Question about Canon FAX-L350 Plain Paper Laser

1 Answer

Memory Sending When trying to send multiple pages the fax is only scanning and sending one page at a time, it will not hold the 80 pages I'm trying to send in memory. The % of memory full is zero. The document feed lever is set to automatic. Hope you can help. Thanks Jenny

Posted by on

  • octecinc Nov 16, 2008

    Precisely the same error here - RAM problems perhaps?

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 8 Answers

~When sending one page, does the display indicate usage of any memory ? If it does then it is merely a feeder problem. If you open up the front flap (the whole panel holding all the number keys and display it hinges forward) you will see to the rear of the machine two rubber rollers - the rubber 'goes off' after a bit - it either dries out/ perishes or gets dirty. You can try cleaning these with a slightly damp rag (avoid paper towels/ fluffy cloths). However, if they have gone past their use by date you may have to consider replacing your machine (unless a proficient engineer can replace them for less than the cost of a new machine). Whilst the front flap is open, below the lower of the two rubber rollers is a glazed screen which houses the scanner. Run you finger across the glazed area and see just how much dirt is being scanned across each of your pages being sent - you might be surprised!

In the meantime, this is not an unusual situation - but do you really have to send 80 pages of fax (5 - 20 I can understand)? The risk of missing one page (and it being a crucial one is too great). However, my L350 will not pickup following pages and is much happier sending single pages only. The only solution, I am afraid, is for you to stand over the fax and feed one page in after another, just as the previous one leaves the input tray. You can keep an eye on how many pages have actually scanned and if it matches up with how many you have fed through by keeping an eye on the page count on the machine's display.
Can't offer a better solution i am afraid. hope this helps tho.

Posted on Jan 12, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Using a brother MFC-J415W printer, what are the steps in sending a fax?


How to fax :
1. Entering fax mode To enter fax mode press (Fax), and the key will glow green.
2. Sending a fax from the ADF (Automatic Document Feeder): Using the ADF to send your faxes is the easiest way. To cancel a fax in progress press Stop/Exit.
a. Make sure you are in Fax mode . b. Place your document face up in the ADF. c. Dial the fax number. d. Press Start.
The machine scans the pages into memory and then sends the document.
3. Sending a fax from the scanner glass : You can use the scanner glass to fax the pages of a book, or a single page at a time. The documents can be up to Letter or A4 size. Press Stop/Exit to cancel a fax in progress.
a. Make sure you are in Fax mode . b. Place your document face down on the scanner glass. c. Dial the fax number. d. Press Start.The machine starts scanning the first page.
For more detailed instructions, you can go directly to Section 4 - page 22 of the manual in Brother's site. Hope this helps.

Apr 14, 2011 | Office Equipment & Supplies

1 Answer

When we start to send a fax the machine shows "memory" in the window and the fax will not go through. If we continue to try, after 3-4 times the fax will finally go through. Any idea what we can do to stop...


If this is a newer style machine...most units scan the pages into memory before they send it. What are you trying to send???? is it a complex color brochure..????
Try sending a simple page of type and see if the machine does the same thing. This may be a limitation of the memory capacity of your machine.

Apr 07, 2010 | Office Equipment & Supplies

1 Answer

Insstructions for sending a Fax on a Brother


You can find the entire user manual by clicking here:
http://www.brother-usa.com/ModelDocuments/Consumer/Users%20Manual/UM_MFC_240C_EN_249.PDF

Or, here are the instructions for sending a fax:

Entering Fax mode 5

To enter fax mode, press (Fax), and
the key will glow green.

The LCD will show the new job number and
the memory available.The number of pages
you can scan into the memory will vary
depending on the data that is printed on them.

Faxing from the ADF 5
a Make sure you are in Fax mode .
b Put the document face down in the ADF.
c Dial the fax number using the dial pad.
d Press Black Start or Color Start.
The machine starts scanning the
document.

Note
• To cancel, press Stop/Exit.
• If the memory is full, the fax will be sent in
real time.

