Question about Computers & Internet

1 Answer

Wireing diagram for cutler hammer chgenlc200ats1

Can anyone help me ?

Posted by on

  • Niteesh Ahire
    Niteesh Ahire May 11, 2010

    WHAT IS YOUR PROBLEM

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 65 Answers

Tell me your problem

Posted on Feb 23, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How To wire a cutler-hammer A/C Disconnect Box 60amp-240V Non- Fusible


"LINE" is typically the incoming power.

"LOAD" is typically the outgoing wires to the machine.

Sep 19, 2014 | Cutler Hammer DPU222RGF 60 Amp Out A/C...

1 Answer

Have a cutler-hammer 210 responder drive inside the box is a relay marked NJ it is going bad how do I find the # to replace it THANKS


There should be information on the relay itself. Boettchers in Beloit handle Cutler Hammer (Eaton) products. You may be able to pull the relay and take it to them for an exact replacement.

Feb 17, 2012 | Cutler Hammer Electrical Supplies

1 Answer

Arc fault breaker trips when you turn florescent and can lights on


Sounds like something is wrong with the light check the wiring. Unhook the light and try ther breaker if breaker does not trip then problem is in the circuit.

Jul 24, 2011 | Cutler Hammer "CUTLER HAMMER" ARC FAULT...

1 Answer

Cutler Hammer 20 Arc Fault breaker for bedroom outlets will not reset after activating test switch.


The circuit breaker must be turned to the "off" position first from the middle position, and then to the "on" position. The cutler hammer arc breakers carry a lifetime warranty so if it will not reset you may want to contact the manufacture.

Oct 24, 2010 | Cutler Hammer BR120AF BREAKER CIRCUIT BR 1...

1 Answer

Wire diagram for fusible pullout a/c disconnect.


THERE IS ONLY THE WIRES GOING IN AND THE WIRE GOING OUT THAT IS HOW THIS WORKS

Jan 07, 2010 | Cutler Hammer Fusible AC Disconnect Switch...

1 Answer

Need a wiring diagram for a cutler hammer 100 amp double throw safetey switch the box came with no manual


Line voltage (source power) goes to the lugs on the top and load (goes to the device) is on the bottom. If it is designed for single-phase power (with a neutral), there should be an isolated block with lugs for neutral, but if it is not, just get an inline lug (available at a hardware store like Home Depot) to connect your neutrals and then insulate it with electrical or rubber insulating tape. Then you will need to bond your grounds (from the source AND to the device) to the can.

Nov 06, 2009 | Cutler Hammer Electrical Supplies

1 Answer

CAN A EHD1020 CIRCUIT BREAKER (CUTLER HAMMER) BE USED IN A 120/240 APPLICATION? BREAKER IS IN A SFDN100 ENCLOSURE (CUTLER HAMMER)


For 240 if it is a single pole breaker then no. You need a double pole breaker or 2 single breakers , one above the other, connect the red wire to one and the black wire to the other. this way you are drawing from both legs. hope this helps you...

Sep 15, 2009 | Cutler Hammer Eaton Electical #BD3030...

1 Answer

Need wiring info for cutler hammer C25DND330 30amp fire shunt breaker...need to shunt 4/220's and 1/110 can you help


Probably easier and about the same price to just buy a shunt trip main breaker. IIRC, code usually requires that anyway.

As far as the c25dnd330, it's just a regular 3 pole contactor, each pole is good for 30 amps. The three poles are L1,2,&3>>>T1,2,&3. The other two contacts are the control coil. I believe your model is 120 volt (most are)....the voltage should be stamped somewhere near the contacts.

Jan 29, 2009 | Cutler Hammer Cutler-Hammer No.BR48L125RP...

Not finding what you are looking for?
Computers & Internet Logo

Related Topics:

83 people viewed this question

Ask a Question

Usually answered in minutes!

Top Computers & Internet Experts

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

kakima

Level 3 Expert

102366 Answers

David Payne
David Payne

Level 3 Expert

14161 Answers

Are you a Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...