Question about Endurance T10HRC Light Treadmill

1 Answer

Motor Controller Board Schematic

I have a burnt out mosfet on the motor controller board. Wondering if anyone has a schematic to this treadmill board or a recommended Mosfet size to replace it. There are no part numbers on the mosfte.

Posted by on

  • outfield502
    outfield502 May 11, 2010

    you must first remove the damaged piece, and then note the number that is printed. you succeed in sales of electronic parts. you have some soldering experience, are you sure that only that part was damaged?



1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Endurance Master
  • 832 Answers

If you are the original owner the parts in residential settings is lifetime so call body-solid @ 1-800-556-3113 ext 520

Posted on Mar 02, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I need the mc2100lts-30 232196 board diagram

Hi to all,

Somebody can help, because I have the PFTL39509 Proform 6.0 ZT, but is not working properly because the Motor controller MC2100LT-12 is failing I am not the original owner and I try to fix it but I can not find the schematic for the motor controller. I reviewed the SCR S4025L, The Diode and the mosfet and all of them are ok
also I checked the bridge AC to DC

May 31, 2012 | Exercise & Fitness

1 Answer

When I step on my treadmill it stops

if it not yet been solved your problem, I suggest you the following: you should review the the motor brushes, or check the motor controller board.
the component that could be corrupted on the card is (IRFP250N) is a mosfet

May 15, 2012 | Nordic Track NordicTrack Treadmill, A2550

1 Answer

Free schematic of the motor ccontroller board for the weslo 10.0c model #wltl1007, #wctl1007

Dear Sir:

As you must undestand this will be a issue, Most factory They do not supply for customer any schematic, only for tech personal.

However you can find in some place paying the schematic.
I will give you the website. or going to

www. then go to customer service, give your model, etc talk with them.

If you have the number of transistor, i can help you maybe.

note: this main motor controller board, are manufactured in Taiwan, I have the name of manufacturer.

sincerely.. Merry Christmass

ernesto cuadra
managua, nicaragua. c.a

Dec 17, 2011 | Exercise & Fitness

1 Answer

E5 sportcraft tx400 treadmill


See the schematic how the Main Controller has 90% functions in Treadmills


Nov 24, 2011 | Exercise & Fitness

1 Answer

15A fuse going out. Replaced 3 with no success, spark on low end of board after about 5 seconds, thenn fuse went.. Unplugged power wires to the lower board, powered up treadmill and the fuse survived. ...

You are going to need a motor controller, or find someone who can repair the one you've got there.
If it blows the fuse immediately on power up, it may require a full wave bridge rectifier replaced on the controller. If it blows when the start button is pushed, it might be a MOSFET or SCR found on the motor controller..
Sportsart fitness can be reached by phoning 1-866-709-1750. The website is found at There you can find a dealer/service depot in your area.

Dec 19, 2010 | Sportsart 6300 Treadmill

1 Answer


if the motor controller card is the model MC_60 you should change D4015L diodes and SCR's S4015L but if MC_2100 you should change the MOSFET IRFP250N

Sep 14, 2010 | Proform Crosswalk 500 Treadmill

2 Answers

I have a problem with my MC-2000ES motor control board. The HV BUSS LED is not on and therefore no DC voltage to run the motor.I have checked the diodes and SCR circuit and all look OK. I believe there is...

just change the Diodes D4015L and SCR´s S4015L whit a caugting buy the new change and ready or is a MC-2100 w / transformer just change the MOSFET IRF250N

Aug 31, 2010 | Proform Crosswalk 500 Treadmill

1 Answer

I need schematic for motor controller be. weslo

If I make no mistake the controller has marking for the wire placement. Look closely at the connection, it should give you a color code.

Nov 17, 2009 | Cadence Exercise & Fitness

Not finding what you are looking for?
Endurance T10HRC Light Treadmill Logo

652 people viewed this question

Ask a Question

Usually answered in minutes!

Top Endurance Exercise & Fitness Experts


Level 2 Expert

115 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers


Level 2 Expert

70 Answers

Are you an Endurance Exercise and Fitnes Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides