Question about Maytag 24 in. MDB5600A Jetclean II Built-in Dishwasher

1 Answer

Water will not go in dishwasher

The dishwasher sounds like it is running, all lights and buttons work. But when I opened it up the soap had not dissolved and no water had been in the dishwasher. Dishes still dirty.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Maytag Master
  • 2,651 Answers

First make sure your water supply had not been shut off under sink.next check the float switch inside the tub., In the front cornerof the dish washer floor (either left or right depending on model)when you open the door. Grab the float and lift slightly up it should move freely up and down, and although pretty faint you should hear a switch "click" as you doit. try it now!!!, if not id focus on bad water valve

Posted on Feb 22, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The soap dispenser opens & the soap tablet (power ball) drops to the bottom but doesn't dissolve


1. Water temp is wrong should be 140-145
2. spray arms clogged with food
3. water valve is not letter the correct amount of water in

after it fill's check to see water amount in bottom , dose it sound like it is starving for water ? it would sound like it was surging

Dec 01, 2011 | Whirlpool GU2400XTP Built-in Dishwasher

1 Answer

The soap holder is opening during the wash cycle but the soap tablet is not dissolving. Any ideas?


Is the water coming on? Is water hot enough? Is washer overloaded, water jets aren't hitting the soap? Maybe try a different brand of soap tablet? Run the dishwasher in "heavy soil" mode which will use hotter water and run for longer?

Nov 20, 2010 | Frigidaire 24 in. FDB1050RE Built-in...

1 Answer

Help! My dishwasher runs thru it's cycles but when I open it I find my second detergent cup still full of soap and my dishes still dirty. I have an older maytag dishwasher but have never had this...


Hi,

There are three common problems that cause the Soap Dispenser or Cup not to open. I have a tip that will explain these problems in detail....

Dishwasher Repair Problem Detergent Cup does not Open

heatman101

Aug 27, 2010 | Dishwashers

2 Answers

Soap won't dissolve in dishwasher


I had the same problem and my wife fived it by unsticking a valve to the left side of machine in front lets water in she poped it open and dried soapm came out restarted and now works fine.

Jul 26, 2009 | Frigidaire 24 in. FDB635RF Built-in...

2 Answers

Water enters dishwasher, soap door opens but soap


That's a normal path for the soap. It sounds like the water just sits in the bottom without being pumped through the spray arms. Does the pump motor run? Pop the door open in the middle of the washing cycle--you should see hot water dripping from everything and the soap picked up and circulated with the water. If this machine has seen a lot of use, the intake screen under the lower spray arm may be plugged and is accessed by removing the spray arm and working your way down to the bottom of the deck. Might be a problem for a service technician to take care of.

Jul 19, 2009 | Jenn-Air 24 in. JDB1080AWS Built-in...

1 Answer

Doesn't cycle to open soap dispenser


RUN THE TEST PROGRAM TO DO THIS YOU WILL HAVE TO USE BOTH HANDS. Press and hold "Scrub Wash" &
"Delicate/Economy" buttons TOGETHER WHILE HOLDING THE 2 BUTTONS IN HIT THE POWER BUTTON RELEASE THE 2 BUTTONS AND HIT THE 2 BUTTONS AGAIN YOU SHOULD GET A 21 0R 23 CODE AND THE TEST PROGRAM WILL RUN IT WILL TAKE 45 MIN TO RUN BIT WHEN DONE IT WILL SHOW A CODE 1 OR 0 MEANS NOTHING BUT IF YOU GET A NY OTHER # OR LETTER IT CORRESPONDS TO A FAULT
2 = Heating fault 8 = NTC (temperature sensor) fault
1 = Aqua Sensor ("Sensotronic") fault 4 = Filling fault F = Filling fault (display occurs during wash, not test)
DON
262-893-4840

May 02, 2009 | Bosch 24 in. SHU66C05 Stainless Steel...

1 Answer

Kitchenaid kudso1dlss3 clean light flashing cannot do a new cycle


I do not have the same model as you, my model is KUD01ILBS6 but I have the same problem. A service tech told me it was a error code and here is how to fix it.

1 open the dishwasher door
2 hit high temp scrub button
3 then hit energy saver dry button
4 do step 2 & 3 again
5 close the door
6 hit the cancel button
7 you can hit cancel button again then try to start your dishwasher

This works for me, you may have to do this every few months because there is a glitch in kitchenaid where if the water temp is not sensed right it will keep the dishwasher from working. It took me 3 service calls to find this out.

Jan 17, 2009 | KitchenAid 24 in. KUDI01FLSS Stainless...

1 Answer

Soap packets don't melt/disolve


sounds as if you amy have a problem with the dispensor door not opening correctly perhaps opening at end of cycle when all water is already released.Ive seen that sometimes the "tabs" or "packets of detegent are too tall and interfere with normal opening of the latch mechanism. manufacture would reccommend using powder instead.

Nov 04, 2008 | Dishwashers

Not finding what you are looking for?
Maytag 24 in. MDB5600A Jetclean II Built-in Dishwasher Logo

137 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Dishwashers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Michael Thomas
Michael Thomas

Level 3 Expert

3051 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Are you a Maytag Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...