Question about Barebone Systems

1 Answer

I have a fine line across some of my printing. I am using and hp psc 1205 all in one printer. What could be the problem and how can I solve it.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 46 Answers

Usually a line across your printing indicates a bad inkjet head. Luckily on HP printers the printer head is built into the inkjet cartridge. Have you replaced the cartridge? Does it do this on any color or a particular color?

My advise is to replace the cartridges and perform an alignment. If that doesnt fix it, it could be a bad board.

Posted on Feb 21, 2008

  • Brad Nelson Mar 15, 2008

    Did this fix your problem? Can you rate my solution?



    Thanks,

    Brad Nelson

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

I own a HP psc 1350 All-In-One that has given me no problems in the years that I have owned it. However, the other day my toddler reached in and pulled out a thin plastic band (Approx. 14" long and...


hi
it is i think data cable replace it.
very simpleto fix it.
connect its copper end to printer circuit and cartridge tray
then done it.
best of luck

Mar 26, 2008 | Barebone Systems

1 Answer

Hi I have just inserted a new HP ink cartridge 94 into my HP PSC 2350, as the ink was running low. I was printing photos, which keept printing with a red line throughout the picture. After inserting the...


Try opening the printer properties and cleaning the print heads (should probably be done each time a cartridge is changed), it uses some ink up but should clean the build up from running the previous cartridge dry and hopefully solve your printing problem.

Good luck.

Mar 29, 2008 | Barebone Systems

1 Answer

I have a hp psc 2210 all in one printer/scanner etc. im getting ( press enter to align cartridges ) unable to correct, unit will not print.


Press and Hold the 'Setup' button while you press the 'Options' button. This will bypass the error and allow you to print.
You may want to tape a note on the printer with these instructions as this is a frequent problem on the one I have :)

Mar 13, 2008 | Barebone Systems

1 Answer

HI,got this new hp psc 1410 i have connected with my computer ,got photos ready but when i presse print it doesnt work,pls can you help.thanks


did you install the cd driver of your Hp psc 1410?
if not insert the cd driver of your HP printer, after auto play goes click install driver, just follow the instruction on screen, then finish,
remove the ink cartridge, check if ther a cover in the contact point of your cartridge, remove the seal,

Mar 12, 2008 | Barebone Systems

1 Answer

HP PSC 1400 will not print documents on computer.


check your printer head and replace it or runn a clean up on it

Mar 09, 2008 | Barebone Systems

1 Answer

Cannot install printer software ,tells me a newer version of software is already installed .this is a HP pavilion computer using windows xp home addition and a hp psc 1350 all in one. I uninstalled the...


Hi,
try uninstalling any software relating to the printer.
shutdown the computer. Remove any printer to computer cables. Re-boot ( startup ) the computer.
let it set itself up. then shutdown.
turn off the power to computer, put your printer cable back in, as if you were installing it for the first time.
the computer should have found new hardware ( your printer ) And ask for a driver. ensure your HP disk is in the drive, and ask to search Drive D:- Or E:- wherever your CD is located.
If it,s already got the latest drivers installed, i would,nt worry unless your printers not functioning correctly.
Mike @ Compurepair.

Feb 19, 2008 | Barebone Systems

1 Answer

HP Printer Conflict


Perform a clean and "No bloated" installation of the hardware.
Uninstall ALL the HP printer software, disconnect the PSC and reboot the computer.
When windows finish to load, connect the PSC again, the new hardware wizard will show up, follow the instructions with the HP Installation disk in the drive.
IMPORTANT: When a silver sand glass show up in the screen, CANCEL the installation of the HP software (this is by clicking "CANCEL" button or by no accepting the license terms). This will install only the PSC Drivers and nothing else.
Try printing again.

Feb 15, 2008 | Barebone Systems

1 Answer

My HP Deskjet F4140 was working fine until I got a piece of paper stuck. I removed and now it wont print. States printer off line and can not print a test page. IT will copy however.


Turn it off. Unplug the power cord from the printer & usb wait a minute. Plug USB in & than the power cable & turn it on. Next
Open the Printers folder.
Right-click the icon of the printer in use, and then click Open .
Click Printer on the menu, and then ensure that there are no checkmarks next to Pause Printing or Use Printer Offline . If a checkmark is present on either, click the menu option to remove it. If the menu shows Use Printer Online , click that option.

Jan 31, 2008 | Barebone Systems

Not finding what you are looking for?
Barebone Systems Logo

Related Topics:

62 people viewed this question

Ask a Question

Usually answered in minutes!

Top Barebone Systems Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18297 Answers

john smith

Level 2 Expert

366 Answers

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Are you a Barebone System Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...