Question about RCA RT2250 System

1 Answer

Rca rt2250 no sound

I just want to use the receiver, I have no other components hooked up, I have two speakers hooked up, but get no sounds at all.

Posted by on

  • no noise Feb 17, 2008

    i have a rca rt2250 audio video receiver. i would like to just beable to use the fm receiver. i have only two speaker hooded up and have the am and fm antennas hooked up properly.i have power and the unit when turned on says tuner and i tune it to a radio station i still get no sound



1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert who has answered 20 questions.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 107 Answers

Please give us more details, I don't know what reciever you want to use? AM,FM? or some other devices.
but if it's the am,fm reciever well you can find it in your instructions manual how to set it though.
just follow the steps and you will have it..

have a nice tunning
just don't rate me badly^^

make sure your antenna is connected properly..

Posted on Feb 17, 2008

  • Mark Payas
    Mark Payas Feb 17, 2008

    but you can use the aux for video and audio?

    when you turn the tunning dial, will it change?

    have you tried to press the autoscan for fm? maybe it can't scan any frequencies.

    well if you did this all, the audio driver through frequency reciever is broken. needs to be repair by a proffesional technician.

    this is a IC (integrated circuit) in which drives the audio signal to the amplifier section.



1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

RCA 5.1 Surround Sound Receiver Sounds fade in and out

chk how you are hooking up the speaker polarity minus to minus and plus to plus.

Oct 17, 2009 | RCA RT2250 System

1 Answer

I have a DVD player, VCR player, TV all attached to an RCA RT2250 audio/video receiver. All was just fine until 2 days ago when the DVD player would no longer give sound and icons of the speaker system...

It's possibly only needs soldering of the voltage regulators. they are on the main circuit board heat sink (middle of the receiver and can be accessed by the bottom panel.


Dec 21, 2008 | RCA RT2250 System

1 Answer

Hooking up speakers

I'm sure you hooked it up the correct way,This rt2250 is a problem to almost everyone.I have two of them and they both present all types of faults

Jul 27, 2008 | RCA RT2250 System

1 Answer


You should have no problem with 8 ohm speaker with this unit as you would with the 6 ohm speakers. The 6 ohm requirement is only not to go under that value. The only consequence of hooking up higher impedance speakers(8 ohm) to this system is that you will have slightly lower volume than with lower impedance speakers(6 ohm).

Apr 05, 2008 | RCA RT2250 System

2 Answers

Power but no sound

hook up the antenna at the back and try to tune-in to your favorite radio station.
read the description at the back of your rca rt2250, how to connect your antenna.
connect it properly and raise up the antenna, put it where the signal is good.

Feb 17, 2008 | RCA RT2250 System

1 Answer

Rca 2250

Sounds like your right side output is shot. And yes it can be fixed, but the cost factor would be higher than what you paid for the set itself. First see if your inputs are working correctly, this also could be your problem. Check all your connections.

Dec 29, 2007 | RCA RT2250 System

3 Answers

Rca Rt2250

just want to know how I can hook up my 8 ohm speakers to this receiver

Nov 13, 2007 | RCA RT2250 System

2 Answers

No sound for rt2250

Your problem is A blown output IC.. This should be taken to an authorized repair center. If you know how to service solid state electronics. Go to amd find an authorized parts house and order your manual from there. Or try If you dont find it online there get the number and call them. Good Luck

Aug 12, 2006 | RCA RT2250 System

1 Answer

RCA RT2250

Make that 3. There must be some kind of date chip in the thing

Dec 22, 2005 | RCA RT2250 System

Not finding what you are looking for?
RCA RT2250 System Logo

Related Topics:

314 people viewed this question

Ask a Question

Usually answered in minutes!

Top RCA Audio Players & Recorders Experts

The Knight
The Knight

Level 3 Expert

75767 Answers

Gyula Lacz

Level 3 Expert

486 Answers

Cindy Wells

Level 3 Expert

5521 Answers

Are you a RCA Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides