Question about Nintendo Wii Console

1 Answer

My we controller only works from far away how can i adjust it to work closer

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 60 Answers

You need to resync your wiimote. To do this remove the batteries and then reinsert them and press the red button on the wiimote and on the wii. Also try placing your sensor bar in different places for comfort.

Posted on Feb 01, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Technician can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Technician (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do I adjust the position of the sliding doors on my quadrant corner unit shower or how do I remove the doors to clean behind? thanks

Look at the top and bottom mounting points for indications that it may be adjustable. It may be necessary to remove the door to expose the adjustment provision.

Aug 22, 2015 | Home

1 Answer

What if I am only getting some keys to work

bluetooth signal is tricky, like any wireless signal can be interrupted. try relocating receiver and transmitter closer together and away/ as far from metal objects/panels. check keyboard lock for numbers etc...

Aug 14, 2014 | GE Bluetooth Wireless Keyboard 98618

1 Answer

Netgear wn2000 states mover closer to router?

This message means your extender is too far away from your wireless router to make a good connection. Repeaters must be within a good signal range for the connection to work properly.

If you have a wifi enabled phone, tablet, or laptop, you can walk around your home and see where the signal reaches and how well. Repeaters should be placed where you still receive full or close to full signal.

Repeaters may have issues if the wireless router is on another floor, behind metal, or too far away.

Jul 04, 2014 | NetGear WN2000RPT Repeater

1 Answer


51330 code error means that your router is too far away from your wii...move your router closer to your wii console or vice versa....and then turn off your modem for about 3-5mins. and turn it on again and try if it works...

Dec 06, 2011 | Nintendo Wii Console

1 Answer

I lost my arrow what can I do thank you

Hi there,

First, check to make sure the lights on your remote are still on. One thing that will help is to replace the batteries. Also, get closer to the sensor bar until you see the arrow. At that point, you can go into the Wii Settings and adjust the sensitivity. Adjust it until you can be far enough away to see the cursor.

Jan 24, 2011 | Nintendo Wii Console

1 Answer

I have a '95 chevroelet pickup and I need to replace the brake light switch by the brake pedal. Any advice or instruction

It is Fairly Simple and Self Explanitory, Install and Adjustment is as Fallows.
The Closer to Pedal arm the Button is the LATER the Brake lights will Illuminate, so you want it as Far away as Possible you need an assistant to Watch for you.

Aug 24, 2009 | 1994 Chevrolet C1500

2 Answers

Brake lights will not turn off after brake light switch replaced.

There May be a RETURN Spring for the Padal, other than that The Switch MUST Be out of ADJUSTMENT Try Adjusting it the Other Direction its My Experience that the Further Away from pedal the Closer to ON the Switch is
On your Vehicle it May Be Different though But TRY IT Hope it Fixes the Problem

Jun 07, 2009 | 1989 Plymouth Reliant

1 Answer

Carolina rudder does not work properly

Slider to which the pegs are attached is probably binding, take entire mechanism out (2 screws), and lubricate with silicone wax. If that doesn't work, replace sliders and pegs.

Apr 06, 2009 | Carolina Manufacturing Perception Carolina...

Not finding what you are looking for?
Nintendo Wii Console Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nintendo Video Game Consoles & Games Experts

Bee Santiago

Level 2 Expert

268 Answers

Raj Patel

Level 3 Expert

917 Answers

Julian Wainwright

Level 2 Expert

64 Answers

Are you a Nintendo Video Game Console and Game Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides