Question about Thomson 27980GE3 2.4 GHz 1-Line Corded Phone

4 Answers

I get a light on the handset but there is no tone. One time I got a series of oooo and ppppoooo. The handset is laying on its back and when I pass my hand over the earpiece there is a beep from the phone.

Posted by on

  • 1 more comment 
  • vincit_verit Feb 04, 2010

    I can find nothing in the owner's instructions about that.

    How do I go about re-registering the handset?


  • vincit_verit Feb 06, 2010

    It was suggested that my handset was de-registered from the base. I WILL take it for repairs if RE-registering the handset doesn't work.

    How do I register the set with the base?

    Jim…




  • vincit_verit Feb 10, 2010

    I do have a wireless keyboard and mouse. Removed the batteries from them and disconnected two wireless phones in living room, and EUREKA! the handset is now working. If It should happen again then I will do a process of elimination until I find the electronic device(s) creating the problem.

    I however don't know how I could prevent this from happening again. Or is this a rare occurrence?

    I do thank you for your assistance.


×

4 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,069 Answers

I would recommend you perform a factory restore first. to do this, follow these steps;
Factory Default
This feature allows you to restore the handset’s original features.
1. Press the FLASH/CALL WAIT/PROGRAM button until DEFAULT shows in the display.
2. Use the CID/VOL (< or > )button to scroll to YES. The default setting is NO.
3. Press FLASH/CALL WAIT/PROGRAM to confirm. You will hear a confirmation tone.

Regards

Posted on Feb 10, 2010

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,418 Answers

Just of the wall, do you have a wireless mouse and keyboard in the house? Some manufactures of these devices use the same or very close frequency, this may have caused the unregister or your phone to the base. Unhook any other wireless devices in the house, remove the batteries from the phone and the handset, unhook the phone wire from the wall, disconect the power to the phone base and restart all as new, see if that will re-register your handset to the base.

Posted on Feb 07, 2010

  • John Fourteen Six Feb 09, 2010

    Hello vincit_verit have you fixed your phone? I would like to know for future reference.

×

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,428 Answers

There are some internal damages on the phone board. Could be some chip lines have gone bad.

Please consult a service center in your location for repairs and I bet it won't cost much.

Take good care it's a nice product you've got.

Thanks for using Fixya and remember to rate this suggestion.

cheers.

Posted on Feb 05, 2010

  • Titilayo Sodipe Feb 05, 2010

    Have you seen a service center expert?

    I care.


  • Titilayo Sodipe Feb 07, 2010

    Okay......

×

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 15,935 Answers

Has the handset become de-registered from the base?

Thanks

Posted on Feb 04, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

CANT GET PHONE TO HAVE A DIAL TONE OR HEAR THEM


Is the base unit plugged in and have a light to tell you it is powered? Is the battery in the handset in there and connected? Little switch on the phone has to be set to 'pulse'.

It needs to charge for 12 hours before use.

Nov 15, 2015 | Uniden DECT1560 Series Phone

2 Answers

I need to turn of fwd/dnd


Take the handset off the hook, then press the FWD/DND button followed by 0 (zero). When you hear the tone, hang the handset back up. This will work with the PT (Panasonic Proprietary telephone) system. (Alternatively, pick up the handset, press 7 (seven) 1 (one) 0 (zero) 0 (zero) and hang up after the tone. This works for PT and SLT phones (single line telephone))

The same sequence works to cancel call forwarding (except for follow me forwarding). In the Follow me mode, pick up the handset, press FWD/DND or 7 1 0 followed by 8 and the extension number. Then hang up after hearing the tone.

I hope this helps.

Cindy Wells

Sep 23, 2010 | Panasonic KX-T7130 Corded Phone

1 Answer

Cannot program, menu stuck on Spanish, cannot access main menu from mute/ok button


I know this should be a MUCH more techie answer, but have you tried just asking a nearby Mexican to help you? Just a thought.....

You say you cannot get to the menu from the mute/ok button?

What happens instead?
FROM DA BOOOK looks pretty clear to me.

Handset Setup
1. Make sure your phone is OFF (not in TALK mode).
2. Press the mute/menu OK button to go to the main menu.
3. Press CALLER ID-VOLUME ( 6 or 5) button to scroll to HANDSET SETUP.
4. Press mute/menu OK button to confirm and you may program the following items: Language, Handset Name, Ringer Tone, Ringer Volume, VIP Melody, Key Tone, Set Day/Time, Equalizer, Area Code, Tone/Pulse, Registration, Deregistration and Default Setting.
NOTE: During programming, you may press the END/cancel button at any time to exit the sub-menu and return to the menu.
Language
From the Handset Setup Menu:
1. Press the CALLER ID-VOLUME ( 6 or 5) button to scroll to the SET LANGUAGE sub-menu.
2. Press mute/menu OK button to enter the menu. SET LANGUAGE 1ENG 2FRA 3ESP shows in the display.
3. Use the touch tone pad on the handset to select 1ENG, 2FRA, 3ESP, or use the CALLER ID-VOLUME ( 6 or 5) button to scroll to the desired language. English is the default setting.
4. Press the mute/menu OK button to save your selection. You will hear a confirmation tone and the selected language shows in the display.

