Answers

Washer wont spin. It went thru the whole wash cycle, but now it won't spin, and there is no error code. It comes on and the time counts down, but it doesn't spin.


Hello,Hi, If it doesnt spin, check to see if the motor is running, then proceed as follows:
  • If the motor is running, your washer probably has a frozen pump pulley or a broken pump belt. To check the pulley, remove the pump from the washer and try to rotate the pulley manually. If it doesn't turn freely--if it's frozen or stiff--replace it. If the pump belt is broken or looks quite worn, replace it--but be sure to check the pump pulley before you change the belt.
  • If the motor isn't running, the lid switch may be defective. If so, the washing machine can't spin and may not function at all. The switch is inside the washing machine main housing near the door frame. Often you have to raise or open the top or front of the washing machine to get to the switch. If it's defective, you need to replace it.
Thanks

Jun 02, 2010 | Frigidaire ATF6000ES Front Load Washer

1 Answer

Violent spin cycle on the Frigidare front-loading washer


I assume you bought it new, so on that basis, did you remove the transit packing materials inside the machine ?

Front loading washing machine normal design is for the drum assembly to be supported by two or more springs at the top, and two dampers at the bottom. This allows the drum to move in a controlled fashion and also minimises vibration, particularly during spinning.
When the machines are shipped from the factory, transit packaging is put inside the machine to ensure that any shocks to the machine during transit dont damage the springs or dampers. This must be removed before use otherwise you get pretty much the symptoms you describe.

The manual that cam with it will show you how to remove the transit packaging. In such a short time I suspect you wont have suffered any damage, but take the transit packaging out as soon as possible.

Nov 04, 2009 | Frigidaire ATF6000ES Front Load Washer

1 Answer

Bosch WFF1800 - not spinning


HI,

move the kicking plate on the front-bottom of the machine. You will see o circular lid there, turn it on anti-clockvise to open. All of the water blocked will come from there, be careful. Look carefully that there are some objects blocking the water draining. Then turn on the machine on draining programme, the plastic rotor should turn fastly when the machine is on. If it is not running, change the pump motor. If it is running, but machine is not draining again you can understand that there is an objeck stuck on the hose between drum and pump motor. Lay down the machine on its rear facade, you will see a large and black hose between drum and pump motor. When you remove it, you will see that there is something that blocks water running.

thank you for using fixya,rate my answer,
vijay

Oct 04, 2009 | Bosch Exxcel WFO 2465 Front Load Washer

1 Answer

Green slime in coffee machine


Try running a couple cycles through of full strength vinegar. If that doesn't do it run a weak bleach solution (6 to 1 / water to bleach) through it. Repeat vinegar every week then once a month if it clears.

May 07, 2009 | KitchenAid Artisan

1 Answer

Washing machine did not complete rinse/spin cycle.


We had the same problem, the pump was clogged. First UNPLUG THE WASHER! Tilt the washer back slightly and there are two screws that hold the bottom front panel on. Remove them and pull down on the panel to remove it. To the right you will see the pump. Mine has a large black collector boot coming from the tub. There are three clamps connecting the lines to the boot and on large ring clamp connecting it to the tub assembly. Remove as much of the standing water from the tub as you can. We were able to get ours to drain after a couple of cycles. We also raised ours up on blocks to put a basin under it. It helps to have a shop vac ready incase you have a lot of water. Once you remove the clamps take the black boot out. There is a plastic strainer in the boot. I found a sock, wires and $1.26 in change in mine. Look under and check the pump impeller. Check the drain line to your house sewer standpipe (I sucked it out with the shop vac). I replaced two of the compression clamps with regular radiator clamps, to make the next time easier. Clean and dry the underside, before using. Run a load to check for leaks before replacing the front panel.

Mar 09, 2009 | Frigidaire ATF6000ES Front Load Washer

1 Answer

Frigidaire Gallery Model FWT449GFS1


There is an obstruction in the drain pump. The only way to clear the obstruction is to remove the lower panel at the front by removing the 2 screws at the lower edge. This will allow the front panel to drop down. You will need to unplug the machine for the next part.

Now this will get a little messy... Be sure to have a lot of towels nearby to sop up the water. On the lower right hand side there is a pump with a black bellows attached which is also attached to the bottom of the tub. This black hose is clamped to the front of the pump if you unclamp the hose the remaining water in the system will spill out. You will have to reach inside the bellows and remove whatever obstruction is inside. some models will have a trap inside which may have to be removed from the top of the hose assembly by unscrewing the clamp on the bottom of the tub.

The hose will have to be reattached in the reverse manner. It can be quite tricky to do so... Once the machine is back together you can run a rinse and spin cycle, it should go into the full spin when all the water drains.

This procedure may have to be repeated a couple of times to completely remove all of the carpet fibres.

Aug 07, 2008 | Frigidaire GLTF2940E Gallery 3.5 Cu. Ft....

1 Answer

Model 665 16874


removed and disassembled inlet water valve - minature basket filter was clogged with white particulate which felt gritty.  cleaned and reassembled and reinstalled.  Works fine now.  Idiot repairman never mentioned a filter but wanted to replace entire valve at cost of 140 dollars including service call.   sears sux bigtime. And, from my experience with Fixya, so does your service since I never heard a thing since July EXCEPT for an offer to upgrade.  Thanks for nothing.

Jul 11, 2008 | Kenmore 16602 / 16604 / 16609 Built-in...

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

246 people viewed this question

Ask a Question

Usually answered in minutes!

Top Frigidaire Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1466 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Are you a Frigidaire Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...