Question about Sharp AR-5316 Advanced Digital Imager Copier

4 Answers

SHARP AR5316 RESTART CODE - Sharp AR-5316 Advanced Digital Imager Copier

Posted by on

  • 1 more comment 
  • Botez Adrian May 11, 2010

    There is no restart code, what is the problem on the copier?

  • amir hamza
    amir hamza Oct 05, 2012

    simuletion cod #-interput-C-interpuo=14=copy batton

  • amir hamza
    amir hamza Oct 05, 2012

    simuletion cod #-interput-C-interpuo=14=copy batton

×

4 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Sharp AR-5316E shows 02 on the screen what can i do to resolve the error the code error

Posted on Feb 19, 2010

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 35 Answers

# interrupt c interrupt

Posted on Feb 16, 2010

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I want to connect a photocopy machine (Sharp AR 5315) with my computer for printing

Posted on Feb 25, 2010

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Sharp Expert
  • 316 Answers

Simuletion cod #-interput-C-interpuo=14=copy batton

Posted on Oct 20, 2012

  • amir hamza
    amir hamza Jul 19, 2013

    press # interrupt c interrupt . Display goes off press 14

×

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 7 Answers

SOURCE: SHARP AR5316 SHOWING PAPER WHILE NO PAPER JAM

try to chek if the actuator of the exit sensor is ok you will find it when you open the side door exactly attached to the heater try to check the end is it in plase or not if not use sim 30 sub1 to check all sensors you wil solve your problem

Posted on Mar 23, 2009

checkitright
  • 1362 Answers

SOURCE: sharp ar5316 blank pages printed and copied.

while standing in front of the copier open the Right door and then then flip down the Front door. Are the levers in place ? usually the front door will not close properly if not.

Second take out the toner and look for a loosely hanging piece of plastic on it, give it a tug, does it seem to be a long peice of clear plastic? if yes yank it all the way out. It is a protective piece sent for shipping. It will be on ALL the toners you get.

 

If not look at the right side door there is a back assembly there with either a black cylinder type roller or some strings.

Are the strings broken , is the roller in place?

Posted on Oct 25, 2007

  • 2072 Answers

SOURCE: sharp copier AR5316

H2 or 2H is related to a fuser under heat or overheat.
Try this first,

Performing a Fault Reset 14 will reset your WorkCentre and will help to clear error codes.

  1. Find the pink Clear button on the Control Panel of the WorkCentre.
  2. Find the button below the word Auto.
  3. Press these buttons in the following sequence: [Clear], [Auto], [Clear], [Auto] NOTE: All of the lights on the Control Panel should go out and the LED Display should go blank. If the lights do not go out, then repeat step 3 until they do. It may be necessary to increase or decrease the pace of the [Clear], [Auto], [Clear], [Auto] sequence.
  4. Press the [10's] key one time and the [1's] key four times to enter '14' in the LED Display, as if you were to make 14 copies.
  5. Press the green [Start] button.
  6. Press the pink [Clear] button two times.
  7. The WorkCentre should now warm up and come to ready.
  8. If the above steps do not clear the error code, repeat steps 3 to 6 a second time.
If this does not clear the problem the fuser will need replaced.

Posted on Feb 21, 2008

goalie39
  • 469 Answers

SOURCE: getting code H 3

The printer repair guy just left. I'm paraphrasing what he told me:

The Sharp MX4501N was displaying the error: H3-04. This does mean that the printer was reading an above average temperature for the fuser, for some reason.

He said that in his experience, 90% of the time, this is due to power surges/spikes and not an actual incident of the fuser over heating. A good surge protector isn't normally enough and he recommended that we look around for a cheap UPS to condition the power.

Other things that can cause a higher than average reading of the fuser can be caused by paper jams, where a piece or pieces of the paper are lodges inside, insulating the fuser and restricting air flow to the internal compnents. Printing 15-25 blank sheets through the copier can usually dislodge these. If not, call for assistance.

In order to clear the error code (H3-04) from possible powewr surges/pikes, I was given the following code: #P, *, C, 1,4 PRINT
This will remove most of the codes restricting printing to the copier, however, should the code reappear, contact customer service and arrange for a visit from the local repair person.

I hope this helps anyone else who may run in to the same problemThe error: H3-04. This does mean that the printer was reading an above average temperature for the fuser, for some reason.

90% of the time, this is due to Power surges/spikes and not an actual incident of the fuser over heating. A good surge protector isn't normally enough and recommended that we look around for a cheap UPS to condition the power.

Other things that can cause a higher than average reading of the fuser can be caused by paper jams, where a piece or pieces of the paper are lodges inside, insulating the fuser and restricting air flow to the internal compnents. Printing 15-25 blank sheets through the copier can usually dislodge these. If not, call for assistance.

In order to clear the error code (H3-04) from possible power surges/pikes, I was given the following code: #P, *, C, 1,4 PRINT
This will remove most of the codes restricting printing to the copier, however, should the code reappear, contact customer service and arrange for a visit from the local repair person.

I hope this helps anyone else who may run in to the same problem

Posted on May 11, 2009

  • 14 Answers

SOURCE: h3 code in sharp ar5316

It sound like you have a thermistor that either has a buildup on it or it is not contacting the fuser roller. I would remove the fuser, disassy and clean every component. Reinstall and usually the problems go away. Let me know if you need more assistance.

Posted on May 12, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Free xp driver for sharp ar5316 please!


Drivers for Sharp AR-5316 are available at Sharp Official Support site Click here and make selection as under: -

Select AR5316 > Windows XP

Good Luck!
Appreciate generously, if the solution could have been of any help!
CreativeTECH

Dec 19, 2010 | Office Equipment & Supplies

2 Answers

H3 code in sharp ar5316


It sound like you have a thermistor that either has a buildup on it or it is not contacting the fuser roller. I would remove the fuser, disassy and clean every component. Reinstall and usually the problems go away. Let me know if you need more assistance.

May 11, 2009 | Sharp AR-5316 Advanced Digital Imager...

1 Answer

Sharp ar5316 code U2


Try reset code sim 16 in diagnostics.
Type p * c * machine will go into sim mode
type in 16 then start.
press CA
machine will turn off then back on.

Sep 05, 2008 | Sharp AR-5316 Advanced Digital Imager...

1 Answer

E-7 sub code 10


Check connection of the ccd cable to the ccd and the pcu board, if all good the you have problems. try reseting the m/c first

Aug 05, 2008 | Sharp AR-5316 Advanced Digital Imager...

Not finding what you are looking for?
Sharp AR-5316 Advanced Digital Imager Copier Logo

952 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sharp Office Equipment & Supplies Experts

k24674

Level 3 Expert

7993 Answers

CheckitRight
CheckitRight

Level 3 Expert

1362 Answers

kakima

Level 3 Expert

102366 Answers

Are you a Sharp Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...