Question about Indesit 24 in. DI67 Free-standing Dishwasher

1 Answer

Dishwasher filling up then stopping

Please help . my dishwasher is filling up then stopping on every cycle . i have tried tilting it forward reseting it and starting again but it just keeps stopping when it gets so far

Posted by on

  • tav1066 Apr 24, 2008

    having same problem. what is solution to issues raised?

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 236 Answers

Is it going into the wash or just filling and thats it? if it fills and does nothing straight after it is probably the wash motor is jammed or seized. if the d/w starts to wash then stops it may be the heater is faulty.

Posted on Feb 16, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a ASKO D3111/8 dishwasher that will not stop pumping unless i turn it off at the power?


Hi alan gorman1,

I believe the Float Switch has been activated, do the following:

- Tilt the dishwasher back 35 Degrees.
- Keep it there until water stops running out the side (If any)
- Then tilt the dishwasher forward 35 Degrees
- Keep it there until water stops running out the side (If any)

This should empty water trapped in the lower part of the Dishwasher, and deactivate the float switch.

Kind Regards
Jedemeyer1

* Hope this solution helped you, if it did, please rate it.

Jun 10, 2011 | Dishwashers

1 Answer

In my dishwasher Whirpool ADP 8967 after the washing cycle start the drying cycle when start it I got the error F7 and the machine stop the cycle. Can some one help me?


Hi simone_b_630,

F7 is known as a fill fault.


1) Remove the filters and the mesh filter, clean out the black grid in the bowl carefully. Don't burst the membrane inside it.

2) Try the machine again after resetting it. (Reset it by holding the start button for 8 - 10 seconds)

3) If the fault persists, take off the left hand panel and unplug the flow-meter, located bottom front of the large plastic water matrix.

4) Plug it back on, reset the machine and try it again.

Also make sure the fill hose isn't kinked and that water is actually entering the machine.

* If you found this solution helpful, please rate 4 thumbs up and leave a small testimonial. :-)

Apr 19, 2011 | Dishwashers

2 Answers

I have a haier dishwasher but the water wont drain out of it. the power light remains on but turning the settings dial has no effect - looks like the pump may be blocked. how can i carry out a factory...


you maybe right but before doing machine reset button, you need to clean the machine be sure there's no jam in mechanical parts. also not all machine have reset button outside, some are hide and inside the power supply module so look for it and be careful.

Feb 04, 2011 | Haier HDP18PA Stainless Steel...

1 Answer

D 3100 continues to pump out. Program stops and program button flashes


We have just fixed our Asko 3100 dishwasher. You need to undo the screws attaching the unit to the side cabinets. Pull dishwasher out and tilt forward to drain. Put towels down as lots of water. Machine seems ok now and running on a cycle.

Nov 06, 2010 | Asko Dishwashers

1 Answer

Roper Dishwasher leaks from float or float switch onto floor


you could be usiong way to mauch soap try filling only one of the soap trays or even try doing one wash without any soap at all
this unit tends to do this if you have to much soap in the unit left over from the last load...
beyond that your machine is proibaly tilted to far forward you can lift it, by lowering the front legs begind the toekick

Oct 25, 2009 | Roper 24 in. RUD4000M Built-in Dishwasher

1 Answer

Kenmore Dishwasher 5871525 stops running after a few minutes


sounds like a stuck key pad since you said the normal wash button flashed.. the other thing is try holding the door shut while you run it.. to see of it is maybe not latching properly..

Apr 10, 2009 | Kenmore 15762 Dishwasher

5 Answers

The washer keeps beeping and trying to drain as soon as it is turned on


I have a Haier HDP18PA with the same problem... I tried tilting mine backwards while running...this made a mess BUT the beeping stopped BUT the lights were still flashing. Turned it off and started it again and the lights still were flashing BUT no beeping. Decided to try tilting it forward while running ... made another mess BUT the lights stopped flashing. Turned it off again and restarted it and it is now running fine. Good luck!

May 05, 2008 | Haier HDP18PA Stainless Steel...

1 Answer

Hi. I have a Dishlex global 300 series and it starts going through the cycle ok but after about 5 minutes it starts to fill up again and the eco light starts to flash and it won't stop filling up and...


The operating manual says under problem solver thatin such a situation it has an incorrect fill level or fill time and recommends then the need for a service agent.

Try holding the start and programme buttons down at the same time until the machine beeps. This will reset it in case it is just a computer problem.

Apr 30, 2008 | Dishwashers

2 Answers

Kenmore Ultra Wash Dishwasher LIghts are blinking....


I just read this for the same problem: push sanitize, then heat and dry, sanitize, heat and dry, sanitize, heat and dry, cancel, then open and close the door. It worked. The dishwasher is running correctly even as I type this. 

Feb 11, 2008 | Kenmore 24 in. 17262 Built-in Dishwasher

1 Answer

Whirlpool Dishwasher Fills and then Stops


  Check your connection where you connected dishwasher to power cord.  

Oct 25, 2007 | Whirlpool 24 in. GU2500 XTP Built-in...

Not finding what you are looking for?
Indesit 24 in. DI67 Free-standing Dishwasher Logo

Related Topics:

765 people viewed this question

Ask a Question

Usually answered in minutes!

Top Indesit Dishwashers Experts

Ken Johnston
Ken Johnston

Level 1 Expert

56 Answers

Eric Taylor

Level 2 Expert

42 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

Are you an Indesit Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...