Faxing from the scanner glass5
You can use the scanner glass to fax pages
of a book one at a time. The documents can
be up to letter or A4 size.

You cannot send multiple pages for color
faxes.



Make sure you are in Fax mode .

Load your document on the scanner
glass.

Dial the fax number.

Press Black Start or Color Start.
If you press Black Start, the
machine starts scanning the first
page. Go to step e.

If you press Color Start, the
machine starts sending the
document.

Do one of the following:
To send a single page, press 2 to
choose No. (or press Black Start
again).
To send more than one page, press
1 to choose Yes and go to step f.

Put the next page on the scanner glass.

Press OK.
starts scanning the page.

.

Dec 15, 2009 | Brother MFC 240C All-In-One InkJet Printer

1 Answer

I wanna send a fax


Hi there,
Sending Faxes.
* Flow of Sending Faxes.
The operation flow of sending faxes is as follows.
Step 1:
Load the original to send on the Platen Glass or the ADF.
Step 2 :
Adjust the fax quality and scan contrast.
Step 3 :
Dial the receipent' s number.
Step 4 :
Send Faxes
- Using the Platen Glass
1) Press the Color or Black button.
If you have two or more pages of the original, load the next page on the Platen Glass and press the Color or Black button
2) After scanning all the pages of the original, press the OK button to send the fax.
- Using ADF
1) Press the Color or Black button.
The fax is sent automatically.

* Before sending Faxes
- Adjusting the Scan Contrast or the Image Quality (Fax Resolution)
** Adjusting the Scan Contrast
Contrast is the degree of difference between light and dark. Increasing the scan contrast setting further blackens dark areas and whitens bright areas, whereas decreasing the contrast setting reduces the difference between bright and dark areas. You can adjust the contrast among the 3 contrast levels.
1) Press the FAX button, then press the FAX Quality button.
2) Press right or left arrow ot select the contrast.
Pressing the left arrow button decreases the contrast, and pressing the right arrow button increases the contrast.
3) Press the OK button.

** Adjusting the Image Quality (Fax Resolution)
You can adjust the image quality (fax resolution) of the document you send. The higher you set the image quality setting, the better the output quality will be at the other end, but the longer it will take for the transmission. Adjust the image quality according to the type of document you are sending.
1) PRess the FAX button, then press the FAX Quality button two times.
2) Press the right and left arrow keys to select the resolution.
FAX RESOLUTION - STANDARD
Standard : Suitable for text-only documents.
FINE : Suitable for fine-print documents.
PHOTO : Suitable for photographs.
3) Press the OK button.

*Sending Faxes - There are 4 methods for sending functions
a) Memory sending
b) Manual sending
c) Dialing the coded speed dial
d) Redial

a) Memory sending
1) Prepare for faxing
a) Turn on the machine,
b) Load the original on the Platen Glass or the ADF.
Note : You cannot scan double-sided documents from the ADF.
c) Press the FAX bitton.
d) Adjust fax settings as necessary.
2) Start faxing.
a) Dial the receipient's number using the Numeric buttons or coded speed dialing.
b) Press the Color button for color sending, or the Black button for black and white sending. I
c) When the following message is displayed, lad the next page on the PLaten Glass.
Scan Next -> Start
Transmit-> OK
If only one document go to step f).
d) Press the same button as you pressed in step b).
e) Repeat step c) and d) to scan in all pages of the document.
f) Press the OK button.

Manual Sending
1) Connect a telephone to the machine.
2) Prepare for faxing.
a) Turn on the machine.
b) Load the original in the ADF,
c) Press the FAX button.
d) Adjust the fax settings as necessary.
3) Lift the handset of the telephone connected to the machine.
4) Dial the receipient's number on the telephone.
5) Talk through the handset to the recipient.
If you hear a high-pitched signal instead of the recipient's voice, go to step g),
6) Ask the recipient to set recipient's fax machine to receive faxes.
7) When you hear a high-pitched signal, press the Color button for sending color sending, or the Black button for black & white sending. Then hang up the handset.

