Question about Projection Televisions

1 Answer

QUASARS INQUERITIES WELL THE TV WAS ON SHUT IT OFF WONT COME BACK ON IS THERE A RESET BUTTON ON IT

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 211 Answers

Sorry to report there is no reset on your set. I am suspect that you may have a bad capacitor in your power supply board. I'de strongly suggest you seek professional help on the repair of your set. I hope in some way this has helped.
Have a great Presidents Day.
Ed
NC Electronics
Mills, Wyoming

Posted on Feb 18, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My tv shut off while watching and won't come backon


Fault at its main digital board. Short circuited component/s at it. Contact any service technician; or the authorized service center. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts.
http://electronicshelponline.blogspot.com/
In most cases, the main board might have to be replaced. If so, a software [firmware] update too might be necessary.
Before going further; try a hard reset first. If it does not help you, replace the main digital board. There are two methods to reset TVs. The first is simple to do; a Hard Reset. The other is somewhat skilled; is a Factory Reset (System Reset). To make it a hard reset, just unplug the TV from AC mains wall socket, and re-plug it back after 15 minutes or so. If you do this by overnight is better. This procedure will make it a hard reset. If you want to make it a system reset [Factory Reset]; you have to enter its service mode option, and select the factory reset option. If you wish to get some details; visit the site linked here.

Aug 08, 2016 | Projection Televisions

1 Answer

Tv shuts off, when turned back on, the green light keeps blinking and tv wont come back on. if you leave off for a few min. the tv will come back on. then the tv will shut off again after a few min.


One of two things...first hold power button while you hold the up button on your remote, this will reset your tv to manufacturer's settings....you could have sleep timer on.....if this does not work, you have to replace the lamp, my tv did the same thing and it happened to be the lamp. Hope this helps, good luck

Aug 05, 2012 | Sony Grand WEGA KDF55E2000 55" Projection...

1 Answer

TV WONT START UP - RED LIGHT COMES ON AND THERE IS A CLICKING NOISE AS IF IT IS TRYING TO RE START - IS IT THE LAMP UNIT OR STARTER?


if the lamp has gone the bottom light will flash if the top flashes there a problem with the tv there is reset you can do
  • Point the Sony remote control at the TV and press and hold the "Up" arrow button.

  • 3

    Push the "Power" button on the TV while holding down onto the "Up" button. Release the "Up" button when the TV turns off, then turns back on.

  • 4

    Select "OK" when shown the factor settings and the television has completed its TV reset



  • Read more: How to Completely Reset a Sony TV with a Blinking LED ' eHow.co.uk http://www.ehow.co.uk/how_6011902_completely-sony-tv-blinking-led.html#ixzz17Eijjdrn good luck regards shaun

    Dec 05, 2010 | Sony Grand WEGA KF42WE610 42" Rear...

    1 Answer

    I have a Panasonic pt-52lcx65-k. I thought the lamp was gone so i replaced it. Now the tv wont come on at all. Just a orange light flashing. I tried to reset it by holding the volume button and the pip...


    Howdy,
    Doble check your Lamp Installation, making sure that the Lamp Cover is properly secured. Reset TV by unplugging TV from the wall for 3-4 minutes then plug back in, then turn TV on.

    To reset your Panasonic Lamp Time:
    ø Press and hold these buttons for (at least) 5 seconds:
    ø Volume Down button (on TV Panel).
    ø AND ACTION Button (on remote).

    As the remote gets older the ACTION button may not respond unless you press the button dead center and not at an angle.

    Thanks for using FIXYA, BIG IRISH.

    Dec 19, 2009 | Panasonic PT-52LCX65 44" HDTV

    1 Answer

    Lamp light flashing tv wont come on


    No reset of lamp hour is required. If lamp is original form Hitachi then check Lamp Cover, it might not put back or not seated well.

    Jan 01, 2009 | Hitachi 60V500 60" Rear Projection...

    2 Answers

    Hitachi 50dx10b


    Try unplugging and plugging back up the power cord to reset it.

    May 14, 2008 | Hitachi 50DX20B 50" Rear Projection...

    1 Answer

    Samsung TV


    If your model has a reset button it will alway be on the back,
    usually near the power, sometimes near the lamp if it is dlp.
    plainly marked.
    Or just unplug it , press power on . then plug it back in.

    Jan 27, 2008 | Projection Televisions

    1 Answer

    Flashing green button, won't reset or turn on


    http://www.chrisandnat.com/Projects/BlinkingTV/blink.htm
    http://www.jeremyburns.com/Mitsubishi-Green-Blinking-Light-Fix.pdf

    Dec 18, 2007 | Mitsubishi WS-65513 65" Rear Projection...

    2 Answers

    56DR650 Wont Turn on


    I have a problem occasionally because the color wheel won't start. It has a bearing problem and is very noisy.

    Nov 20, 2007 | Sharp 56DR650 56" Rear Projection HDTV

    Not finding what you are looking for?
    Projection Televisions Logo

    Related Topics:

    38 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Projection Televisions Experts

    Jaime Hernandez

    Level 3 Expert

    2267 Answers

    matt martin
    matt martin

    Level 3 Expert

    1191 Answers

    yadayada
    yadayada

    Level 3 Expert

    60792 Answers

    Are you a Projection Television Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...