Question about Traxxas Rc Revo Nitro Monster Truck

1 Answer

I have a revo 3.3 nitro and im having problems starting it im am indoors about 70 and im flooding the engine i go through the steps for a flooded engine but the easy start won't turn i let it cool down and try it all over again

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I'm new to revos two but i just bought a couple and had the same problem with one of them, make sure your glow plug is ok or just replace it and adjust your high speed needle, i'm in oregon i had to richen mine about 1/4 turn. i also noticed both of the models i got were set differently from the factory. there's info on traxxas website on where the factory needle settings should be.

Posted on May 09, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Traxxas revo 2.5r


the engine shutt down just if load and not bobtail

Dec 29, 2013 | Traxxas Rc Revo Nitro Monster Truck

1 Answer

Troubleshooting


Bad glow plug. Dead battery in ignighter. No fuel going to carb.

May 07, 2013 | Traxxas Rc Revo Nitro Monster Truck

1 Answer

My traxxas revo 3.3's gears are grinding, the car has slowed down


sounds like engine is running to lean. count how many times the high end needle is out. will have to retune engine before piston seizes completly up.

Jul 20, 2010 | Traxxas Rc Revo Nitro Monster Truck

2 Answers

Revo spur gear keeps getting stripped


Youre not setting the right gap between spur gear and clutch bell. all the adjustment is on the engine side so once you got youre spur gear in place loosly fit the engine. Push the engine close to the spur gear so the teeth interlock. Cut a long thin piece of paper and feed it throgh the teeth.turn the clutch bell around. It should feel the same all the way through the turn. If not push the engine closer if it starts feeling loose or ease it away if it starts feeling tight. the paper should come out the other end with a step pattern. the reason for the paper and turning the clutch bell is even though the teeth are intwined at first, once you turn say 3 quaters of a turn if the engine and transmission is not parallel it can move 3 to 5mm in either direction. Lastly use thread lock on all bolts as the vibration can move these and hey presto you are getting another one. Hope this helps.

Jul 07, 2010 | Traxxas Rc Revo Nitro Monster Truck

1 Answer

Traxxas revo 3.3 running problems


Maybe running to lean or to rich. When you accelerate put youre hand where the exhaust is and you should get a light spraying of unburnt fuel over hands(lovely!). If you do you may be able to screw in high end needle in a bit and i mean just a bit. If you hear the engine note raise a bit with a slightly higher pitch then you are running to lean and you will want to unscrew the high end needle valve asap.
Also check youre idle screw and make sure thats not closing the carb and stopping any airflow into engine. Let me know how it goes.

May 30, 2010 | Traxxas Rc Revo Nitro Monster Truck

1 Answer

Revo 3.3...engine doesnt stay on...


Could be a couple of things. Firstly the glow plug may need changing or youre running slightly rich. If you was replacing the glow plug you should retune the engine anyway. When the fuel is entering in the engine where the glow plug is theres either to much fuel and flooding plug out or the plug is not up to the job of burning the fuel. Replace plug and retune. You have had car for two years so guessing you know how to tune the engine.

May 27, 2010 | Traxxas Rc Revo Nitro Monster Truck

1 Answer

My revo wont start it wil just turn over it wont catch i have .23max engine


I believe the problem is your one way bearing. Take off your starting system and remove the bearing, soak it in an alcohol mixture for about an hour, wipe the gunk off and let it dry. Also wipe off your starting shaft. should be good to go.

Feb 16, 2010 | Traxxas Rc Revo Nitro Monster Truck

1 Answer

Revo problems


try checking the auxillary fans if its working, replace it if its not. hope this helps

Jul 03, 2009 | Traxxas Rc Revo Nitro Monster Truck

2 Answers

Traxxas Revo 3.3 shifting problem


you might need to reset the opti drive. turn the power on with the engine still off and hold down the optidrive button for 5 sec. see it that works.

Jun 24, 2009 | Traxxas Rc Revo Nitro Monster Truck

Not finding what you are looking for?
Traxxas Rc Revo Nitro Monster Truck Logo

Related Topics:

289 people viewed this question

Ask a Question

Usually answered in minutes!

Top Traxxas Toys Experts

cwradio73

Level 3 Expert

1162 Answers

kakima

Level 3 Expert

102366 Answers

Mike Darragh

Level 1 Expert

8 Answers

Are you a Traxxas Toy Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...