Question about Check Point Network Adapter

3 Answers

My husband locked both keys in the safe 94985...

My husband locked both keys in the Bunker Hill safe 94985... The 159# does not open-- I never put in a pin

Posted by on

  • Anonymous Mar 23, 2014

    model 94985

×

Ad

3 Answers

  • Level 1:

    An expert who has achieved level 1.

    Teacher:

    An expert who has written 2 tips or uploaded 1 video tip.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Search on "How to open a safe with a potato" and you'll find a youtube video on how to open that safe. All the Bunker Hill safes use the same lock mechanisms which have a critical design flaw if the spring on the solenoid is weak in that the plunger bounces enough to allow the bolt to be thrown open if you can time hitting the front of the safe just right. Of course, if you mount it such that you can't get a good swing in then no problem. There are two adjustment screws to the bolt throw, if your safe is easily opened this way, you might want to adjust these screws so that more of the plunger hits the stop. I couldn't get mine to open with a rubber mallet but it's mounted so you can't get a good swing in.

Posted on May 13, 2010

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 66 Answers

It sounds like a job for a professional locksmith.

Posted on Jan 30, 2010

Ad
  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 1 Answer

Take Bunker Hill 1.5 cubic foot safe to a concrete floor. Lean safe back 6 inches or so and let it flop back onto floor while turning the knob. The impact on floor drops pin out of way and allows knob to turn. Install a washer or two behind the lever on the back of the key and reinstall lever, lock washer and nut with Loctite and tighten. The washers move the lever farther aft enabling better contact with the washer that pushes the pin down. This nut was loose causing our problem. FNH

Posted on Nov 25, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Technician can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Technician (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The safe is a Bunker Hill Digital Floor Safe with the following number JH0525710Item 45891 SKU P45991 I lost the code several years ago and don't have a key. How do I open the safe?


In the absence of a code and a key you can't. If it were easy to get into a locked safe, there would be no point. They exist to stop exactly what you are trying to do.

It appears to be a Harbour Freight brand, so you will get no help there.

http://www.ehow.com/how_6546958_open-hill-digital-floor-safe.html

This shows it is Harbour Freight and specifically says they don't supply replacement keys.

Owner's Manual & Safety Instructions

pdfstream.manualsonline.com/9/9e66a90a-2061-4a6f-be5c-10125e503262.pdf

Visit our website at: http://www.harborfreight.com ... To ensure security of your safe, Bunker Hill Security ... Only use this Safe on a stable, level, clean and dry.

Get a locksmith to drill the door off and get rid of it.

Feb 02, 2017 | The Computers & Internet

1 Answer

How can I open my Bunker hill safe 95824 with a battery failure ?


Call harbor freight in CA and they'll let you know if there is a cure. They have an 8xx number for ordering parts and such, which is also their 'tech support' line.

Aug 15, 2014 | Computers & Internet

1 Answer

I have a bunker hill safe ,item# 91006,batteries too low,no key, drilled out overide lock,still won"t open, now what?


you can also get some wires feed him into the back contacting the battery terminals hold in there with a 9 Volt, four hands and patieance and then..... you get my drift. Worked for me! :) $

Dec 26, 2012 | Computers & Internet

2 Answers

I own a Bunker Hill digital floor safe sku #need code change data


To change the code: Your safe comes
preset with the default code of “159-A”.
To change the code, first open the safe.
On the inside of the door near the hinge,
there is a small red “reset” button. Press
this button until the Yellow LED on the
front panel lights up. Now, input your new
code up to 8 characters, followed by
either “A” or “B”. The Yellow LED will flash
to indicate that your new code has been
accepted. Warning: If the Yellow LED
does not flash, the code has not been
accepted, and you must start over.
NOTE: Be sure to test your new
combination before closing the door.
NOTE: Be sure to have the Override Key
available when setting a new
combination or changing batteries, in
case the door doesn’t open.

Good Luck

Nov 15, 2009 | Sentry Fireproof Safe

1 Answer

Bunker hill safe model no.45891 bought used, can't open. any ideas?


Safe has Key lock hidden on it? Contact Harbor Freight with serial number, to try and get new key. Once opened follow these instructions at:

http://www.harborfreight.com/manuals/93000-93999/93575.pdf

Oct 20, 2009 | Check Point Network Adapter

2 Answers

CANT UNLOCK BUNKER HILL BOOK SAFE


Battery died and i can't find the key or the instructions to open the safe

Sep 22, 2009 | Locks & Locksmithing

2 Answers

I have a bunker hill safe digital, and battery is too low to open the safe and cant find my key, probably inside, any suggestions


If you have the small electronic Bunker Hill safe with lost keys and dead batteries, this is a potential solution... Take a hammer and strike the top of the safe while attempting to open at the same time. You may need to place on object on top of the safe such as a flip flop shoe to strike with hammer to smooth out the pressure when striking. It should pop open after several attempts.

Jan 25, 2009 | Check Point Network Adapter

6 Answers

Cannot get my Bunker Hill Safe open.


get the key number that is listed above the key hole and then call 888-299-3427 for a replacement

Nov 21, 2008 | Check Point Network Adapter

7 Answers

Bunker hill safe


i had the same problem this is what i did. i took the lil leg off the bottem it held on by a srew take a cloths hanger put it in the hole and now u can hit the lil button that is for makin a new code it is on the hing side of the door the yellow light will come on and stay on now put ur new code in then hit a or b i used 1111a then changed it once i got in o by the way ''the factory code is 159a try this first" and the cloths hanger i shoved a ear plug on the end of it so that way it could grip the button hope this helps somebody

Sep 20, 2008 | Check Point Network Adapter

Not finding what you are looking for?
Check Point Network Adapter Logo

3,202 people viewed this question

Ask a Question

Usually answered in minutes!

Top Check Point Computers & Internet Experts

DROPNDEAL
DROPNDEAL

Level 3 Expert

2585 Answers

Laxman Bisht
Laxman Bisht

Level 3 Expert

662 Answers

Gil Shultz

Level 3 Expert

3368 Answers

Are you a Check Point Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...