Question about E-Machines eMachines Monitor E15T4

1 Answer

E machine monitor turns itself off and on

I will hear a click and the monitor will turn off. And then after a little bit, it'll click and turn back on. It doesn't stay on for more than a minute. This just started happening and I don't know where to begin checking for a solution.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

The same thing happened to me today. I was just sitting in my room then i hear a click and the cpu is on it stays on for a while then cuts off. It then cuts on and off with few seconds in between. It then stays in that way cutting and off for about a minite or two and then cuts off completely. A few minutes later it starts again. Also in the time it its off it will not turn on by pressing the power button. Sometimes it completly boots up by itself and then shuts itself down. If I shut it down manually while its on it'll turn itself on immeditaly after. What's going on! Will the warranty cover it? Do I need a new computer?

Posted on Feb 24, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have an emachines E181H TFT LCD monitor and a few months ago it would turn off at random and would come back on.After a few days it stopped turning off by itself I have had no problems till recently,...


After a while LCD monitors develop problems that are usually caused by faults in the internal circuitry. This could be an issue with the power capacitors failing. If you feel confident enough, you can remove the back cover and check to see if any capacitors are bulging or leaking. (Give it at least 24 hours unplugged to allow the capacitors to discharge before doing so). I found THAT little bit of knowledge out the hard way

Jan 22, 2011 | Acer AL2017 20" LCD Monitor

1 Answer

Whirlpool cabrio WTW6700TW1 only fills little bit, won't turn or agitate, buzz sound/humming noise,code F51 flashes??


The F51 error is a RPS (rotary position sensor) board failure where the control board looses contact with the RPS during the machines operation. The RPS uses hall effect sensors to determine the speed and direction of the drive motor, allowing the control board to constantly monitor the motors operation. Because this error is a communication error and not a mechanical error with the motor itself (that would be and F52 error) we can limit our trouble shooting to the three items that make up the RPS circuit, the control board, the wiring harness, and the RPS itself.

Jan 16, 2011 | Whirlpool Cabrio HE 4.5 cu. ft. Washer

1 Answer

Little bit of Water goes in drum does not turn or agitate buzzes and stops working. F 51 flashes?


The F51 error is a RPS (rotary position sensor) board failure where the control board looses contact with the RPS during the machines operation. The RPS uses hall effect sensors to determine the speed and direction of the drive motor, allowing the control board to constantly monitor the motors operation. Because this error is a communication error and not a mechanical error with the motor itself (that would be and F52 error) we can limit our trouble shooting to the three items that make up the RPS circuit, the control board, the wiring harness, and the RPS itself.

Jan 16, 2011 | Whirlpool Cabrio WTW6600SBT Top Load...

1 Answer

The monitor (Gateway FPD1975W) turns itself off after a couple of seconds. I have tried rebooting a number of times - same problem. When I turn the monitor off and then on again it works for a second or...


This sounds like the monitors power supply is failing. (if the monitor is truly right off) Use a flashlight to verify the back-light is not just the culprit. If you can see faint image in the monitor with the flashlight, then this would point tothe LCD inverter is failing. Its most likely the power supply board within the monitor itself. Typically It takes 3 35v 470uf capacitors to fix and a little patience to get apart. Do a bit of googling on "replacing the caps in a FPD1975W" and youll see what i mean. Cheers.

Sep 01, 2010 | Gateway FPD1975W 19" LCD Monitor

1 Answer

Urgent problem with my relisys monitor, please help!


sounds like an overheating problem. you can try blowing out the back of the monitor, or putting a fan close to it. If it is really dirty it will shut itself off so as to not get damaged. is it crt, or lcd?

Apr 15, 2010 | Relisys TL565 15" LCD Monitor

2 Answers

The power switch does not switch (no click)


Unplug the monitor from the power
Unplug the monitor from the computer
Plug the monitor back in.
Try turning it on.

DOES IT SAY "NO SOUCRE DETECTED" or soemthing like that???

if it DOESN'T it means there is something wrong with the computer.

if it DOES:

plug it back on to the computer, turn the computer power off.
Press and hold the power button on the computer for about 15 seconds.
Plug the computer back on.
Try turning the computer on.
if it's not turning on again there a problem either with your monitor cable, or the plug, or the video card plug. It is unlikely that your video card is broken if you hear no wired series of short and long beeps when you try turning the computer on.
Good luck.
Give us updates if you need more assistance

Aug 11, 2009 | Dell UltraSharp 1907FP 19" LCD Monitor

1 Answer

OSD main menu pop-up will not go away


Please try to Turn the monitor off. Hold down the Menu button while the monitor is turned off, then press the Power button again to turn the monitor back on. This should unlock your OSD menu and remove that message from your screen. best regards

May 19, 2009 | HP Pavilion F1703 17" LCD Monitor

1 Answer

Thinkpad g41 2886-78u lcd wont come on


What happend when you plug an external monitor into the VGA connector?

Mar 25, 2008 | Computers & Internet

1 Answer

Thinkpad lcd wont come on


Hello, It may be the power is set wrong. Click start, control panel, power options. From here you can set the amount of time you want the monitor or hard drive/s to remain on until the shut down or go into hibernation. Hope this helps.

Mar 25, 2008 | Computers & Internet

Not finding what you are looking for?
E-Machines eMachines Monitor E15T4 Logo

Related Topics:

221 people viewed this question

Ask a Question

Usually answered in minutes!

Top E-Machines Computers & Internet Experts

Matthew Spark
Matthew Spark

Level 3 Expert

1066 Answers

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18408 Answers

Are you an E-Machines Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...