Question about Landice L 7CLUB Executive Trainer Treadmill

1 Answer

I have a ten year old lightly used Landice L7 treadmill. A couple of years ago it started clicking when turned on and took 3-5 minutes before the belt started moving. After it was moving I had to wait a few minutes more before starting to walk on it as it would stop if I got on it too soon. Yesterday it started the same but it clicked for about 7-8 minutes then the belt would start to move and almost immediatly stop with a message about the elevation. I tried it a few times and finally the belt stared turning and ran for about 30 seconds and quit with a message about the speed. Today The belt doesn't even start turning.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 10,865 Answers

Hello CaptJack. Your treadmill is need of a major tuneup. Contact landice at http://landice.com/Pages/contact_home.html
They will be able to direct you to their nearest service center.....or you might ask them if they take turn-ins against rebuilt models........... Regards, Joe

Posted on Feb 03, 2010

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

maxtreadmill
  • 832 Answers

SOURCE: Landice L7 gives me a L5 reading on the screen

Your L7 error looks like L5 , but its really LS which mean lost signal. Unplug unit take motor shroud off then plug unit back in wall outlet. When looking in front unit you will see a Motor control board and there are LED lit up one of them should be an amber light this is you speed sensor which is attached to the top of your motor. Manually rotate the fly wheel and see if that light flickers if it does then your speed sensor is working properly if not replace speed sensor. The next thing to look at is the motor brushes to if they are worn unplug unit you should see slitted caps on both side of motor remove them if they are less than 3/8" they need replacing. That for the most parts should take of your problem. Call Landice @ 1800-526-3423 have the serial# handy their on all the components in the unit

Posted on Feb 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Display will not light up. Board has a green light.


Please test the REED switch, for open or fault. Clean it, and tight the connector very well. See the diagram attached.
2) Tight the ribbon cables, clean it for keypads.
3) Replace old batteries by new ones, clean the contacts batteries very well. and try again. see the block diagram
4)Run the software calibration for troubleshooting,
God bless you2_4_2013_4_45_22_pm.gif2_4_2013_4_45_37_pm.gif

Feb 04, 2013 | Landice L7 LTd Pro Sports Trainer...

1 Answer

Landice L7 treadmill won't turn on


1)LUBE the deck belt, maybe you have a deck belt worn, by lack maintenance.
2) Lube the rollers bearings, in according with the maintenance schedule.
3) Test the main motor for voltage input, if there are the motor need repair.
4) Test the output voltage board, for input voltage motor, if there are NOT the board is faulty.
5) After fixing RUN the software calibration for diagnose, and troubleshooting.

5_9_2012_11_02_56_am.gif

May 08, 2012 | Landice L7 Executive Trainer Treadmill...

1 Answer

With the L7 plugged in, and after pressing the start button, nothing lights up and the belt does not move.


looking for a qualified technician to check the connectors on the lower board specifically where the motor wires connected.
this part of the lower board overheats and sometimes there are false contact.

Aug 25, 2010 | Landice L7 LTd Pro Sports Trainer...

1 Answer

Landice L7 gives me a L5 reading on the screen


Your L7 error looks like L5 , but its really LS which mean lost signal. Unplug unit take motor shroud off then plug unit back in wall outlet. When looking in front unit you will see a Motor control board and there are LED lit up one of them should be an amber light this is you speed sensor which is attached to the top of your motor. Manually rotate the fly wheel and see if that light flickers if it does then your speed sensor is working properly if not replace speed sensor. The next thing to look at is the motor brushes to if they are worn unplug unit you should see slitted caps on both side of motor remove them if they are less than 3/8" they need replacing. That for the most parts should take of your problem. Call Landice @ 1800-526-3423 have the serial# handy their on all the components in the unit

Feb 12, 2010 | Landice L7 LTd Pro Sports Trainer...

1 Answer

Landice treadmill


You may want to take off you head board and check all the connection. this is not hard to do. Also when you in there check you cable connection. can you do this?

Jan 10, 2009 | Landice Pro Sport Trainer Treadmill

Not finding what you are looking for?
Landice L 7CLUB Executive Trainer Treadmill Logo

Related Topics:

106 people viewed this question

Ask a Question

Usually answered in minutes!

Top Landice Exercise & Fitness Experts

Sportsmith LLC
Sportsmith LLC

Level 3 Expert

914 Answers

Tom Chichester

Level 3 Expert

33359 Answers

Brian Woods

Level 1 Expert

19 Answers

Are you a Landice Exercise and Fitnes Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...