Question about GE (PSS26MSRSS) Side by Side Refrigerator

1 Answer

Ice Maker If the refrigerator motor is not running you have to hold the ice maker switch on for 1-2 minutes to get ice to come out. If motor is running it works fine.

Posted by on

  • Raebapap Mar 22, 2008

    Every thing is working but my ice maker appears not to have worker and isn't making Ice

  • Gary Davd
    Gary Davd May 11, 2010

    your question does not make any sense where you replying to a post and made a new one?? please state the problem again

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 184 Answers

PLEASE CLARIFY THE TERMS "MOTOR", "ICE MAKER SWITCH" AND "ICE TO COME OUT"

FAN MOTOR? COMPRESSOR? AUGER MOTOR?
ICE MAKER ON/OFF SWITCH? DISPENSE SWITCH? DOOR LIGHT SWITCH?
ICE TO COME OUT OF THE ICE MAKER? ICE TO COME OUT OF THE DISPENSER? ICE TO COME OUT OF BIN?

Posted on Apr 10, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ice maker water will not shout off Model WRS965CIAE it just runs till the tray overfills


Hello Andy;

My name is Peter. I am a retired field service appliance technician.

You have one of two problems.

1.) Ice maker module - Part Number 821515
http://www.ebay.com/bhp/ice-maker-module.

Fortunately, your ice maker is repairable. The module is like a little computer. It has a circuitry, a motor and a rotating gear set. The module tells the water solenoid valve when to turn on and how much water to fill the cube tray. Then it reads a sensor telling the module that the cubes are frozen. Then it turns on a heater under the cube mold. After a period the module tells the motor to turn on and harvest the ice cubes. It also has a lever arm on/off switch.

Watch the video. Remove the module from the ice maker. You may need a small flat head ***** driver to pop off the cover to get to it. Inspect the circuitry for any burn marks.

You will need to jump start the ice maker after reassembly and if you decide to just buy a new one.
1.) Insert a piece of 12 or 14 gauge jumper wire into the two holes on the face of the module marked: "T' and "H".
2.) Hold in the door light switch.
3.) After the module starts wait 5 seconds and remove the jumper, while still holding in the door light switch, until the ice maker has completer it's cycle and fills with water.
This will not solve your problem. This is how to start the icemaker - not shown in the video

Module Cost: Sears $98.56 + Tax
Ebay $25.00

2.) Ice Maker Water Solenoid Valve: Part Number W10341320.
If your ice maker is filling with water, then the solenoid is working, but the spool valve may be sticking and not closing quickly.

See general replacement video.

Solenoid Valve Cost: Sears $80.00
Search the internet for best price including used.


Go into the Sears website and put in your refrigerator model number. You will get diagrams and component part numbers.

Water Filters Lawn Garden Appliance Parts

Mar 16, 2016 | Whirlpool Refrigerators

1 Answer

I have a GE Profile pfss6pkx. The ice maker has stopped making ice and makes a clicking sound. Do I need a new ice maker or is there something I should try first?


Hello Dave;

My name is Peter. I am a retired field service refrigeration technician.

1.) Press the test button while hold the bottom freeze light switch in. The light switch is in the front top part of the freezer. Observe what happens.

2.) Your ice maker will not work if unless you reach temperature. look in the back of your freezer wall. Is there frost or ice build up?

3.) Do you have ice on the bottom of your freezer section? Then you have a frozen drain, ice built up and can not reach desired temperature.

4.0 You have a non repairable ice maker. Sometime these flex types become jammed with a ice cube in the mold. Check this out.

5.) Your ice maker has a sensor. This may be bad, but I do not think this is the problem.

Get back to me on what you find from the above.

Jan 16, 2015 | GE Profile PFSS6PKX Bottom Freezer French...

1 Answer

Dear Help 'Desk, I have a Samsung silver nano fridge/freezer. I've broken one of the removable door shelves in the freezer. Can you suggest a suitable (preferably clear) glue to repair the


Fevi-quick stick fast glue will be useful.It will take few minutes to hold the broken parts.Dont put overload of food stuff on the rejoined tray.But it will hold the basic load.

Before going to buy any parts directly.
Go through this troubleshooting help links.

