Question about Hotpoint Aquarius WF000 Front Load Washer

1 Answer

Hotpoit belt i am having trouble fixing on a belt on the back of my hotpoint WF645 washing machine please help i have run out of ideas

Posted by on

  • Anonymous Feb 22, 2008

    hotpoint dryer belts

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Governor:

    An expert whose answer got voted for 20 times.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 10 Answers

Hook the belt around the motor spindle first then get the belt as far round the pully as you can once at that stage hold the belt firmly as you can on the pully and turn the pully round making sure that the belt does not slip off keep turning the puully round till the belt is fully on once on spin the drum around by hand to make sure that it is on the pully square with motor spindle. job done. if this helped please leave feed back.

Posted on Feb 24, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My wt640 hotpoint washing machine wont spin and says f-05


F05 - Pressure switch jammed on full - Check pump for blackages. Also check the drain pipe 2 so that it can drain out. if you have checked for blockages and can not find any reset machine by switching off at plug for 5 mins then back on and try again hope this helps.

Sep 28, 2010 | Hotpoint WF645 Front Load Washer

1 Answer

My Hotpoint WF645 washes ok but is very noisy, especially during the final spin. Any suggestions why this might be?


sounds like it could be a bearing going out, or simply might be something stuck around the drum

Aug 13, 2010 | Hotpoint WF645 Front Load Washer

2 Answers

WF745 Control PCB


Yon can puchase the part you need direct from Hotpoint, go to>

WWW.HOTPOINTSERVICE.CO.UK

In the menu on the left, click on> SPARES.

Then click on the appropiate tab.

Hopefully, you will find the part you are looking for.
Please rate my solution.
Thankyou.


Jan 23, 2010 | Hotpoint WF645 Front Load Washer

2 Answers

Hotpoint WF645 error message: test


press start once then press again then hold on/off and cancel for a few seconds should now turn test off should be ok now

Jul 15, 2009 | Washing Machines

1 Answer

Hotpoint WF645 : Do I Need special tool to clamp


not worked on this model.but hotpoint are usually eaSY. no special tools.but i found it easier to take the front of the machine and work at it that way about 1 hour

Jun 30, 2009 | Hotpoint Aquarius WF000 Front Load Washer

1 Answer

I have a hotpoint aquarius wf645 when i put it on a wash cycle it will fill for 1 minute then drain a message comes up F-o7 please help


hold in the start and cancel buttons for 10 seconds, a "test on" message appears, hold in the start and cancel button again for 10 seconds and "test off" message appears, set your wash to whatever mode and it should work...it did for me!

Apr 26, 2008 | Hotpoint Washing Machines

3 Answers

Softner still in the draw


The detergent/softner dispenser is located above the detergent drawer. A water pipe is connected to it and water entrance and distribution to drawer's cells (following the programmed cycle)are done by a lever's movement (part of the dispenser). The lever movement is controlled by two solenoids that received their power from the timer. By opening upper machine's cover you will have an access to the dispenser. Disconnect the power cable from the machine before moving to next step !!!! Look first that they are not any disconnected wires. Move manually dispenser's lever and see if water running to all cells (depend on your movement). In case it doesn't work properly remove the unit from the machine and try to clean it (I hope it will help, otherwise you should replace the unit). In case it works properly (manually) - you should test with a multi-tester solenoid's resistance. the one that doesn't have a resistance measurement should be replaced. Good luck !!

Aug 03, 2007 | Hotpoint WF645 Front Load Washer

1 Answer

Hotpoint acquiarius WF645


To exit test mode, press start, display goes wild) press start again (display settles down) Then press on/off button and start buttons to gether and hold for a few seconds, machine will now read D;end, or similar, will now work okay

Jul 07, 2007 | Hotpoint WF645 Front Load Washer

Not finding what you are looking for?
Hotpoint Aquarius WF000 Front Load Washer Logo

Related Topics:

134 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hotpoint Washing Machines Experts

hungoverrr

Level 1 Expert

5 Answers

puggy666

Level 1 Expert

47 Answers

gbob59

Level 3 Expert

2963 Answers

Are you a Hotpoint Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...