I have Starmen P/S TOM202CBB IN my Digital Research 32"LCD TV Factory advises I am not getting 5v to pin CN1.need new P/S??

Sounds like a bad power supply board. There is a repair service which addresses any problem with the power supply board, not just bad capacitors: http://www.coppelltvrepair.com/p/777/starmen-tom202cabb-power-supply-board-repair-service-no-power-shutdown-etc

HOLA AMIGO PASABA POR AQUI Y MIRE TU INQUIETUD
DEJAME COMENTARTE QUE PARA ESTA MARCA LAS PARTES ESTAN MUY LIMITADAS CASI SIEMPRE TIENEN QUE SER USADAS YA QUE ESTA COMPANIA NO ASE PARTES!
PUES BUENO MUCHA SUERTE POR CIERTO TRATA EN EBAY.COM SI REQUIERES MAS INFORMACION AQUI ME ENCUENTRAS!
WWW.TV-SOLUTIONS.REDTIENDA.NET

Tries the tv and cable box unplug,replug it back an hour later.Let the tv reset it self back to factory setting.The cable box upgrade it software.The tv should,work now.Not,than the tv power supply board have problems.That the board,where the power a/c cord plug into it.Tries websites like Shopjimmy.com,Ebay.com to buy a refurbish power supply board for the replacement.

Does this particular television have a digital tuner built in? If this is the case, try to search for your channels. There should be a section in the manual for this. If you have an external tuner, check and make sure you have the correct input selected and then change the channels on that device rather than the television.

what is the code for soyo tv 32" lcd to activate my digital remote to use it for all functions instead of using two remotes one to turn off and on and the other to navigate.

My sharp tv also had a green tint and resetting to facotry setting did not work, what finally worked is making sure that all cables were inserted all the way into the tv and receiver. Someone else advised this for another Tv and it worked on my sharp so it is worth a try.

yes.

This requires skill though

If the LCD glass is broken (you see line, stripes, and the watery like drips) it is probably going to be easier to get a new TV.

Anyway, look on ebay for any TV of the same model with a non-functioning backlight, You can use your backlight with the glass from the new TV. You may have broken bulbs so you can swap these to.

OPTION 2. Dissasemble TV to the panel. Find out who makes the panel; it will be LG, Samsung, CMO, AUO, Sharp, something. Find a 32" TV that uses the same manufacturers panel on ebay(this will be difficult but possible with research).

BEWARE.....
1. You must utilize 720P TV panel to replace your 720P panel. 1080P for 1080P and so on

2. LVDS (video signal) will be similar for all TVs except....voltages may be different in case of 32" panel. They will be 6VDC, 9VDC or 12VDC. Also sometimes the cable is reversed from panel to panel. This means that you should be using the original LVDS cable from the Panel you are using the Glass (including the Drive PWB) for.

1 and 2 are kindof technical so sorry if I didn't explain enough. Just know that if you didn't understand it, I suggest doing a lot of research and question asking before trying or you may damage something.

If you are just swapping from 1 TV same model and LCD panel to your TV having being same model or using the same LCD panel...you probably don't have much to worry about.

Good Luck

I've done a little research and I don.t see where you have a ATSC tuner that receives the over the air digital signal. You have a basic Analog tuner. The only way you can receive digital is by a HD cable box by having cable or going to Satellite.

take apart the lcd and find the lcd panel number then email patel150@gmail.com to buy a new panel from a factory in china
then put it all together

If you can do it yourself replace C31 (1000 25v) also good idea to replace C32,35 also (1000 uf 25v). Theres also C33 (680 uf 25) if you want to replace it.