Question about Yamaha HTR-5140 Receiver

1 Answer

I have a HTR-5140 stereo receiver 6 years old used very little. Last time I turned it on after two seconds I heard a click and it turns itself off. No fuses that I know of accesible from the outside?? Any ideas Thanks

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

There should be schematics or a Manuel in pdf form online that should tell you where the fuses are.

Posted on Feb 01, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Technician can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Technician (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Heard a "pop" and my


Maybe. Clearly something blew up. Diagnostic time costs money. Then there are parts and labor.

You can get a new one on ebay ending tomorrow for as little as $140 delivered.

http://cgi.ebay.com/Denon-AVR-2105-stereo-receiver-/220774248046?pt=Receivers_Tuners&hash=item33672bae6e

Apr 25, 2011 | Denon AVR-2105 Receiver

Tip

Reset factory default settings for yamaha HTR-5650 AV receiver


How to reset yamaha HTR-5650 AV receiver (maybe others) to factory default settings:

1. turn power off.
2. press the 6ch input and stereo button simultaneously for 4 seconds. Then while holding down these 2 buttons, turn the power on.
3. press preset tuning to the right until option #9 is selected.
4. Then, press program button until the *RV option is selected.
5. turn power off, wait 10 seconds.
6. turn power on, settings are reset.

on Feb 10, 2009 | Yamaha HTR-5650 Receiver

3 Answers

How do I reset my yamaha receiver htr5730


http://www.retrevo.com/support/Yamaha-HTR-5730-Receivers-manual/id/1075bh230/t/2/

Page 52

1 Hold down STEREO on the Front Panel
"Factory Preset" appears on the front panel
2 Press STEREO to select the desired setting.
'Reset' To reset to factory presets
'Cancel' to cancel without making changes
3 Press STANDBY/ON to confirm your selection

Jan 15, 2011 | Yamaha HTR-5730 Receiver

1 Answer

My receiver won't turn on. All I get is a fast


I am sure you have tried and disconnecting all the speakers and taking the unit to another outlet right? If it works you fried your surge and need to replace it. Otherwise the unit went into that strange power protection mode

Jul 05, 2010 | Yamaha HTR-5790 Receiver

1 Answer

I turn it on and within seconds it shuts itself off. what is up with this? model number htr 5790. it has been working flawlessless until today. nothing touched or changed.


Shutting off before the safety relay clicks means there is a problem with one or more audio output channels. Time to see a service center. There is little that can be done without a tech...

Mar 30, 2010 | Yamaha Audio Players & Recorders

1 Answer

Our HTR-5660 is about 5 years old. Recently it


I solved the problem by ensuring the Impedence selector was either all the way to the left or all the way to the right, as instructed in the manual.

Jan 19, 2010 | Yamaha HTR-5660 Receiver

1 Answer

NAD 7140


The clicking is the sound of a bad relay. A relay is an electrical switch that opens and closes under the control of another electrical circuit. There is no user solution for this. You'll have to take it to an electronics repair shop (~$150) or dump the whole unit.

Nov 22, 2008 | NAD 712

1 Answer

Sony STR-DE135: No audio output


first, at turn on you should hear a relay click then a few seconds later a second click. if you should hear the two relay clicks then check to see if you have both A and B speakers on, if you do shut B speaker off. next check the tape monitor switch make sure that it is off. if you should not hear the second relay click you have a problem with the unit and needs to be repaired.

Feb 17, 2008 | Sony STR-DE135 Receiver

3 Answers

Yamaha HTR-5990 Audio no longer works


MichaelM
Did you ever get this resolved?  I have a similar problem, my video feed seems to work but I have never been able to get any sound from my speakers using this component.  I'm not sure what YPAO setup is but I just read a suggestion to reset the receiver to factory settings in the event something is programmed that causes the problem.

Jun 21, 2007 | Yamaha HTR-5990 Receiver

2 Answers

Yamaha HTR-5990 Receiver


I JUST EXPERIENCED THE SAME SITUATION HERE IS THE SOULTION YAMAHA SENT ME TO RESET THE SYSTEM HTR-5990 YAMAHA HTR-5990 FACTORY PRESET PROCEDURES All models require the STANDBY/ON button to be turned OFF to start the reset process. NOTE: The remote control cannot be used during the reset procedure. All necessary buttons to complete the reset process are located on the front panel of the receiver. This procedure is not intended to correct intermittent shut-off symptoms or problems MODEL: HTR-5990 (U.S.A. model/s) (BEFORE YOU CONTINUE, PLEASE READ THE ABOVE NOTES!) 1. Before you start this procedure, locate the MASTER ON/OFF button and the STRAIGHT/EFFECT button on the Front Panel of the unit. 2. MAKE SURE THAT YOUR RECEIVER’S MASTER ON/OFF HAS BEEN TURNED OFF. 3. With the Right Hand, press and hold the STRAIGHT/EFFECT button. With the Left Hand, press the MASTER ON/OFF button and HOLD both buttons for no more than “3” SECONDS, AT THE SAME TIME. SP IMP. * 8 MIN. will appear on the display, which indicates you are in the Diagnostics Mode. 4. Rotate the PROGRAM KNOB to the right (ONCE) until the display reads PRESET *CANCEL. 5. Press the STRAIGHT/EFFECT button (ONCE) and the display will change to PRESET RESET. 6. Turn the unit off by pressing the MASTER ON/OFF button. 7. Wait 5 seconds, then turn the unit on by pressing the MASTER ON/OFF button. You have now reset your component to the factory settings. NOTE: Yamaha receivers don’t have to be reset during normal operation. It is not recommended that you reset the receiver unless a setting has been changed that you are not aware of, or the receiver is not operating properly. The reset procedure will clear an incorrect setting that might be causing abnormal operation. GOOD LUCK

May 01, 2007 | Yamaha HTR-5990 Receiver

Not finding what you are looking for?
Yamaha HTR-5140 Receiver Logo

Related Topics:

176 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Audio Players & Recorders Experts

 Grubhead
Grubhead

Level 3 Expert

5309 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

The Knight
The Knight

Level 3 Expert

74887 Answers

Are you a Yamaha Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...