Question about Barebone Systems

1 Answer

I can not print my wokr - Barebone Systems

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,019 Answers

Hi,
please be more specific.
i,m assuming you cannot print your Work ?
check that all of the cables are correctly fitted, between the computer and printer.
And also that you are getting a power light on the printer itself.
if not check the fuse in the plug.
if it,s software ( program ) related. try using another program to print from.
hope this helps, it,s very difficult to solve any problems.
with lack of information and poor spelling.
Don,t Wokr too hrad.
Mike @ Compurepair :)

Posted on Feb 21, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My printer is new, when I am printing /photocopying and even printing default test page, the print output is very light in the way where one cannot see. Please help, i am stuck on my first day


Go into the printer properties and set the default on the print type you want. It sounds as if you are printing in "Draft" mode which saves ink.

Apr 11, 2012 | General Barebone Systems

2 Answers

I no longer have my manual, how do I change the ink cartridges for the HP Officejet 6300 all-in-one?


To replace the print cartridges
1. Make sure the HP All-in-One is on.
Caution If the HP All-in-One is off when you open the print cartridge door
to access the print cartridges, the HP All-in-One will not release the
cartridges for changing. You might damage the HP All-in-One if the print
cartridges are not docked safely on the right side when you try to remove
them.
2. Open the print cartridge door.
The print carriage moves to the far right side of the HP All-in-One.
3. Wait until the print carriage is idle and silent, and then lightly press down on a
print cartridge to release it.
If you are replacing the tri-color print cartridge, remove the print cartridge from the
slot on the left.
If you are replacing the black or photo print cartridge, remove the print cartridge
from the slot on the right.
4. Pull the print cartridge toward you out of its slot.
5. If you are removing the black print cartridge in order to install the photo print
cartridge, store the black print cartridge in the print cartridge protector or an
airtight plastic container.
If you are removing the print cartridge because it is low or out of ink, recycle the
print cartridge. The HP Inkjet Supplies Recycling Program is available in many
countries/regions, and lets you recycle used print cartridges free of charge. For
more information, go to the following website:
www.hp.com/hpinfo/globalcitizenship/environment/recycle/inkjet.html
6. Remove the new print cartridge from its packaging and, being careful to touch
only the black plastic, gently remove the plastic tape by using the pink pull tab.
7. Slide the new print cartridge forward into the empty slot. Then gently push on the
upper part of the print cartridge forward until it clicks into the socket.
If you are installing the tri-color print cartridge, slide it into the left slot.
If you are installing a black or photo print cartridge, slide it into the right slot.
8. Close the print cartridge door
9. If you installed a new print cartridge, the print cartridge alignment process begins.
10. Make sure you have plain paper loaded in the input tray, and then press OK.
11. The HP All-in-One aligns the print cartridges. Recycle or discard the print
cartridge alignment sheet.
12. Press OK.

Jul 17, 2011 | Barebone Systems

1 Answer

I cant print with my lexmark printer, it is a type x2480 every time i go to print it wants me to set up a fax line please help me


Check your printer properties to make sure it is set to print using the proper port. If it is set to 'print to fax' it will attempt to install a fax line every time you try to print. It should be set to your LPT (printer) port or your USB port, depending on how you have it connected to your computer.

Mar 18, 2008 | Barebone Systems

2 Answers

Our Canon Selphy DS810 is not printing any color on the photo paper. I cleaned it several weeks ago, we have a new ink cartridge in and nothing. It was printing a light yellow color several weeks ago...


There are all kinds of printers and printing problems. It’s important to note at the outset that for safety reasons you should unplug your printer if you plan on working inside the device for any reason. In addition to the electrical hazard, printers (especially laser printers) can also be very hot on the inside, so use caution.

There are a few general troubleshooting steps you should take first, regardless of your printing problem. These will help solve most everyday printing issues.

Reboot. You’ll be amazed at how many printing problems simply disappear after you restart your computer. Also, reboot your printer. Sometimes, for no good reason, a printer will become wedged (it just stops communicating with the computer). Turning your printer off for a few seconds, and then back on, will usually get you going again.

Read the printer’s lights. Doing this can provide you with very useful clues. Is the power light on? Is the paper feed light blinking? Don’t be afraid to press buttons on the printer: Turn it off and on, reset the paper feed, and take the printer offline and bring it online again.

Check your physical connections. Is the power cord loose? Does the cable from the printer to the PC have a secure connection at both ends? Look at the connector pins on your cable. Are they bent? Try another cable if you have one. Check the print cartridges and printing mechanism. Is anything blocking the printer? Are the cartridges firmly in place?

Print a Windows test page. Access your printer’s Properties dialog box (follow the directions given above). Select the General tab and click the Print Test Page button. If nothing else, you can find out a good deal about your printer’s problem. If the test page prints, you have a problem with your application, not with Windows. Answer the questions as prompted and work through Windows’ Print Troubleshooter as needed.

Drivers. Verify drivers on the Details tab in the Printer Properties dialog box. Make sure the installed driver corresponds with your actual printer. Check the manufacturer’s Web site for updated drivers and browse the support pages on the site while you’re there.

Mar 06, 2008 | Barebone Systems

1 Answer

Double sided printing


There should be a setting in the 2-sided properties for binding orientation.

For a MAC, do this:

On the File menu, click Print.
Open the Two-Sided Printing panel.
Select the option to print on both sides.
Select the binding orientation by clicking the appropriate icon.
Change any other settings, and then click Print.

Feb 26, 2008 | Barebone Systems

1 Answer

I am using visita when i try to print i get msg save file but i dont want to save just print so it will not let me print even if i save still msg come back no permiision or something like this and do not...


Hi,
Check to see if you have your printer installed correctly with vista drivers and also make sure that the printer is the default device for printing

Feb 12, 2008 | Barebone Systems

1 Answer

I have a Canon Pixma IP 5000 inkjet printer and am using Mac OS 10.3.9. It has 5 ink cartridges: 2 black (3e and 6) and one each yellow, magenta and cyan. I use it all day every day. After printing...


Thanks for getting back to me.
Sorry this ain't a solution but it seems to be the only cash-free way to contact you. No problem not solved - though I have tried everything. Dismantled the printer; washed, dried and replaced the waste ink pads; washed the print head; blew compressed air through the print-head sponge; replaced the cartridge 3 times; printed hundreds of test prints. I can't think of anything else to do and so I think the only solution is to replace the printhead (probably not even available) or replace the printer. The latter is looking most likely.

Feb 10, 2008 | Barebone Systems

Not finding what you are looking for?
Barebone Systems Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Barebone Systems Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18298 Answers

john smith

Level 2 Expert

366 Answers

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Are you a Barebone System Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...