-------------------------

This is list of refrigerator problems, which is normally faced in refrigerator.
You can go through the details, by clicking the link below:---

--------------
Refrigerator is not cooling properly?
http://technoanswers.blogspot.com/2011/06/refrigerator-is-not-cooling-properly.html
-----------
Both refrigerator and freezer not cooling properly in refrigerator?
http://technoanswers.blogspot.com/2011/06/both-refrigerator-and-freezer-not.html
----------
The ice maker not working: ---
http://technoanswers.blogspot.com/2011/06/ice-maker-stopped-working.html

------------
Compressor not running on refrigerator?
http://technoanswers.blogspot.com/2011/10/compressor-not-running-on-refrigerator.html
--------
Water dispenser not working on refrigerator?
http://technoanswers.blogspot.com/2011/10/water-dispenser-not-working-on_19.html

-------------

Ice maker stopped making ice?

http://alltypesofpartsreplacing.blogspot.com/2011/10/ice-maker-stopped-making-ice.html

-------------

Water Overflows in Ice maker and freezes inside?

http://alltypesofpartsreplacing.blogspot.com/2011/10/water-overflows-in-ice-maker-and.html

-------------

How to replace Ice maker assembly?

http://alltypesofpartsreplacing.blogspot.com/2011/10/how-to-replace-ice-maker-assembly.html

These will help.

Thanks,.

Dec 21, 2012 | Refrigerators

1 Answer

My Hoover Frost Free A class HTK 95AA has a trickling water noise coming from the back around the cooling pipes when switched on. The compressor gets very hot although the cooling pipes do not, is it


This is list of refrigerator problems, which is normally faced in refrigerator.
You can go through the details, by clicking the link below:---

--------------
Refrigerator is not cooling properly?
http://technoanswers.blogspot.com/2011/06/refrigerator-is-not-cooling-properly.html
-----------
Both refrigerator and freezer not cooling properly in refrigerator?
http://technoanswers.blogspot.com/2011/06/both-refrigerator-and-freezer-not.html
----------
The ice maker not working: ---
http://technoanswers.blogspot.com/2011/06/ice-maker-stopped-working.html

------------
Compressor not running on refrigerator?
http://technoanswers.blogspot.com/2011/10/compressor-not-running-on-refrigerator.html
--------
Water dispenser not working on refrigerator?
http://technoanswers.blogspot.com/2011/10/water-dispenser-not-working-on_19.html

-------------

Ice maker stopped making ice?

http://alltypesofpartsreplacing.blogspot.com/2011/10/ice-maker-stopped-making-ice.html

-------------

Water Overflows in Ice maker and freezes inside?

http://alltypesofpartsreplacing.blogspot.com/2011/10/water-overflows-in-ice-maker-and.html

-------------

How to replace Ice maker assembly?

http://alltypesofpartsreplacing.blogspot.com/2011/10/how-to-replace-ice-maker-assembly.html

These will help.
Thanks,.

Dec 21, 2012 | Refrigerators

1 Answer

Ice maker not working


Remove the front white plastic cover from the front of the ice maker, tape the freezer door switch down,Short T&H openings with an insulated piece of wire (14 gauge) to run the motor (hold the wire ends in the openings until the main gear start to rotate. If it doesn't start to rotate in a few seconds, try it again, before you replace the ice maker. If it starts to rotate, remove the wire and allow the ice maker toy advance, it should perform a complete cycle, including the fill.


Post back the results.

Nov 25, 2012 | Frigidaire FGHB2844L (27.8 cu. ft.) French...

1 Answer

Icemaker not working


In order to keep your refrigerator's ice maker working properly, there are some components that will require routine maintenance and inspection. Some of the most common problems that can occur with your ice maker are the ice maker not making any ice, making too much ice and not shutting off, the ice tasting bad, ice cubes too small or discolored and ice cubes not ejecting from the ice maker. Checking your ice maker for potential problems on a regular basis will keep it operating efficiently.

1.Inspect the water supply line for any signs of cracking or crimps in the line. A pinched water supply line can keep the water from getting to the ice maker, resulting in no ice or smaller than desired ice cubes. Check to verify that the water supply valve is open enough to provide an adequate supply of water to the ice maker.

2. Flush out the water supply lines if you are noticing a bad taste in the ice cubes. This can be done by disconnecting the lines and running hot water through them. Turn on the hot water at the kitchen sink and place one end of the water supply line near the tap, holding it in place to allow hot water to run through it. Place the other end of the supply line in the sink to allow the water to drain through.

3 Reattach the water supply lines to the water supply and refrigerator. Repeat step 2 for the water inlet hose which runs from the inlet valve to the ice maker. If the water supply lines are old or discolored, consider replacing them with new water supply lines.

4 Check the temperature in your freezer to verify that it is getting cold enough. The freezer's temperature should be at 5 degrees and can be set with a control dial, normally located in the refrigerator compartment of your appliance. To test the freezer's temperature, place a cup of cooking oil in the freezer with a cooking thermometer sitting in the cooking oil. Allow the oil to sit in the freezer for 2 hours and then check the temperature.

