Question about Welding Tools

1 Answer

Hi just bought a aga 400 mig welder could any one help with the various settings on it, Do the amps adjust with wire feed ? Thaks dave

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 92 Answers

Yes

Posted on Feb 02, 2010

Testimonial: "Thanks Ken all is comming clear now"

  • Ron Jones
    Ron Jones Feb 02, 2010

    Dave, The WFS alters with the amps, the voltage needs to be adjusted as you alter the WFS. dose this satisfy the question or do you require further info.

    Ken

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My SIP ideal 240v mig welder keeps tripping garage and/or house power, what's wrong?


welder drawing high current.sounds like a earth problem with the house or the unit.

Aug 14, 2014 | Welding Tools

1 Answer

Require schematic for canox c-sw350 welder


Since most operate on the same basic principles, the motor control should use a simple pair of SCR's to drive the wire feed and speed. They are often a weak point as most are just 200 volt 8 amp standard sensitivity types. A standard Gate 400 volt 10 amp type gives a margin of reliability without costing much more, and sometimes less.

Various vendors sell them,

Dec 16, 2011 | Welding Tools

1 Answer

Kende 150R gas/nogas mig welder


Hi I have the same welder with the same problem, I've striped it down and found that there are a few teeth missing on the gears that run the wire feed,
Had no luck finding any replacement parts though

Sep 05, 2010 | Troy MIG100 90-Amp. Wire Feed Welder

1 Answer

I have a firepower fp130 mig welder . I have been using 0.30 wire,can I use bigger wire in it,if so how do I adjust the welder for it


The only thing you need to do is change the tip to the 0.30, and feed the wire. If no 0.30 tip is included with the welder it just isn't designed for that wire. You will also need to flip your friction feed wheel at the box to match the diameter.

Mar 24, 2010 | Firepower 120 Amp MIG/FLUX Cored Welding...

1 Answer

The Mars 180 MIG Welder Manual neglects to


Hi mate. Not sure on the power settings but the earth clamp is negative for gasless and possitive when useing gas

Mar 20, 2010 | Welding Tools

1 Answer

Owners manual for a century wire feed 83160 mig welder


I believe century was bought by lincoln. call 1-866-236-0044 ext 3. Ask for century parts.
Paul

Apr 19, 2009 | Lincoln Electric LE 83180 Century...

2 Answers

I have a Campbell Hausfeld MIG Welder 80, The wire will not feed,


Here's a link to the Campbell Hausfeld web page. Look under "Service Center" for "Find a Part." I hope this has what you need.

http://www.chpower.com/webapp/wcs/stores/servlet/chHome_10051_10001_-1

Feb 22, 2009 | Campbell Hausfeld RBWG202000 NA 70 Amp....

1 Answer

Wire feeds too quickly


Some welders control wire speed with the amps control, some control amps with the wire speed control. You might try turning things up until it runs smoothly without pushing back. If you're new at welding, it does take some practice until it feels right.

Jan 15, 2009 | Hobart Handler 140 Mig Welder

1 Answer

Mig welder tripping power supply


the breaker could be bad. try to change the breaker

Dec 09, 2008 | Troy MIG100 90-Amp. Wire Feed Welder

Not finding what you are looking for?
Welding Tools Logo

Related Topics:

156 people viewed this question

Ask a Question

Usually answered in minutes!

Top Welding Tools Experts

Brad Brown

Level 3 Expert

15557 Answers

yadayada
yadayada

Level 3 Expert

75822 Answers

Bill Boyd

Level 3 Expert

42218 Answers

Are you a Welding Tool Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...