Question about Washing Machines

1 Answer

Haie hw-c1460tve I have only had this washer less then a month, i put a wash on and when i went back to it, there was a message on the screen saying err2 I cant find the manual so am clueless aswell as helpless as to what the problem is and whether orm not i can fix it or if i have to call the store i bought it from for someone to come out and fix it. any ideas would be gratefully received

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Err2 means "Drainage error. water not emptied within 4 min.
Correction: Clean the filter and check the drain hose for a blockage. If error still exists, please contact the maintenance personnel." This is what it says in the instruction manual

Posted on Nov 01, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Have an Amana NAH6800, I must unplug it and plug back in to get it to start wash cycle. Also, keybord is locked until a couple of minutes after the wash cycle starts. Called repairman, he said control...


WELL IT IS POSSIBLE THE SECOND CONTROL BOARD WAS BAD ALSO? A 6 YEAR OLD WASHER IS YOUNG U CAN GET A GOOD 10-15 YEARS OUT OF A WELL KEPT WASHER.

Dec 03, 2014 | Amana Washing Machines

1 Answer

Getting nf message


NF means "no flow". Check for proper water pressure from the house. To do so, turn the water on and put the hose inside the washer or a bucket.

If water pressure is good, check the water valve inlet screens. Most residential washing machines have inlet screens. The screens prevent minerals from clogging the solenoid. With the hoses removed, you can visually inspect the water inlet screens. If the water valve screens are clear the inlet valve with the screens itself will need to be replaced. To replace the water valve, remove the top of the washing machine. Three screws hold the top down. The screws that hold the top down are on the back of the top panel. Once removed the top will slide back and off. Now remove the wire harness that connects to the valve. One screw holds the valve to the washers cabinet. Removing the screw and sliding the valve over will release the valve from the back panel enabling you to complete your repair.

One last thing to check is the fill hoses. These front load duet washers call for a lot of water quickly. So if you have stainless steel braided flood-safe hoses, they will trip for no reason at all. Replace these flood safe hoses with more traditional hoses. If the hoses are good and you haven't found anything slowing down the flow of the water, your electronic inlet water valve is just faulty on the back of your washer and will need to be replaced because it's just not allowing water flow into the washer correctly.

May 30, 2012 | Maytag Neptune MAH5500B Front Load Washer

1 Answer

I have a GE Energy Star Front Load Washer, Model #GFWN1100LWW and the error message on the screen is E5.7. After unplugging and plugging the machine back in, the message is still there. I called GE...


Could it be E57? If so, this means that the main control board is bad.
"Never disconnect the power to the washer while it is in the service mode. Doing so may result in a damaged control board."

You may want to check this site for more info:
http://www.appliance-repair-it.com/GE_front_load_washer.html

Hope this helps a bit.. :)

Jun 07, 2011 | Washing Machines

1 Answer

My WM 2455 HW washer won't start washing. It


my washing machine will not turn on. it has power but will not turn on

May 07, 2010 | LG Washing Machines

2 Answers

Electrolux less than 2 years old and the printed circuit boards need replacing - is it possible to go back to electrolux to sort out as under 2 yrs? There is no warrenty on this apart fromthe inital 12...


you could try your luck but my gess is there just going to stick there heads in the sand and say humbug! only two years is not a lot realy is it,,,mine went on for 15 years,, it rusted out first!

Mar 08, 2010 | Electrolux EW1209i Front Load Washer /...

3 Answers

My Haier HW-C1460TVE-U washing m/c keeps giving (CLrF) ERROR Code


Anyway, my machine shows an error code "clrf". I just spoke to someone at Comet, and apparently this means there is too much foam in the machine. The machine will then refill with water and try to rinse it out, but if after that the machine still has too much foam in, then it will stop the cycle. Hence why my clothes are still wet (although I'd not realised they weren't rinsed properly either!).

I have not been using excessive amounts of washing powder, and usually use powder tablets or the liquid tablet sort, so they are a set amount and I don't do anything daft like stick 6 tablets in! I find it ridiculous that this would cause a problem with the washing machine, as I've used them perfectly fine with other washing machines.

Anyway, the advice from Comet was to keep trying different washing powders until i find one that foams less.

Jan 07, 2010 | Haier Washing Machines

1 Answer

Washing machine finished its last wash and is no longer working ?


All HAIER Washing Machines come with a 3 year parts and labour warranty - Ring them and get them to come and repair..

Apr 10, 2009 | Haier Washing Machines

3 Answers

My Haier HW-C1460TVE-U washing machine was installed this morning did the empty cycle first then did a load of towels worked perfectly did another wash Err code Unb came up. Got sprit level and checked...


Have been to one of these machines today. UNB will still show even if the machine is empty. I think the feedback amplifier on the main PCB is at fault. If I have any luck with it I'll post another message

Jun 29, 2008 | Washing Machines

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

315 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...