Question about Miller SYNCROWAVE 250 DX TIG RUNNER WELDER 951117

1 Answer

I have a Miller Dynasty DX welder that shows a code of HEL P-7, need to know what code is and can it be reset or repaired

Posted by on

  • 1 more comment 
  • noneck09 Jan 31, 2010

    The Serial No KJ036758 thansk

  • noneck09 Feb 02, 2010

    Miller Dynasty DX Serial #KJ036758
    Stock #903519-01-1

  • noneck09 Feb 03, 2010

    I am sure but will check

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,030 Answers

I need your serial number to get correct info...please reply here

Posted on Jan 30, 2010

  • Sean Wright
    Sean Wright Feb 02, 2010

    Are you sure its a code HEL P-7?? Could it be HEL-P1 ?

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hel -10 on max star 200


The Help 10 code on a Miller Maxstar 200 indicates a depressed trigger. If it still doesn't clear, replace the trigger control.

Jul 29, 2014 | Miller Welding Tools

1 Answer

Have a Miller Dynasty 300 that won't tig weld, displays HELP 12 code. Suggestions??


Some welders have a resistor that is obvious and accessible but to give an error code it is likely something else inside. You'll have to look at the circuit board for a component that is burned. If you are lucky you will find a fuse.

Nov 21, 2013 | Miller SYNCROWAVE 250 DX TIG RUNNER WELDER...

1 Answer

Plugged in Miller Dynasty 350 and it said REL RMT. Wouldn't let me change the settings, all I could do is turn it on and off. I checked the owners manual inside and out and couldn't find...


Hi:
Legend REL RMT means release remote, this happens when your torch's trigger is depressed and you need to release the trigger to continue.
Check the owner's manual on section 7-4 troubleshooting, it's there.

Sep 08, 2011 | Miller DYNASTY 350 TIG WELDER w/TIG TORCH...

1 Answer

Help code 24 ?


On this page enter your serial number and you will be able to download your manualhttp://www.millerwelds.com/service/ownersmanuals.php In the Dynasty 350 manual On Page 76, section 7-4 it says: Help 24 Display Indicates a power supply to the control and interface board PC6 failure. Possible cause is a short in Pin A or Pin B of the remote control. Unplug the remote control and see if it goes away.

Dec 05, 2010 | Miller DYNASTY 350 TIG WELDER w/TIG TORCH...

1 Answer

Miller dynasty dx 300 that began throwing help code 7, which is too high of voltage. The voltage reads 246 volts coming in to the welder. It keeps blowing diode pack pm2. Any ideas what could be the...


The Voltage refered to is the Arc Voltage not the input voltage, for dip transfer the arc voltage needs to be 18-20v for spray transfer try 25-38volts both depending an the WFS setting. arc voltage is set on the voltage control dial. lets know how this turns out.#
Ken

Feb 01, 2010 | Welding Tools

1 Answer

Changing from 480v 3 phase to 220v single phase need diagram on a Miller Dynasty DX tig welder Serial # KH577649 stock 903519-01-1


i have a old miller thunderbolt CC*AC/DC welder its wire single phase 480 can it be switched to 220 single phase

Dec 02, 2009 | Miller Welding Tools

1 Answer

Need wire diagram for Miller Syncrowave 250 DX


diagram is on the inside of cover or go to Millerwelds.com

Jun 21, 2009 | Miller SYNCROWAVE 250 DX TIG RUNNER WELDER...

1 Answer

Overcurrent condition in primary IGBT switching circut


This is a very difficult machine to diagnose even for a factory trained person,do not reccomend.

Apr 24, 2009 | Welding Tools

1 Answer

I have a miller dynasty inverter tig welder   It has a help code that comes on when I turn it on the code is p-2


From the user manual for a generic dynasty model welder:
2 Help 2 Display
Indicates an open in the thermal protection
circuitry located on the left side of the unit.
Contact a Factory Authorized Service
Agent if this display is shown.

So you could have anything from a broken or disconnected wire to a bad thermal switch.

You can get user manuals specific to your welder at www.millerwelds.com

Rank this answer please,
Carl

Nov 26, 2008 | Miller DYNASTY 350 TIG WELDER w/TIG TORCH...

Not finding what you are looking for?
Miller SYNCROWAVE 250 DX TIG RUNNER WELDER 951117 Logo

472 people viewed this question

Ask a Question

Usually answered in minutes!

Top Miller Welding Tools Experts

John Trevino

Level 3 Expert

1383 Answers

wadingriver
wadingriver

Level 3 Expert

2069 Answers

Jose Velazquez
Jose Velazquez

Level 2 Expert

227 Answers

Are you a Miller Welding Tool Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...