Question about Hitachi 42V715 42" HDTV

1 Answer

Power light is on, temp light blinks, and lamp light blinks, no picture.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 130 Answers

Its possible that your lamp is bad, or you have not closed the lamp cover properly. If you don't close it, the sensor will tell the TV not to turn on.

Posted on Feb 04, 2010

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 4234 Answers

SOURCE: No sound no picture

The temp light blinking means that the fan is not running. The lamp light blinking means that the lamp door os not secure. Check to be sure that all access doors are closed properly. There are safety interlocks to prevent the set from powering up if all doors are not properly closed. Did you replace the lamp recently? Re-open the access door and be sure that it is closed completely and straight.

Let me know if you have further problems.

Dan

Posted on Jan 14, 2009

  • 336 Answers

SOURCE: picture suddenly went out and the lamp and temp

Hi,If your tv is between 2-4 yrs most likely it's time to replace the lamp.If you hear continuous clicking it could be the ballast which is the board that powers the lamp.If you hear buzzing it could be the color wheel,which is a spinning wheel that creates the color on your tv.God bless you!

Posted on Oct 13, 2009

  • 18 Answers

SOURCE: Hitachi 55VG825 rear proj television blinking light and screen doesn't light up

Refer to owners manual ! Blinking indicates the type of fault that is occuring on all your tv sets. example : power light on red - indicator light beside it green but blinks rapidly for half a second rapidly then shuts off. This refers to a faulty lamp or a lamp that is near its expiration. Read your manuals if indicators refer to easy repair sweet, but if it says call tech then bummer...

Posted on Jan 05, 2008

welcomejee
  • 10594 Answers

SOURCE: Hello, have a Hitachi

Hi,
Replace Lamp in TV, lamp replacement procedure is written in user manual.

Posted on May 16, 2009

Slinteriors
  • 8617 Answers

SOURCE: I own a Samsung HL-R5067W 50

The color wheel needs replacing. Thats causing the whining and it will also make the lamp light blink.

Posted on Sep 20, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hitachie 42v715


The lamp is dead.The lamp in the tv now,been in used 1 1/2 or 2 years?The lamp life span is over.

May 16, 2010 | Hitachi 42V710 42" Rear Projection HDTV

1 Answer

The tv won't come on it gets power but no picture and on the indicator lights on the control panel only the lamp indicator comes on and just blinks. Did the lamp go out?


The manual says if the lamp light is blinking to check the lamp cover. If it is the temp light that is blinging check that the fans are not locked or shorted.

Dec 17, 2009 | Hitachi 50V500 50 in. HD-Ready LCD...

2 Answers

Turn tv on and red light blinks with no picture or power


according to the manual (I'm having the same problem), it depends on whether the TEMP light is blinking, or the LAMP light. There's a good trouble-shooting page in the manual (available from www.panasonic.com/support). Good luck - to me too. :)

Sep 15, 2009 | Panasonic Televison & Video

1 Answer

No picture on a Samsung HL-P4663W, trouble lights confusing...


The most common blink code for the Standby/Temp LED is the Temp Sensor and or Actuator Board. You can confirm which on by jumping the CN106 connector on the Actuator board. If the set works now, the Temp Sensor must be replaced. If it doesn't work, the Actuator Board would need to be replaced. If you are not familiar with the chassis or electronics at all , I do not recommend trying to fix it, call a professional. Don't take the chance of damaging it further.
I hope this helps,
Skyassoc

Jun 29, 2009 | Samsung HLP4663W 46" Rear Projection HDTV

1 Answer

No sound no picture


The temp light blinking means that the fan is not running. The lamp light blinking means that the lamp door os not secure. Check to be sure that all access doors are closed properly. There are safety interlocks to prevent the set from powering up if all doors are not properly closed. Did you replace the lamp recently? Re-open the access door and be sure that it is closed completely and straight.

Let me know if you have further problems.

Dan

Jan 14, 2009 | Hitachi UltraVision CineForm 55VG825 55"...

2 Answers

TV and Vedio-Projection televisions


what i would do is crack into the tv and watch the individual parts being careful not to unplug anything while you take the back panel off.....turn it on and see what happens. let me know what happens

Sep 30, 2008 | Televison & Video

1 Answer

My Panasonic PT- 50LC13 doesn't turn on


Your service manual on page 82 steps you through decoding the blinking
1) there are two lights on the front near the reciever of the remote signals (Temp indicator and Lamp Indicator)
2) If the Temp indicator is on then they recommend you contact a service center
3) If the Lamp indicator is on and the power light stays on (no blinking) then you need to replace the lamp. Otherwise it says to contact the service center.
4) Counting blinks with the lamp indicator (1 every 5sec - lamp will not light or is abnormal, 2 every 5sec - lamp voltage is abnormal, 3 every 5sec - lamp temp is too high, 4 every 5sec - other error)

Apr 26, 2008 | Panasonic PT-50LC13 50" Rear Projection...

3 Answers

Need answers


The fan may have went bad. If it's out of warranty you may open it up and try and blow some dust out of the fan to see it that may do the trick if not it may need to be replaced. Westexaudioelectronics.com

Oct 04, 2007 | Televison & Video

Not finding what you are looking for?
Hitachi 42V715 42" HDTV Logo

141 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hitachi Televison & Video Experts

Jaime Hernandez

Level 3 Expert

2315 Answers

The Knight
The Knight

Level 3 Expert

73698 Answers

matt martin
matt martin

Level 3 Expert

1208 Answers

Are you a Hitachi Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...