Apr 29, 2009 | Uniden Cordless Phone

1 Answer

Uniden 1725 no dial tone


I had the same problem as long as they are plugged in correctly and you put the #2 handset into the #1 cradle to register it to your base then try hanging the phone up several times. These are expandable phones so that I believe you can keep adding other handsets. So sometimes they think you have a few more handsets than you really have so when you hang up it may not know what handset you are hanging up #1 #2 or #3 #4 etc. So I had to keep hanging them up until it finally hung up. Then I had to re install them so it knew I only had 2 hand sets. So then you start from the beginning, like when you took it from the packaging. I hate these phones. I ended up replacing them with different ones. Plus I always keep a rotery phone laying around put away because during a power outage you still can plug in an old dial phone and it will work! Nothing like old technology.

Feb 15, 2009 | Uniden 5.8GHz Dual Cordless Phone

1 Answer

Handset


I guess its time to get new batteries

Sep 23, 2008 | Sony SPP AQ600 Cordless Phone

1 Answer

Bought phone EX18560 Series yesterday. floolowed instructions to charge. Today I came home from work, plugged in telephone jack. phone will not turn on. Attempted to re-register (4X's). Led flashes....


I have two older (2002) model cordless Uniden phones that require the handsets to return to their original factory bases. If they have rested on another Uniden base, even of the same model, there is no dialup tone. Replace to the original base and you should be back in service.

Aug 11, 2008 | Uniden Lands Phones

1 Answer

Vtech,5.8 3-phone w/digital recorder, model DS4122-3 None of the phones work they either say connecting or put back in the charger . these are only 2 months old?


To deregister ALL handsets:
Step 1: Press and hold FIND HANDSET on the main telephone base for 10 seconds.

Step 2: When the IN USE light starts to flash, release the FIND HANDSET button.

Step 3: Press and release FIND HANDSET again. The IN USE light will turn off and in a few seconds, all handsets will be de-registered.

Step 4: All handsets will show NOT REGISTERED.

To register a handset (register 1 handset at a time):
Step 1: Place the handset in the base unit or a charger that is connected to a power outlet. If PRESS FIND HNDST 4 SEC ON BASE does not appear on the screen after a few seconds, lift up handset and place in base or charger again.

Step 2: On the telephone base, press and hold FIND HANDSET for four seconds. Release FIND HANDSET once the IN USE light comes on.

After a while the handset will emit a series of tones, the newly registered handset will be assigned the lowest extension number not previously assigned to another system handset (1-4) when successfully registered. Repeat Steps 1 and 2 if the handset does not successfully register to the telephone base within two minutes.

REPEAT THE REGISTRATION PROCEDURE FOR EACH SYSTEM HANDSET.

Make sure the handsets are not receiving interference from other appliances, cell phones, etc.

IF deregistering does not work .. you will need to reset the entire system
Step 1: Disconnect the power to the telephone base.

Step 2: Disconnect the handset battery.

Step 3: Wait a few minutes and then reconnect the power to the telephone base.

Step 4: Reconnect the handset battery

Step 5: Wait about one minute for the handset to re-establish a link with the telephone base and then test the phone again.
You will need to set the time and date again after resetting the entire system.

Mar 11, 2008 | Lands Phones

2 Answers

VTech 5.8 mhz won't work


I found a solution that fixed this problem (at least for me). On the vtech site they said to unplug the base unit for at least 5 minutes. Previously, I had only unplugged the base unit for a few seconds. This time, I left it unplugged for about 10 minutes or so and when I plugged it back in, everything was working fine. Apparently there is some sort of capacitor that must discharge long enough to completely remove power from the circuitry.

Good luck and I hope this works for you!

Jan 18, 2008 | Vtech 9009111 Cordless Phone

1 Answer

Vtech M6896 phones do not work


Step 1: Press and hold FIND HANDSET on the main telephone base for 10 seconds.

Step 2: When the IN USE light starts to flash, release the FIND HANDSET button.

Step 3: Press and release FIND HANDSET again. The IN USE light will turn off and in a few seconds, all handsets will be de-registered.

Step 4: All handsets will show NOT REGISTERED.

To register a handset (register 1 handset at a time):
Step 1: Place the handset in the base unit or a charger that is connected to a power outlet. If PRESS FIND HNDST 4 SEC ON BASE does not appear on the screen after a few seconds, lift up handset and place in base or charger again.

Step 2: On the telephone base, press and hold FIND HANDSET for four seconds. Release FIND HANDSET once the IN USE light comes on.

After a while the handset will emit a series of tones, the newly registered handset will be assigned the lowest extension number not previously assigned to another system handset (1-4) when successfully registered. Repeat Steps 1 and 2 if the handset does not successfully register to the telephone base within two minutes.

Jan 18, 2008 | Vtech mi6896 Trio Cordless Phone

1 Answer

Handset has No link to base


I was having the same problem with the same model phone, and fixed the problem by rebooting the phone – unplugging the AC and phone cord from the base station and plugging both back it, then removing and replacing the handset to regenerate the security code.

Nov 17, 2007 | Xact Communication XG2200 Cordless Phone

Not finding what you are looking for?
Thomson 27980GE3 2.4 GHz 1-Line Corded Phone Logo

Related Topics:

53 people viewed this question

Ask a Question

Usually answered in minutes!

Top Thomson Lands Phones Experts

kakima

Level 3 Expert

102366 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18389 Answers

george  peters
george peters

Level 3 Expert

860 Answers

Are you a Thomson Lands Phone Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...