5 Check the ice maker's shutoff arm to verify that it is operating properly. To work normally, the shutoff arm should be in the lowered position. Inspect the arm for anything blocking it or preventing the arm from moving freely. Lift the arm up to see if the unit shuts off in the up position.

6 Unplug the refrigerator from the electrical outlet and remove the faceplate of the ice maker's shutoff switch with a screwdriver, located on the ice maker. Remove the entire ice maker unit from the freezer by undoing the screws that are holding it in place. Unplug the ice maker from the freezer and take it out of the freezer to work on.

7 Remove the mounting plate on the top of the ice maker by unscrewing the screws and lifting it off the unit. Locate the shutoff switch, which has three electrical wires attached to it. The shutoff switch is located directly under the shutoff arm of the ice maker. Pull the electrical wires off of the shutoff switch with needle-nose pliers and label them so you know how to put them back correctly.

8 Inspect the electrical terminals for any rust or corrosion. Use an electrical testing meter to verify that the shutoff switch is working properly. You should get a reading of 0 or infinity on the meter. If the shutoff switch is not giving a reading, replace it with a new switch and reattach the electrical wires to the switch.

9 Place the mounting plate back over the ice maker and attach it with screws, then reattach the entire ice maker unit to the freezer. Plug the ice maker wiring back into the freezer and put the face plate back over the front of the ice maker.

10 Plug the refrigerator back into the electrical outlet and allow the refrigerator to run for a couple hours. Inspect the ice maker to verify that it is working properly.

Hope this tips would help you.
Good day! : )

Sep 06, 2011 | Refrigerators

1 Answer

Not making ice cubes


Fill ice maker with tap water and let freeze. If ice dumps and water does not refill tray then the water control valve is defective. If ice remains in ice maker then ice maker is the problem.

I think Amana still uses the Whirlpool made ice maker. It consits of a mold, a paddel to remove the ice, a motor to drive the paddel and a cam. The electrical part consists of mold, thermostate or sensor ( use to be thermo-disc), micro switches, 1 to hold the unit running 2nd to alow water to flow at a certain time and a mold heater. Sequence of operation: Thermostate senses mold is cold, activates motor to turn paddels and cam. As cam turns it depresses a micro switch to hold motor running. Motor cam and paddel turn, mold heater is also turned on. As mold warms the paddels scoup out the ice. Contunes to turn until a spot on the cam activates another micro switch to allow water in. Motor continues, as cam reaches a spot it releases the micro switch for water andthen the switch holding the motor on and unit shuts off ready to do it again.

Sep 09, 2010 | Amana ARB2257C Bottom Freezer Refrigerator

2 Answers

Ice maker not dispensing ice


If the dispensor light switches to cubed or crushed , the panel is good . Remove the ice bin , and hold the light switch in . Press the arm for CRUSHED ice , and if you hear a buzzing or hum , then the auger motor is frozen . Use a hair dryer directly on the " forks " for a while , ocasionally holding switch and activating arm , until the forks move . Lower the freezer temp slightly and reinstall the ice bin .

Aug 11, 2009 | GE Profile Arctica 25.4 Cubic Feet...

1 Answer

Ice maker only dispenses crushed ice, won't dispense cubed ice anymore.


I have a GE TFX25ppbaaa refrigerator. The ice maker corkscrew motor would run and provide crushed ice only. The corkscrew motor would not run when the switch was moved to the cubed ice ( half moon) setting.

I replaced the large Light/ water/ crushed ice/cubed ice switch , ( product service number GEH WR55X129 ) ( part number GE 162D6372 PO17 )and it fixed the problem. Cost was about $43.00.

Apr 17, 2009 | Refrigerators

1 Answer

Ice maker stopped after electric shutoff


You may have a problem with the computer control board in the ice maker.  Try this.  Turn off the icemaker for about 2 minutes.  
Turn on the ice maker and press the clear button.  Press and hold this button for 12 seconds to get it to force extract.  This will confirm that the motors will work and push the ice cubes out.  Afterwards, let it run by itself.  If it still doesn't make ice, you will need to replace the icemaker.

Sep 19, 2008 | LG LSC26905TT Side by Side Refrigerator

Not finding what you are looking for?
GE (PSS26MSRSS) Side by Side Refrigerator Logo

Related Topics:

170 people viewed this question

Ask a Question

Usually answered in minutes!

Top Refrigerators Experts

Vish Iyer
Vish Iyer

Level 2 Expert

74 Answers

Todd Marr
Todd Marr

Level 2 Expert

77 Answers

John Tripp
John Tripp

Level 3 Expert

4636 Answers

Are you a Refrigerator Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...