Question about Audio Players & Recorders

1 Answer

Everytime i connect the usb it says that it is not recognizable. it also says that it has malfunctioned. what can i do? this thing is new out of the box.

Posted by on

  • blubba Feb 16, 2008

    my rca m202e mp3 player works perfectly except the diplay doesn't show up.it just happened one day.help me.

  • ifecoplc Dec 11, 2008

    my mp3 player model GK 915 when it is switched will not boot up and on the PC will not be recognized please some body should help men because I don't have the installation CD.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 73 Answers

Well, a generic USB error message doesnt telll you much.. Try it on a few different PC's.. If no luck, you probably have a brick..

You could start looking for mfg defects at the usb plug area, but from this point on it gets complicated..

Posted on Feb 17, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

THE SYSTEM IS CONNECTED DIRECTLY INTO THE RECEIVER THAN INTO THE MONITOR. AS FAR AS I KNOW IT IS NOT CONNECTED TO MY INTERNET.


one thing that you can do is turn on the auto login feature if the screen goes blank or the login session times out. I am not aware of any reason why the system would time out. The auto login setting will log you in in the event your screen goes blank.

Jan 08, 2017 | The Audio Players & Recorders

1 Answer

Want to use my current speakers with a new surround sound system. Current system is 5.1 channels, rated at 100w per channel @ 8. Ohms. New System is rated 145watts, 5.2 channels at 6 Ohms. Will b ok?


Hi Ronald.
8 Ohm speakers will work just fine as replacements for the
6 ohm speakers. When fitting speakers you need to consider
The power handling capability. The impedance and the frequencies
involved. Power handling is expressed in wattage ie 100W.
Unfortunately this can be expressed in rms, max or peak music. The rms value (root mean square) is the only really relevant figure as this is the continuose handling power at 1 KHz. The impedance
is the resistance that the amp sees but is not a dc resistance and
varies with frequency. The lower the impedance the more power
will be drawn from the amp. In the event of a short circuit across
the speaker the amp will try to deliver infinite power into an infinitly
small load in an infinitesimal amount of time and will self destruct.
Using an 8 Ohm speaker draws less power than a 6 Ohm speaker.
Connecting speakers in parallel; results in the impedance beingreduced. For example two 8 Ohm speakers in parallel will result
in a 4 Ohm impedance load but in series will be 16 Ohms.
Incidentally the the .1 (5.1) is the sub woofer which only has
to handle the bass frequencies, a small percentage of the
amplifiers overall frequency response..
Connect your speakers and then power up the amp last
after double checking there are no shorts on the speaker
cables.
All the very best from Vintie.





Jan 07, 2017 | Audio Players & Recorders

1 Answer

How do I connect my technical pro dual 10 band equalizer to my professional hybrid amplifier


Use the pre in out connections or any in/out connectors that you have. Can you send a picture?
ELECTREPAIRUSA@ELECTREPAIRUSA or you can contact us at that address as we repair/renovate all items electronic and electrical old and new.

Dec 09, 2016 | Dual Audio Players & Recorders

1 Answer

How do I test for a poor ground wire as opposed to a bad ground wire?


One tiny wire has very little resistance. Turn up your Ohm meter to it's highest setting. Be sure to have it calibrated exactly the same for each test (zeroed out). The very good connection should read infinite but the tiny connection should show a tiny bit of resistance. It's difficult but not impossible. Get a friend to help so the resistance in your body doesn't affect the data. Use one hand and new clips.

Jan 23, 2015 | Audio Players & Recorders

1 Answer

Switch on akai58022 tower speaker, it worked when I got it today and now it wont even switch on


what do you have it plugged-into for power ? it uses the 8-pin Apple Lightning dock connector. If you are using a USB adapter for that, then be aware that a USB-port will only let you draw 500mA or 1/2 an Amp of power....more than that will cause failures and damage to the USB port and the Hub even.

Nov 13, 2014 | Audio Players & Recorders

2 Answers

Marantz how to connect 6005 amplifier to ipod


There are many solutions, I show two. The tip photo, shows a more expansive one. the lower photo the cheaper one. But both have two tulip plugs on the side for the amplifier and one 3,5 mm stereo telephone plug to the other side.
I tried both on a good stereo set, and could not hear different quality in sound. My guess, the quality comping from my iPods, iPhone and iPad is not the same as from my CD player. On the CD player, a better cable proved to give a better sound.


c25e6b72-61d1-4158-8864-9fee0335d5fc.jpg 0c90f720-e235-4415-a30c-8a9f98411676.jpg

May 26, 2014 | Audio Players & Recorders

2 Answers

Hi,Just purchased 2 antec gain Bluetooth receivers type bxr 100. Operating instructions are not included. Maybe it's just me, but i'm not succeeding in getting them to work. No lights at all when they


Make sure that the unit is fully charged by a micro USB the light on it will be red until it's fully charged put phone in search mode and press the center button until the light flashes red and blue after the phone finds it you should have an option to auto pair when it's not in use it will turn off when paired and working pressing either track button will start the music player then just play with the buttons and see what it does you can stop anything from the phone controls

Mar 18, 2014 | Antec BXR-100 Gry Audio...

2 Answers

Iwave pod bluetooth speaker


Unless your PC is Bluetooth capable, you'll need to get a Bluetooth device to make it so. This is just one of many such devices to select from. Amazon com Roker Ultra Mini CSR Bluetooth 4 0 Usb Adator for PC and... They vary in size and price. Shop around to find one that best suits your budget. But you want an adaptor/receiver specifically for Bluetooth. (you will need an empty USB port for the adaptor)

Hope this information helps, best of luck!

Feb 06, 2014 | Audio Players & Recorders

1 Answer

HMDX Jam wireless speaker cannot be paired with my computer


Go to your Bluetooth settings, go to the "Audio/Video" tab, under the "Content Protection" section uncheck the "Connect to content protection enabled headset only" and your bluetooth speaker(s) should now work.

hmdx-jam-wireless-speaker-cannot-paired-545ferrkqkuowltb2dothasu-3-0.jpg

Feb 02, 2013 | Audio Players & Recorders

Not finding what you are looking for?
Audio Players & Recorders Logo

Related Topics:

165 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audio Players & Recorders Experts

kakima

Level 3 Expert

100387 Answers

 Grubhead
Grubhead

Level 3 Expert

4706 Answers

The Knight
The Knight

Level 3 Expert

71172 Answers

Are you an Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...