Question about Washing Machines

2 Answers

Zanussi jetsystem Turbodry 1200

Hi Washer powers up and all leds work, but when start button is pressed, it keep blinking but dosent start. It was working fine till last week with out any issues. any help please The code er90 keeps coming up in a flashing code. This is driving me nuts. Please help as I have tons of washing to do. Many thanks. Have tried resetting - putting machine off and then on. Making sure the door is shut properly.

Posted by on

  • misspaint Feb 19, 2008

    How do I replace the circuit board

  • misspaint Feb 21, 2008

    Thank you guest. I sent an e-mail to the Zanussi Service Centre but so far they have not responded. Meanwhile the washing is piling up. Do you know the approximate price of a new circuit board? Would I be able to fit same myself without any help?

×

2 Answers

You can ask any service center of your brand and ask for the part then you can do it by your self to replace it. no need to let them repair it. it will cost you a lot of money if they will repair it.and time consuming.

Posted on Feb 21, 2008

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 9 Answers

Replace the circuit board

Posted on Feb 19, 2008

1 Suggested Answer

  • 1 Answer

SOURCE: Zanussi jetsystem Turbodry 1200

Hi, Ive moved into a new flat, and I have a zanussi jet stream 1400 turbo dry front loader. Of course, no instructions were left on how to use it. I cant seem to get anything but soaking wet clothes, no spin cycle, and certainly no turbo dry.

Can you tell me where I could download a users manual?

Posted on Feb 10, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Zanussi jetsystem turbodry 1600 wjs1665 w is not heating the water


More than likely the heater element has failed.
This is located at the rear of the washer drum.
It means removing the rear half of the cabinet to access it.

Mar 29, 2010 | Zanussi ZWF1430W Front Load Washer

1 Answer

The drier won't heat up and it flashes up a number (I'll check tonight again what the number is). it washes fine but won't dry. It is a Zanussi Jetsystem Turbodry 1200.


Hello,

Have you fixed the problem yet? And if yes, how??
I have the same washing machine with the same problem. So I hope you can help me!

Best regards,

Nourah van Leeuwen

Jul 22, 2009 | Washing Machines

1 Answer

Zanussi jetsystem turbodry 1200 door wont open


its the doorcatch,turn power off, remove lid and put hand in machine where doorlock is situated feel about and try open catch, repair or replace?

Jun 24, 2009 | Zanussi ZWF1420W Front Load Washer

1 Answer

What is E 40 on Zanussi Turbodry 1200?


E40 indicates the doors not closed properly. Sometimes it can be the lock itself or the main control board

Nov 24, 2008 | Zanussi FJS1225W Front Load Washer

1 Answer

Zanussi Turbodry 1200 spin problem


if this washer is used alot then it will more then likely be the carbon brushes which u will need to take the lid off undue 4screws out where it joins front to the back screws at the back to the bottom and 1screw either side of the bottom where the panels join together behind a little cap which will have an hole in the middle of it to get it out u will then be able to get to the motor to replace the carbon brushes

Nov 22, 2008 | Zanussi ZJD1219 Front Load Washer / Dryer

1 Answer

Zanusssi jetsystem turbodry 1200


clean out filter, door bottom right, unscrew filter and clean it

Aug 02, 2008 | Zanussi IZ161S Front Load Washer

2 Answers

Zanussi WJS 1397W


possibly a foreign object in pump.
tilt backwards at a good angle and remove pump. i find the easiest way to do this is to undo the 3 screws round the periphery of the pump

Jul 11, 2008 | Zanussi WJS1265W Front Load Washer/Dryer

2 Answers

Zanussi Turbodry jetsystem 1200


hiya
e90 means there is a communication error between the circuit boards inside. remove the plug then take the lid off the machine, remove the block which has the 5 (iirc) blue wires in it and give it a quick squeeze then replace, this should hopefully solve your problem.

hope this helps

please dont forget to rate the helpfulness of this reply, thanks kj

Jul 08, 2008 | Zanussi FJS1225W Front Load Washer

4 Answers

Zanussi jetsystem Turbodry 1200


It appears that you may have a faulty door interlock or a faulty PCB. pcb is not really a DIY job as some boards require proramming on certain versions. Regards Advisor

Oct 30, 2006 | Zanussi FJS1225W Front Load Washer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

621 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...