Question about Fisher and Paykel Fisher & Paykel Washer

1 Answer

At spin cycle pump only runs for 3 seconds then stops

Fisher & Paykel top loader 7,5 kg 10 yrs old

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 96 Answers

Sounds like the pump motor is overheating. Probably need a new one.

Posted on Feb 19, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Model gw 712. Why are lights 3, 5, 7, and 8 flashing?


Hotpoint, GE, RCA Washer Repair - Does not spin or drain ...

? 6:13
https://www.youtube.com/watch?v=69az-ZA3eSQ
Jul 10, 2013 - Uploaded by ApplianceVideo.com
Hotpoint, GE, RCA Washer Repair - Does not spin or drain - VWSR4150DAWW ... Fisher & Paykel ... my washer won't drainnor spin. what is the problem? .... But in the end, this video helped me fix our washing machine.

How to repair a Fisher Paykel Washing Machine

www.instructables.com/.../How-to-repair-a-Fisher-Paykel-W...

InstructablesHow do I remove the lid on a F&P intuitive eco washing machine to get to the motor panel?? IMadeIt ... It runs until the spin cycle and it drains but won't spin.

Dec 18, 2015 | Fisher and Paykel Washing Machines

1 Answer

It was on the last cycle spin it stopped had pumped the water out but stopped spinning.


Expert Tips, Troubleshooting & FAQs - Fisher & Paykel ...

https://www.fisherpaykel.com/us/support/expert-tips/Fisher & PaykelFind Tips, Troubleshooting Information, How-tos, FAQs and Answers to Commonly Asked Questions about Fisher & Paykel Appliances.
also on Youtube

Aug 17, 2015 | Fisher and Paykel Washing Machines

1 Answer

Machine will not spin or drain water.


I have a problem with my MW512AU. Sometimes it drains after wash cycle, but sometimes it sticks when it goes to spin, doesn't get up to speed, water comes on for about 10 seconds and shuts off, and it tries to spin again. If I hit the wash progress switch it goes directly to final spin and works ok. I then have to run a 2nd wash cycle to rinse the clothes. I also noticed a buzzing sound when I turn on the power point, which lasts about 3 seconds before stopping. It will come back on every 3-4 minutes for 30 seconds. This is with the machine power switch off. It powers on normally.

Mar 13, 2010 | Fisher and Paykel GWL11 Top Load Washer

2 Answers

Water not coming with force in Fisher & Paykel SmartDrive Top-loa


Try taking the cold hose of at the tap and check to see if has a little mesh filter in there. This could be blocked up with gunk.

Jan 12, 2010 | Fisher and Paykel GWL11 Top Load Washer

1 Answer

Fisher Paykel Gw11, leaking, loud noise, not going through cycle


pump is a common fault and easy to change for about $25. all sound related. new machines are pretty inexpensive. your call

Aug 23, 2009 | Fisher and Paykel GWL11 Top Load Washer

2 Answers

Stuck on spin


Hi. this is a failed timer device. simply replacing the timer control module will eliminate these issues you are having.

thank u
rate me!!

Jul 27, 2009 | Fisher and Paykel GWL11 Top Load Washer

2 Answers

On our Fisher and Paykel, the spin cycle does not


ok guest you can set a fisher and paykel machine to skip one rince cycle so as to save water,

Feb 20, 2009 | Fisher and Paykel GWL11 Top Load Washer

6 Answers

Fisher and paykel 7.5 smartdrive washing machine, no power


If there is power and all your lights are lighting up but you get no responce from the machiene eg no spin, water filling, wash cycle or drain then it will be the sensor for the lid it will have coroded but this is an easy fix , I hope this helps

Feb 20, 2009 | Fisher Paykel Eco IWL16

1 Answer

Fisher & Paykel Smart Drive 9 Pride


Check your exit hose spigot, it may be clogged. This is if your filter is all clean. There should be air for passage in the standpipe behind. Your hose should not fit airtight into the standpipe and neither too deep into it (4 to 6 inches maximum). Snaking out your standpipe would be good too.

Rate me pl.....if helped. Click on 'thanks for trying' if not helped, your prob will be back for someone else to solve.

Dec 10, 2007 | Fisher and Paykel IWL12 Top Load Washer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

209 people viewed this question

Ask a Question

Usually answered in minutes!

Top Fisher and Paykel Washing Machines Experts

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Are you a Fisher and Paykel Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...