Question about HP LaserJet 3055 All-In-One Printer

1 Answer

HP3055 Its getting memory full error every other day after resetting firmware

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 123 Answers

Hi Have you tried to do a factory reset on it, incase anything is stuck in the onboard memory, you could also check the memory settings in the printer management menu.

Posted on Feb 19, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Getting 79 ERROR on CM1015 printer. Printer shows error then powers off and repeats.


Error 79 indicates a internal memory error, specifically, it can indicate the internal memory is full. You can try printing the printer's test page, it shouldn't fill the memory and it should print. Here's a link to the official HP error 79 trouble shooting instructions for the CM1015.

HP Color LaserJet CM1015 MFP and CM1017 MFP Series Printers Control Panel...

Jan 25, 2015 | HP LaserJet CM1015 All-In-One Printer

1 Answer

Memory full error c230


up grade the memory and or have a tech come out re flash the firmware in the machine also might need to have the memory cleared

Mar 13, 2014 | Konica Minolta Printers & Copiers

1 Answer

FS3140 memory full


this can occur if jobs hang due to printer error (empty toner, jam, etc...) if the printer usually prints normally but displays that message when faxes are being received then you may need to reset or replace the fax board and update the firmware. you could turn on hdd RAMDISK mode in the command center. You could also add additional RAM

Feb 19, 2013 | Kyocera FS3140MFP AllInOne Laser Printer

1 Answer

Error message 59.90


Firmware error, try perform a cold reset on the printer.
Turn off and on the power switch, when printer start count memory press enter button until select language came up in display, release the enter button, use the arrow until cold reset is displayed, press enter and the printer will reboot. When the printer goes to ready upgrade firmware on it.

Feb 16, 2011 | HP DeskJet 5550 InkJet Printer

1 Answer

Pcl6 error - false


Some ideas.
First , go to the back of the machine, there is a panel about 6 inches square with a couple of tabs on it to remove that panel. Turn the machine off, remove the panel. Remove BOTH memory sticks. With the memory sticks removed, turn the machine back on and let it come to ready. Then reinsert the memory sticks and power the machine back on.

Second, Go to Xerox.com. Click downloads and drivers. Then enter M20i in the search box. Go to downloads and drivers and scroll down to the FIRMWARE download, It should probably be version 2.9. May be higher like 3.1. Anyhow, Download the newest version of machine firmware and install it on your machine.
Other things to try if one of the first 2 dont help.

Change the ethernet speed (auto, 10M half, 10M full, 100M half, 100M full)
Reset NIC card
Reset copier back to factory default
Clear all the memory in copier

Mar 29, 2010 | Xerox WorkCentre M20i All-In-One Laser...

1 Answer

Error 49.4401


Hi I only know that error 49.
But you can try this it may help
A 49 error is a firmware error, it might be caused by the firmware itself, or by the failure of a printer module.

How to isolate the cause:

- Verify that the problem is not being caused by a specific job, this error can be caused by bad information being sent to the printer.
- Power off and remove any installed EIO devices, (JetDirect Cards, Hard Drives), power on and test.

Cold Reset the printer:

- Power off, remove any optional memory, power on and retest.
- Power off and reseat any memory and firmware modules on the formatter board, power on and test.
- Power off, reseat the formatter board, power on and test.

Check firmware version: on newer machines with flashable firmware upgrade to the latest version. If you are running the latest version reload it, this might fix corrupted firmware. (Some printers have flashable firmware, others use a Firmware DIMM which must be replaced to upgrade.)


If you haven't found the cause yet it's time to start swapping parts:

- Firmware module if it's a DIMM as opposed to being part of the formatter.
- Memory if installed, some printers have to have at least one memory module installed to run, and it must have enough capacity to function, in some cases installing a module that does not meet the minimum requirements of the machine will cause a 49 error

Jan 19, 2010 | HP Color LaserJet 4650DTN Printer

2 Answers

49 error turn off then on problem:


pls perform these steps
1
Remove all memory DIMMs or thirdparty
DIMMs from the printer. (Do not
remove the firmware DIMM in the lower
slot J1).
2
Remove the printer EIO card.
3 turn the printer on
4 If the error does not persist, install each
DIMM and EIO device one at a time.
Turn the printer off and then on again
after installing each device.
5 Replace DIMMs and EIO devices as
necessary.
10. Reconnect all of the printer cables.
11. If the error persists, replace the firmware dimm
& calibrate the printer
ur problem will be resolve

Dec 18, 2009 | HP LaserJet 2700n Printer

1 Answer

Service Error 49 FF04


A 49 error is a firmware error, it might be caused by the firmware itself, or by the failure of a printer module.

How to isolate the cause:

- Verify that the problem is not being caused by a specific job, this error can be caused by bad information being sent to the printer.
- Power off and remove any installed EIO devices, (JetDirect Cards, Hard Drives), power on and test.

Cold Reset the printer:

- Power off, remove any optional memory, power on and retest.
- Power off and reseat any memory and firmware modules on the formatter board, power on and test.
- Power off, reseat the formatter board, power on and test.

Check firmware version: on newer machines with flashable firmware upgrade to the latest version. If you are running the latest version reload it, this might fix corrupted firmware. (Some printers have flashable firmware, others use a Firmware DIMM which must be replaced to upgrade.)


If you haven't found the cause yet it's time to start swapping parts:

- Firmware module if it's a DIMM as opposed to being part of the formatter.
- Memory if installed, some printers have to have at least one memory module installed to run, and it must have enough capacity to function, in some cases installing a module that does not meet the minimum requirements of the machine will cause a 49 error

Dec 11, 2009 | HP LaserJet 2430dtn Printer

1 Answer

Error 409 Memory full on Monarch 9850 printer


409 is a memory full error, so if you have reset the printer, then your memory should be "flushed". You may also have an incorrect flow control, so when you send too much data to the printer, you can get a 409.

Not knowing which your issue could be, try calling the company's support number 1-800-543-6650.

Mar 19, 2009 | Monarch 9850 TABLETOP PRINTER

1 Answer

NVram error


I i knew the model, But what is happening is the machine is not reading the machine ram. One of the memory sticks is print memory and one contains the machine firmware.
In order of likely hood here is what has happened.
1. The memory stick simply needs to be removed and re seated in the slot.
2. The memory itself has failed. Needs to be replaced and the machine firmware reloaded.
3. The machine firmware has corrupted and needs reloaded.
4.You need to to an NVRAM reset.
5. The battery maintaining the memory has failed.
6. The main board in the machine has failed.
7. Corruption, which a reset will remove. Can't tell you how to or if you can do a NVRAM reset without knowing the model number.

Jul 11, 2008 | Xerox Printers & Copiers

Not finding what you are looking for?
HP LaserJet 3055 All-In-One Printer Logo

397 people viewed this question

Ask a Question

Usually answered in minutes!

Top HP Printers & Copiers Experts

kakima

Level 3 Expert

96518 Answers

k24674

Level 3 Expert

7987 Answers

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Are you a HP Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...