Question about Reddy Heater-30-55,000 BTU Variable

1 Answer

Motor went bad in a reddy heater pro 110 110,000 btu

I am looking for a motor to replace it can you please help me

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 188 Answers

The manufacturer is online at www.desatech.com . If you go to that website you can find part distributors. I hope this helps you!

Posted on Feb 01, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Master 110,000 btu heater won't start after plugging it in. The tank is full of fuel. Any recommendations .


Hi,


Here are a couple of tips that I wrote that tell you how to troubleshoot a Torpedo or Reddy heater...

Reddy Heater - Troubleshooting Torpedo Heaters





Torpedo Heater Pump Pressure Adjustment


heatman101

][][][][][][][][][][][][][][][][][][][][

Dec 18, 2010 | All-Pro Kerosene Garage Shop Heaters - All...

1 Answer

My reddy heater is 110,000 BTU. It started spitering and sputtering like it was out of kerosene, but still has a half a tank. Any ideas?


If you brought the heater to my shop the absolute first thing I would do is shine a flashlight into the tank. Look for water droplets (or trash) rolling around the bottom of the tank. Keep in mind if there is a "layer" of water the light won't find it. Drain the tank if there is a "hint" of contaminants.

Next, I would check the fuel filter for stoppage or restriction.

Click for more tips

Nov 23, 2010 | Reddy Heater-70,000 BTU Kerosene w/T'stat

1 Answer

Fan starts no ignition then cuts off


Hi,
Here are a couple of tips that I wrote that tell you how to troubleshoot aTorpedo or Reddy heater...

Reddy Heater - Troubleshooting Torpedo Heaters Torpedo Heater Pump Pressure Adjustment
heatman101

..//,/./,

Jun 08, 2010 | Reddy Heater-75-125,000 BTU Variable

1 Answer

My 110,000 reddy heater flames up then after a minute or two just blows cold smoke???


Time for a Full tune-up, plug--fuel filter- 2-air filters -vanes in the pump.

Dec 13, 2009 | Reddy Heater-170,000 BTU Kerosene Deluxe

1 Answer

Glow but no motor or spray


Do you hear and buzzing sound at all?

Jan 30, 2009 | Reddy Heater-30-55,000 BTU Variable

1 Answer

Pro 115 Reddy Heater


The ignitor is bad, there are still parts available from reddyparts.com very simple to install.

Jan 24, 2009 | Reddy HEATER R115 115,000-BTU PORTABLE...

3 Answers

Reddy Heater will not ignite flame


Please answer the following questions. There are several folks on the board that can help but we need to know some vital information so we can get started. Answer these, if you can:
  1. Which Pro 110 do you have. We need the exact model number. Pro 110 is a series of heaters.
  2. Does the heater have a spark plug or a glowbar (HSI)?
  3. When the motor runs is it pumping fuel?
  4. When the motor runs is the spark plug firing (or glowbar glowing)?

Nov 13, 2008 | Reddy Heater-170,000 BTU Kerosene Deluxe

1 Answer

110,000 kerosene heater wont work


All of this model heater use a triac to turn on the motor. The buzzing you hear is because the triac is only turned on half the time due to a component defect on the control.

Replace the control.

or

If you are good with a soldering iron, replace the component labeled "OC2" on the circuit board. This is the optical isolator that caused the triac to "half-wave". Component is a MOC3023

Mar 05, 2008 | Reddy Heater-170,000 BTU Kerosene Deluxe

1 Answer

Ready hater 110,000 btu


replace the nozzle and check the fuel filter - if this is a kerosene heater. under the access plate is a round filter - remove it completely or change it.

Dec 18, 2007 | Reddy Heater-30-55,000 BTU Variable

2 Answers

Reddy heater 110,000 btu forced air portable kerosene


try this, take off the top cover. plug in the heater and when the humming starts, rotate the fan sharply with a screwdriver. keep your fingers away from the fan. if the fan spins under power your start winding is shot. get a new motor. www dot desatech dot com

Dec 06, 2007 | Reddy Heater-30-55,000 BTU Variable

Not finding what you are looking for?
Reddy Heater-30-55,000 BTU Variable Logo

Related Topics:

465 people viewed this question

Ask a Question

Usually answered in minutes!

Top Reddy Heating & Cooling Experts

Mack Baxter

Level 3 Expert

381 Answers

paulcarew

Level 3 Expert

2458 Answers

Richard Marsh
Richard Marsh

Level 1 Expert

7 Answers

Are you a Reddy Heating and Cooling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...