Dialling The Coded Speed Dial
1) Prepare for faxing.
2) Press the Coded Dial button.
3) Press the Numeric buttons to enter the two-digit code (00-19) assigned to the number you want to dial.
4) Press the Color button for color sending, or the Black button for black & white sending.

Hope this helps. Please rate my response.
Thanks
Have a good day.





Nov 27, 2009 | Canon PIXMA MX310 All-In-One Printer

1 Answer

Sending fax


If you sending the fax over the memory, fax can scann doc. while dialing, or in the same time, but if you sending directly (on-hook dial) fax is sending the document while beeing reeded.

You may try to check the phone lines, browse the documents before sending,clean the original document feed rollers,...
if fax sudenly stops and wrinkle the orig. documents there is problem in scanner area

Jan 16, 2009 | Canon FAX-JX200

1 Answer

I need to know how to send a Broadcast fax to multiple numbers


This is right from the manual:
You can use the Multiple Send feature, which allows you to send a fax to
multiple locations. Originals are automatically stored in memory and sent
to a remote station. After transmission, the originals are automatically
erased from memory.
1 Press Fax.
2 Load originals face up into the ADF, or place a single original face
down on the scanner glass.
For details about loading an original, see page 5.1.
3 Adjust the document resolution and darkness to suit your fax needs.
See page 9.1.
4 Press Menu until Fax Feature appears on the bottom line of the
display and press OK.
5 Press the Scroll buttons until Multi Send appears and press OK.
6 Enter the number of the first receiving fax machine and press OK.
You can use speed buttons, speed dial numbers, or group dial
numbers. For details, see page 10.2.
7 Enter the second fax number and press OK.
The display asks you to enter another fax number to send the
document.
8 To enter more fax numbers, press OK when Yes appears and
repeat steps 6 and 7. You can add up to 209 destinations.
Note
You cannot use group dial numbers for another fax number.
9 When you have finished entering fax numbers, select No at the
Another No.? prompt and press OK or Start.
The original is scanned into memory before transmission. The
display shows memory capacity and the number of pages being
stored in memory.
10 If an original is placed on the scanner glass, select Yes to add
another pages. Load another original and press OK.
When you have finished, select No at the Another Page? prompt.
The machine begins sending the fax to the numbers you entered in
the order in which you entered them.

Manual - see page 54

Dec 15, 2008 | Samsung SCX-5530FN All-In-One Laser...

2 Answers

Storing Outbound Faxes not sending.


if you print a tx journal does it have an error on those you tried to send

Mar 19, 2008 | Panasonic PanaFax UF-8000 Laser Fax

1 Answer

I want to scan then send instead of scanning whilst sending


There are 2 methods of sending 1. Through memory, in which the machine scans the document then sends when all pages have been scanned. 2. In real time, in which the document is placed in the ready mode and the line monitor or handset is used to dial the number. In this case the document is not scanned until a response is heard from the other machine.
However, in the case of the memory being full, either of documents in the queue or if there are documents waiting to be printed (because of no toner or no paper) then the machine will not allow sending from memory.

Feb 07, 2008 | Canon FAX-L200 Plain Paper Laser

1 Answer

Document to memory before sending


Here's the manual. Look at page 6-8. That tells how to turn on real-time transmission. You just need to do the same thing, except switch it to off when you get to that step. http://www.brother.ca/en/products/pdf/manuals/MFC8220-UG.pdf

Sep 06, 2007 | Brother MFC-8220 Fax

Not finding what you are looking for?
Canon FAX-L350 Plain Paper Laser Logo

76 people viewed this question

Ask a Question

Usually answered in minutes!

Top Canon Office Equipment & Supplies Experts

kakima

Level 3 Expert

102366 Answers

old marine
old marine

Level 3 Expert

2005 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Are you a Canon Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...