Question about Sony Televison & Video

1 Answer

Hi. My Sony Videoscope XBR's Convergence Allignment

Hi. My Sony Videoscope XBR's red convergence is out of whack or something, I really don't know what it wrong that is why I am posting. Either the red convergence on the tv is unalligned with the green and blue right away when I start the tv, OR, the convergence randomly will un-align with the other two in the middle of watching something while the tv has been on for a bit. Either way the convergence eventually is un-aligned. Sometimes the convergence will realign itself eventually or we have to turn the tv for a while. The red convergence will only unalign ABOVE or BELOW the green and blue. Most of the time when it is above you can fix it immediately with the convergence settings. Here is the kicker: When the red convergence usually unalligns it is usually BELOW the blue and green and is unfixable unless the tv is turned off for a while or we wait a while.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I happen to share this same problem. The alignment of the gridlines on the standard convergence panel are completely abnormal, and if I attempt to auto-adjust the TV, it flashes different colors on the sides of the screen , and then turns off the convergence settings.

Posted on Mar 24, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Manual for Sony videoscope XBR, model # KP-53xbr35


Hi csp,
Welcome to FixYa.
My name is John.
I will be assisting you with your issue.
You can get one here. www.manualsonline.com .
Thanks for choosing FixYa.
John

Jan 03, 2011 | Televison & Video

1 Answer

Distorted curved picture upper and lower screen on my Sony Videoscope XBR model kp53xbr35


CONVERGENCE PROBLEMS ARE COMMON ON THIS MODEL. THIS WILL REQUIRE PARTS REPLACEMENT.

Dec 27, 2009 | Televison & Video

1 Answer

Hitachi convergence issues


Hi,,,

This is a convergence issue

Try to visit this site

http://home.earthlink.net/~oleg.filippov/ConvergenceFix.htm

Regards
PCmania

Jul 08, 2009 | Hitachi 60EX38B TV

1 Answer

Sony videoscope XBR - Side by Side screens can't change it back.


Sounds like your TV has a PIP (picture in picture) that allows your AVI (audio visual input) to be viewed simultaneously with your cable input. Check the manual for the correct buttons, but the one you're looking for says either PIP or AVI or something along those lines. Hope this helps

Jun 11, 2009 | Mag Innovision InnoVision XJ 717 Monitor

1 Answer

Sony 51 inch Projection TV.


Dear AJ,

To be very Honest, i am not well conversant with Rear Projection TVs.

I suggest that you try with someone else.
Again from my personal point of view, i am of the feeling that itcan be fixed, and pretty easily. There must be a "Service Mode" which can be accessed by the remove, and then the Convergence Settings / Adjustments can be corrected.

But, I shall make additional enquiries and and let you know.

Cheers

Pravin

Dec 01, 2008 | Televison & Video

1 Answer

Sony Videoscope XBR 53


This is a convergence problem. Look in the back for a couple of large black ICs attached to a heatsnik. These should be marked STKxxx. These are the convergence ICs and either have bad connections or are defective. If you can solder, try resoldering the pins on these ICs. If that fails to resolve the problem, replace the ICs. There may be other parts that need to be replaced as well. I'll look up your model to find the other parts to check. The convergence board as an assembly, I believe, is no longer available. The parts that you require are available.

Dan

Sep 18, 2008 | Televison & Video

3 Answers

Sony Videoscope XBR tv


This is usually a convergence problem.. Could you update this with the model number please. That will allow me to give you some specifics about what could be wrong and how to fix it.
Dan

Apr 18, 2008 | Mag Innovision InnoVision XJ 717 Monitor

1 Answer

Sony Videoscope XBR TV


just need to balance the three colors red,green and blue that may help remove the front covers and look for black module that have sccree and focus controls just move a little bet left or right be carefull because you can loos the picture e-mail me for more info

Apr 07, 2008 | Sony KP-53XBR45 53" Rear Projection...

1 Answer

Convergence code


need to replace convergence amps and possible fuse

Oct 05, 2007 | Sony KP-57WS500 57" Rear Projection...

Not finding what you are looking for?
Televison & Video Logo

Related Topics:

456 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sony Televison & Video Experts

kakima

Level 3 Expert

102366 Answers

The Knight
The Knight

Level 3 Expert

74383 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Are you a Sony Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...