Question about Audio Players & Recorders

2 Answers

Security code for a kenwood kdc-319

I bought this kenwood kdc-319 receiver deck off of ebay and it says i need a four digit code in order to work it. and the guy that i bought it off of does not have one. so is there any way to solve this problem and get the code or reset it?

Posted by on

  • nandogriffin Feb 17, 2008

    yes

  • Graeme Ross
    Graeme Ross May 11, 2010

    do you have the remote for it also?

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Did this work for anyone?  It didn't for me.  I tried all three ways & two different remotes with no success.  It doesn't even look like there's a remote sensor that I can tell.

Posted on Feb 28, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,512 Answers

This is the workshop procedure for resetting the code.

KENWOOD SECURITY CODE CLEAR procedure


Your radio will require one of the following procedures.

Type 1
During the code request mode, while holding the DISP key depressed, press and hold the Volume UP or DOWN key for 3 seconds (so that “…” disappears).
Then using your remote enter your code.

Type 2
Press the "Auto" button and "Track up" on face of radio at the same time. The four dash lines ( . . . . ) should "disappear".

Then using your remote enter your code.

Type 3
Model# DPX-4020 and DPX-4030
Press and hold the 1 then the 6 preset key (preset keys are the buttons on face of radio for storing you "favorite" radio stations). "C" should display.
Then using your remote, enter your code.


Enter your number from the remote control unit. Your code number is 5227 (KCAR)

* Press numeric key “5” ( 2 times ) and press the Track UP/Next Track key
* Press numeric key “2” ( 3 times ) and press the Track UP/Next Track key
* Press numeric key “2” ( 1 time ) and press the Track UP/Next Track key
* Press numeric key “7” ( 2 times ) and press the Track UP/Next Track key

The security is canceled and the set enters the TUNER mode!
Please rate me FixYa for this solution. Good Luck :)

Posted on Feb 17, 2008

  • Graeme Ross
    Graeme Ross Jun 20, 2008

    ok, there is another trick to do at the end. Once you have entered the code procedure, press the "track up" button down for 3 secs.

  • bookham4
    bookham4 Jul 30, 2012

    will this work for meas i have no remote?

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a kenwood kdc-mp228, if I reset it will I need a security code


I had a problem as well with my KDC-MP6025 after I changed my car's battery. I called Kenwood four times asking about why my security code wouldn't take, and on the fourth call the tech said some random 2004 models (definately the MP6025, and probably it's sister receivers the KDC-X678 and the MP625) the decks firmware subtracts one from the 3rd digit if the sequence, i.e., if you set it for code 1234, you'd have to enter 1224. Since I sent Kenwood my product registration, it would have been nice for them to tell me this. I would have been BS if I had found out after if I had kept my $60 appointment to get the code cracked at the authorized repair place Kenwood recommended. Try that an see if it works. Cheers Greg.

Mar 16, 2015 | Kenwood Car Audio & Video

1 Answer

Kenwood KDC-319 CD Player Logo Problem with KDC-319 CD Player installed a kenwood kdc 319 in a 04 chevy malibu when i have car off i turn deck on an my cars dash board lights turn on Posted by A


I would start by disconnecting the radio and hooking it up right,the power should go through the ignition switch.So that when you turn the car off the radio will go off and to hear it on again you have to turn the key to accessory or start it.That might take care of a few of your problems.

Jun 25, 2012 | Kenwood KDC-319 CD Player

1 Answer

I need code to reset my kenwood kdc 319 car radio


Auth Kenwood servicer can remove the security code if can prove it's not hot. He will check the serial number with data base to see if it's been reported stolen, If you have purchase reciept that will work.

Nov 22, 2009 | Kenwood KDC-319 CD Player

1 Answer

Code for a kenwood kdc 319 cd player


i think the security code on most kenwoods is KCAR. you have to enter the code from the remote control though.

Oct 22, 2009 | Kenwood KDC-319 CD Player

1 Answer

Security code lost


if you did not add a code to unit just ignore that code say and push source and unit should come on all kenwood deck say that'

Oct 09, 2009 | Kenwood KDC-422 CD Player

1 Answer

Hi i have a problem with my customer i already selled him a kenwood car stereo the model num : KDC-W5031 and it appears waiting on the screen and also i dont have the security code


I had a problem as well with my KDC-MP6025 after I changed my car's battery. I called Kenwood four times asking about why my security code wouldn't take, and on the fourth call the tech said some random 2004 models (definately the MP6025, and probably it's sister receivers the KDC-X678 and the MP625) the decks firmware subtracts one from the 3rd digit if the sequence, i.e., if you set it for code 1234, you'd have to enter 1224. Since I sent Kenwood my product registration, it would have been nice for them to tell me this. I would have been BS if I had found out after if I had kept my $60 appointment to get the code cracked at the authorized repair place Kenwood recommended.

Sep 27, 2009 | Kenwood KDC-5021 CD Player

2 Answers

Kenwood KDC-319 CD Player Code dont have a


dont put a code all those radio say that when first power up just push the source button to do what you want

Sep 11, 2009 | Kenwood KDC-319 CD Player

1 Answer

Need to reset the code on my Kenwood deck.


you should try the defaults 0000,0123,1234. in most cases unless you or the original owner put in the security code. Worse case it will just keep turning off till you get it right.

Apr 13, 2009 | Kenwood KDC-MP4032 CD Player

1 Answer

My kenwood kdc-319


KENWOOD SECURITY CODE CLEAR procedure


Your radio will require one of the following procedures.

Type 1
During the code request mode, while holding the DISP key depressed, press and hold the Volume UP or DOWN key for 3 seconds (so that “…” disappears).
Then using your remote enter your code.

Type 2
Press the "Auto" button and "Track up" on face of radio at the same time. The four dash lines ( . . . . ) should "disappear".

Then using your remote enter your code.

Type 3
Model# DPX-4020 and DPX-4030
Press and hold the 1 then the 6 preset key (preset keys are the buttons on face of radio for storing you "favorite" radio stations). "C" should display.
Then using your remote, enter your code.


Enter your number from the remote control unit. Your code number is 5227 (KCAR)

* Press numeric key “5” ( 2 times ) and press the Track UP/Next Track key
* Press numeric key “2” ( 3 times ) and press the Track UP/Next Track key
* Press numeric key “2” ( 1 time ) and press the Track UP/Next Track key
* Press numeric key “7” ( 2 times ) and press the Track UP/Next Track key

The security is canceled and the set enters the TUNER mode!

Sep 25, 2007 | Kenwood KDC-319 CD Player

Not finding what you are looking for?
Audio Players & Recorders Logo

Related Topics:

462 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audio Players & Recorders Experts

kakima

Level 3 Expert

102366 Answers

 Grubhead
Grubhead

Level 3 Expert

4990 Answers

The Knight
The Knight

Level 3 Expert

73460 Answers

Are you an Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...