Lost manual ,cant remember how to keep radio stations on memeory,so as not to keep re-tuning every time when switched on.

Select the AM or FM wave band.
Tune the radio to a station then press and hold down the 1 or 2 or 3 pre tune station button until it beeps. Then this radio station is then set to which pre tune button you have selected.
Repeat to set the buttons for other radio stations.

OK press power on,select tuner button for radio. then select band AM or FM. Then press tuning mode button until you see [manual] in the window. then press the tuning button [arrow left or arrow right buttons] until you get to your desired station.then press program / memory set. a memory number will flash [ say memory 1]. then press program/ memory /set button again to lock in the selection [memory 1] now this is the TRICKY PART. Once the selection is memorized go back to tuning mode Press the tuning mode button until you see manual and i think you can follow the above procedure. If you program AM stations first Then press the BAND button to get FM stations and go back to step one.

From the main menu, select the icon that looks like a little radio
To search for the next stronger signal, press and hold the up or down arrow
To fine tune the frequency, briefly press the up or down arrow

From the main menu, select to enter
radio mode.
• The earphones cable acts as FM
antenna.
Manually tune a radio station
While in mode, you can manually tune to a
radio station:
1 To search for the next stronger signal,
press and hold / .
2 To fine tune the frequency, briefly press
/ .
Auto-tune preset radio
station
The auto-tune feature of GoGear Vibe helps
you find radio stations and save them under the
preset numbers.
1 While in mode, select [Auto tune] >
[Yes].
»» The radio automatically tunes radio
stations and saves the frequencies to
presets.
»» There are 20 presets available.
»» To stop auto tuning, press .
»» To exit radio, press and hold for 2
seconds.
EN

Not very specific. Do you have the manual?

The following is from a VSX-03TXH manual. It ain't pretty but it may help.

I'm posting it in multiple parts due to space contraints.

37

Chapter 6:

Using the tuner

Listening to the radio

The following steps show you how to tune in to FM and

AM radio broadcasts using the automatic (search) and

manual (step) tuning functions. If you already know the

frequency of the station you want, see Tuning directly to a

station below. Once you are tuned to a station you can

memorize the frequency for recall later-see Saving

station presets below for more on how to do this.

1 Press the FM/AM button to select the tuner.

2 Use the FM/AM button to change the band (FM or

AM), if necessary.

Each press switches the band between FM and AM.

3 Tune to a station.

There are three ways to do this:

Automatic tuning

To search for stations in the currently selected band,

press and hold TUNE ?©/?? for about a second. The

receiver will start searching for the next station,

stopping when it has found one. Repeat to search for

other stations.

Manual tuning

To change the frequency one step at a time, press

TUNE ?©/??.

High speed tuning

Press and hold TUNE ?©/?? for high speed tuning.

Release the button at the frequency you want.

Improving FM stereo sound

If the TUNED or STEREO indicators don't light when

tuning to an FM station because the signal is weak, press

the MPX button to switch the receiver into mono

reception mode. This should improve the sound quality

and allow you to enjoy the broadcast.

Using Neural THX

This feature uses Neural Surround™, THX® technology to

achieve optimal surround sound from FM radio.

• While listening to FM radio, press AUTO/DIRECT for
Neural THX listening.

Press the Menu button. At some point it'll put an 'M' next to the station frequency. Then hit the seek up and down button.

Here is your manual in PDF format:

http://www.bose.co.uk/GB/en/images/Wave%20Radio%20CD_tcm6-4104.pdf

To set AM/PM (12 hour) or Military (24 hour) time - With the system off, hold down Alarm Setup and press On/Off to switch between AM/PM (12 hour) and Military (24 hour) time formats.

To preset up to 6 AM and 6 FM stations - Use the Track/Tune buttons to find the desired station. Then, on the control panel only, hold down any Preset button until the preset number lights. The station is now preset to that number.

Hello george_nutti,

The model number you posted is for a center channel speaker which has no controls, and not knowing the exact model number it's difficult to be specific.

Some Kenwood KDC models allow you to select one of 3 "tuning modes", 1) AUTO1 - Automatic search for stations; 2) AUTO2 - Search Preset stations; 3) MANUAL - Normal manual tuning control. If your Kenwood is one of these models, you need to set the tuning mode to MANUAL. For Kenwood Excelon HD receivers, direct access tuning is done by using the included remote. 1) Press DIRECT button on the remote; 2) Press number buttons to enter desired channel number; 3) Press DIRECT button again to exit direct tuning.

Hope this helps.

Setting Time
1 Press TITLE repeatedly until the time is displayed.
For details, see “Displaying the Text” (page 13)
2 Press and hold TITLE for at least 2 seconds while
the time is displayed.
The time indication will blink.
3 Turn the Rotary encoder to adjust the hours while
the time indication is blinking.
4 When the hour has been adjusted, press MODE.
5 Turn the Rotary encoder to adjust the minutes
while the time indication is blinking.
The time is automatically set 5 seconds after the minute
adjustment. The time can also be manually set by pressing TITLE.
• To synchronize the clock to another clock/watch or radio time
announcement, press and hold MODE for at least 2 seconds after
setting the “hour.” Minutes will reset to “00”. If the display shows
over “30” minutes when you do this, the time will advance one hour.
Listening to Radio
1 Press SOURCE/POWER until a radio frequency
appears on the display.
2 Press BAND repeatedly until the desired radio band
is displayed.
F1 (FM1) F2 (FM2) AM F1 (FM1)
3 Press TUNE to select the tuning mode.
DX SEEK (Distance mode) SEEK (Local mode)
OFF (Manual mode) DX SEEK
• The initial mode is Distance mode.
Distance mode:
Both strong and weak stations will be automatically tuned in
(Automatic Seek Tuning).
Local mode:
Only strong stations will be automatically tuned in (Automatic
Seek Tuning).
Manual mode:
The frequency is manually tuned in steps (Manual tuning).
4 Press or to tune in the desired station.
Holding down or will change the frequency
continuously.
Manual Storing of Station Presets
1 Select the radio band and tune in a desired radio
station you wish to store in the preset memory.
2 Press and hold, for at least 2 seconds, any one of the
preset buttons (1 through 6) into which you wish
to store the station.
The selected station is stored.
The display shows the band, preset number and station
frequency memorized.
•You will need to start from set up or you will not be able to set the mins

i have the exact same problem. i bought a fm transmitter, so i need to tune to a unused fm station in my region wich i cant do because the audi concert tunes up automatic and skips the unused stations ... HELP !

OK HERE'S WHAT YOU DO


1. USING THE UP AND DOWN TUNING, TUNE IN THE STATION

2. PRESS THE MEM SWITCH (LEFT SIDE OF ROUND SWITCH)

3. PRESS STATION LOCATION

4. PRESS MEM AGAIN ---- THAT'S IT

SUMMARY: TUNE, MEM, SET STATION, MEM